• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.1
• /
• pp.47-53
• /
• 2011

$SF_6$ (Sulfur hexafluoride) possesses high GWP (Global Warming Potential) as sepcified by the IPCC (Intergonvernmental Panel of Climate Change). Recently, the recovery-separtion of $SF_6$ research area, including permeation properties studies using various membrane's materials and the practical operation of recovery-separtion using membrane of waste $SF_6$ gas is in the initial state. The separation efficiency of a single $SF_6$ and waste $SF_6$ mixture was evaluated using a PSF (polysulfone), PC (tetra-bromo polycarbonate) and PI (polyimide) hollow fiber membranes. According to the results of single gases permeation properties, PI membrane has the highest permselectivity of $N_2$ gas in $N_2/SF_6$ gas. Under the condition of P=0.5 MPa, the highest concentration of recovered $SF_6$ is 95.6 vol % in the separation experiment of $SF_6/N_2$ mixture gas by PC membrane. Under the operation pressure of P=0.3 MPa at a fixed retentate flow rate fixed of 150 cc/min, the maximum recovery efficiency of $SF_6$ is up to 97.8% by PSF membrane. From the results above, it is thought that the separation and recovery technique of $SF_6$ gas using membrane will be used as the representative eco-technology in the $SF_6$ gas treatment in the future.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.263-271
• /
• 2010

Intermittent CSR testing was used to investigate the degradation of an FKM O-ring, also the prediction of its life-time. An intermittent CSR jig was designed taking into consideration the O-ring's environment under use. The testing allowed observation of the effects of friction, heat loss, and stress relaxation by the Mullins effect. Degradation of O-rings by thermal aging was observed between 60 and $160^{\circ}C$. In the high temperature of range ($100-160^{\circ}C$) O-rings showed linear degradation behavior and satisfied the Arrhenius relationship. The activation energy was about 60.2 kJ/mol. From Arrhenius plots, predicted life-times were 43.3 years and 69.9 years for 50% and 40% failure conditions, respectively. Based on TTS (time-temperature superposition) principle, degradation was observed at $60^{\circ}C$, and could save testing time. Between 60 and $100^{\circ}C$ the activation energy decreased to 48.3 kJ/mol. WLF(William-Landel-Ferry) plot confirmed that O-rings show non-linear degradation behavior under $80^{\circ}C$. The life-time of O-rings predicted by TTS principle was 19.1 years and 25.2 years for each failure condition. The life-time predicted by TTS principle is more conservative than that from the Arrhenius relationship.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.1
• /
• pp.1-10
• /
• 2023

The cathode, which is one of the four major components of a lithium secondary battery, is an important component responsible for the energy density of the battery. The mixing process of active material, conductive material, and polymer binder is very essential in the commonly used wet manufacturing process of the cathode. However, in the case of mixing conditions of the cathode, since there is no systematic method, in most cases, differences in performance occur depending on the manufacturer. Therefore, LiMn₂O₄ (LMO) cathodes were prepared using a commonly used THINKY mixer and homogenizer to optimize the mixing method in the cathode slurry preparation step, and their characteristics were compared. Each mixing condition was performed at 2000 RPM and 7 min, and to determine only the difference in the mixing method during the manufacture of the cathode other experiment conditions (mixing time, material input order, etc.) were kept constant. Among the manufactured THINKY mixer LMO (TLMO) and homogenizer LMO (HLMO), HLMO has more uniform particle dispersion than TLMO, and thus shows higher adhesive strength. Also, the result of the electrochemical evaluation reveals that HLMO cathode showed improved performance with a more stable life cycle compared to TLMO. The initial discharge capacity retention rate of HLMO at 69 cycles was 88%, which is about 4.4 times higher than that of TLMO, and in the case of rate capability, HLMO exhibited a better capacity retention even at high C-rates of 10, 15, and 20 C and the capacity recovery at 1 C was higher than that of TLMO. It's postulated that the use of a homogenizer improves the characteristics of the slurry containing the active material, the conductive material, and the polymer binder creating an electrically conductive network formed by uniformly dispersing the conductive material suppressing its strong electrostatic properties thus avoiding aggregation. As a result, surface contact between the active material and the conductive material increases, electrons move more smoothly, changes in lattice volume during charging and discharging are more reversible and contact resistance between the active material and the conductive material is suppressed.

• Economic and Environmental Geology
• /
• v.56 no.1
• /
• pp.23-53
• /
• 2023

In this review paper, previous studies on layered double hydroxides (LDHs) published in the Korean Citation Index (KCI) were examined to investigate a research trend for LDHs in Korea. Since the first publication in 2002, 160 papers on LDHs have been published until January 2023. Among the 31 academic fields, top 5 fields appeared in the order of chemical engineering, chemistry, materials engineering, environmental engineering, and physics. The chemical engineering shows the highest record of published paper (71 papers) while around 10 papers have been published in the other four fields. All papers were reclassified into 15 research fields based on the industrial and academic purposes of using LDHs. The top 5 in these fields are in order of environmental purification materials, polymer catalyst materials, battery materials, pharmaceutical/medicinal materials, and basic physicochemical properties. These findings suggest that researches on the applications of LDH materials in the academic fields of chemical engineering and chemistry for the improvement of their functions such as environmental purification materials, polymer catalysts, and batteries have been being most actively conducted. The application of LDHs for cosmetic and agricultural purposes and for developing environmental sensors is still at the beginning of research. Considering a market-potential and high-efficiency-eco-friendly trend, however, it will deserve our attention as emerging application fields in the future. All reclassified papers were summarized in our tables and a supplementary file, including information on applied materials, key results, characteristics and synthesis methods of LDHs used. We expect that our findings of overall trends in LDH research in Korea can help design future researches with LDHs and suggest policies for resources and energies as well as environments efficiently.

• Membrane Journal
• /
• v.27 no.4
• /
• pp.344-349
• /
• 2017

Alkaline fuel cells using polymer electrolyte membranes are expected to replace proton exchange membrane fuel cells, which have similar system configurations. In particular, in alkaline fuel cells, a low-cost non-platinium catalyst can be used. In this study, to fabricate high performance and high durability anion exchange membranes for alkaline fuel cell systems, two kinds of supports, polybenzoxazole and polyethylene supports, were impregnated with Fumion FAA ionomer, by which we tried to fabricate the support-impregnated membrane which has higher mechanical strength and higher ion conductivity than the Fumion series. Finally, the Pore-filling membranes were successfully fabricated and ionic conductivity and mechanical properties were different depending on the properties of the supports. In the pore-filling membranes with Fumion ionomer on the PE support, excellent mechanical properties were obtained, but ionic conductivity decreased. On the other hand, when the PBO support was impregnated with Fumion ionomer, high ionic conductivity was shown after impregnation due to high basicity of PBO, but the mechanical strength was relatively low as compared with Fumion-PE membrane. As a result, it was concluded that it is necessary to consider the characteristics of the support according to the operating conditions of the alkaline fuel cell during the preparation of the pore-filling membranes.

• Investigative Magnetic Resonance Imaging
• /
• v.7 no.1
• /
• pp.39-46
• /
• 2003

Purpose : To develop a theoretical model for magnetic relaxation behavior of the superparamagnetic nano-particle agent, which demonstrates multi-functionality such as liver- and lymp node-specificity. Based on the developed model, the computer simulation was performed to clarify the relationship between relaxation time and the applied magnetic field strength. Materials and Methods : The ultrasmall superparamagnetic iron oxide (USPIO) was encapsulated with biocompatiable polymer, to develop a relaxation model based on outsphere mechanism, which was resulting from diffusion and/or electron spin fluctuation. In addition, Brillouin function was introduced to describe the full magnetization by considering the fact that the low-field approximation, which was adapted in paramagnetic case, is no longer valid. The developed model describes therefore the T1 and T2 relaxation behavior of superparamagnetic iron oxide both in low-field and in high-field. Based on our model, the computer simulation was performed to test the relaxation behavior of superparamagnetic contrast agent over various magnetic fields using MathCad (MathCad, U.S.A.), a symbolic computation software. Results : For T1 and T2 magnetic relaxation characteristics of ultrasmall superparamagnetic iron oxide, the theoretical model showed that at low field (<1.0 Mhz), $\tau_{S1}(\tau_{S2}$, in case of T2), which is a correlation time in spectral density function, plays a major role. This suggests that realignment of nano-magnetic particles is most important at low magnetic field. On the other hand, at high field, $\tau$, which is another correlation time in spectral density function, plays a major role. Since $\tau$ is closely related to particle size, this suggests that the difference in R1 and R2 over particle sizes, at high field, is resulting not from the realignment of particles but from the particle size itself. Within normal body temperature region, the temperature dependence of T1 and T2 relaxation time showed that there is no change in T1 and T2 relaxation times at high field. Especially, T1 showed less temperature dependence compared to T2. Conclusion : We developed a theoretical model of r magnetic relaxation behavior of ultrasmall superparamagnetic iron oxide (USPIO), which was reported to show clinical multi-functionality by utilizing physical properties of nano-magnetic particle. In addition, based on the developed model, the computer simulation was performed to investigate the relationship between relaxation time of USPIO and the applied magnetic field strength.

• Journal of Korean Society of Forest Science
• /
• v.71 no.1
• /
• pp.14-21
• /
• 1985

This study was carried out in order to prevent the devaluation of wood itself and wood products causing by anisotropy, hygroscopicity, shrinkage and swelling - properties that wood itself only have, in order to improve utility of wood, by emphasizing the natural beautiful figures of wood, to develop the dimensional stabilization techniques of wood with PEG that it is a cheap, non-toxic and the impregnation treatment is not difficult, on the effects of PEG molecular weights (200, 400, 600, 1000, 1500, 2000, 4000, 6000) and species (Pinus densiflora S. et Z., Larix leptolepis Gordon., Cryptomeria japonica D. Don., Cornus controversa Hemsl., Quercus variabilis Blume., Prunus sargentii Rehder.). The results were as follows; 1) PEG loading showed the maximum value (137.22%, Pinus densiflora, in PEG 400), the others showed that relatively slow decrease. The lower specific gravity, the more polymer loading. 2) Bulking coefficient didn't particularly show the correlation with specific gravity, for the most part, indicated the maximum values in PEG 600, except that the bulking coefficient of Quercus variabilis distributed between the range of 12-18% in PEG 400-2000. In general, the bulking coefficient of hardwood was higher than that of softwood. 3) Although there was more or less an exception according to species, volumetric swelling reduction was the greatest in PEG 400. That is, its value of Cryptomeria japonica was the greatest value with 95.0%, the others indicated more than 80% except for Prunus sargentii, while volumetric swelling reduction was decreased less than 70% as the molecular weight increase more than 1000. 4) The relative effectiveness of hardwood with high specific gravity was outstandingly higher than softwood. In general, the relative effectiveness of low molecular weight PEG was superior to those of high molecular weight PEG except that Quercus variabilis showed more than 1.6 to the total molecular weight range, while it was no significant difference as the molecular weight increase more than 4000. 5) According to the analysis of the results mentioned above, the dimensional stabilization of hardwood was more effective than softwood. Although volumetric swelling reduction was the greatest at a molecular weight of 400. In the view of polymer loading, bulking coefficiency reduction of swelling and relative effectiveness, it is desirable to use the mixture of PEG of molecular weight in the range of 200-1500. To practical use, it is recommended to study about the effects on the mixed ratio on the bulking coefficient, reduction of swelling and relative effectiveness.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.3 s.151
• /
• pp.386-395
• /
• 2006

Chitosan, a natural polymer has been used to nonwoven fabrics based polypropylene for sanitary top sheets. The changes in mechanical properties relating to the surface structure of functionally improved nonwoven fabrics were investigated with respect to the molecular weight and concentration of chitosan that was used. Low molecular weight(LMW) chitosan treated fabric was found to be evenly coated on the fabrics. It was shown that the bending and shearing characteristics of chitosan treated fabrics increased, which helped to make it stronger and harder, while shape stability improved following treatment using high molecular weight(HMW) chitosan. And the surface structure of treated fabrics was smooth and the sensitivity of its bulk improved somewhat. The treated fabrics were not overly stiff because the increase in Koshi value was not considerable compared to that of the bending characteristics. In the change of hand value relating to chitosan treated fabrics, THV generally improved. In the case of a 0.5$\%$ chitosan, HMW chitosan treated fabrics produced better THV than LMW chitosan treated fabrics. However, in the case of a 1.0$\%$ chitosan, THV of LMW chitosan treated fabrics produced outstanding results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.135.1-135.1
• /
• 2010

최근 고온에서 사용 가능한 PEMFC용 고분자전해질 막 개발에 대한 연구가 활발히 진행되고 있다. PEMFC가 고온에서 작동하게 되면 높은 성능과 많은 장점을 갖게 된다. PEMFC를 $100^{\circ}C$ 이상에서 운전하게 될 경우 백금 전극 반응을 향상시켜 고가의 백금 촉매 양을 줄일 수 있게 되고, 수소연료 속에 미량 포함된 CO에 의한 촉매표면 피독현상에 대한 내구성을 높일 수 있어 저 순도 수소연료 사용이 가능해 진다. 또한 가습장치와 수소 연료 개질장치의 부피를 줄일 수 있게 되어 전체적인 PEMFC 시스템이 단순화 된다. 현재 연료전지용 고분자 전해질막으로 DuPont사의 과-불소계 고분자 전해질막인 Nafion$^{(R)}$이 가장 널리 사용되고 있다. Nafion$^{(R)}$은 유연한 분자구조 안에 소수성이 강한 주사슬과 친수성을 나타내는 술폰산이 결합된 곁사슬이 존재하여 술폰화 곁사슬의 클러스터 둘레에는 친수성 영역이 형성이 되기때문에 소수/친수 상 분리가 잘되어 이온 클러스터 형성이 용이하지만 제조비용이 높은 단점을 갖고 있다. 특히, 전해질 막내에서 Bronsted base 역할을 하는 물에 의해 이온전도가 이루어지기 때문에 고온에서는 수분증발로 인해 성능이 급격히 감소된다. 따라서, 본 연구에서는 고온 저가습 조건에서 운전이 가능하고 Nafion이 갖는 문제점을 해결하고자, 내열특성이 뛰어나며 높은 수소이온 전도도 학보가 용이한 Sulfonated Poly(aryl ether)sulfone(SPAES) 고분자 전해질에, 고온에서도 수화성이 유지될 수 있도록 지르코니아를 황산화한 sulfated zirconia(s-$ZrO_2$)를 함침하여 복합 고분자전해질막을 제조하여 고온 저가습 조건에서의 수소이온 전도 특성에 관한 연구를 수행하였다. 개발된 막의 물리/화학적 특성은 water content(Wup%), 이온교환 용량(IEC, meq $g^{-1}$), 수소이온전도도(s $cm^{-1}$) 열 중량 분석(TGA), X선 회절분석(XRD) 등을 통하여 분석 및 관찰하였다. 내화학 및 열적 특성분석 결과, 황산화 반응공정으로 $ZrO_2$에 술폰산기가 안정적으로 결합하고 있음이 관찰되었으며, 본 연구에서 개발된 유 무기 복합막이 $250^{\circ}C$이상 열적안정성을 확보하고 있는 것으로 판단되었다. $100^{\circ}C$ 이하의 저온 영역에서, 일정 비율의 s-$ZrO_2$/SPAES막에서 이온교환용량(IEC)이 순수 SPAES 막보다 낮음에도 불구하고, water uptake가 증가함과 동시에 수소이온 전도도가 향상된 것을 관찰하였다. 또한, 고온에서는 수소이온이 자유롭게 이동할 수 있는 water channel을 형성하는 free water는 증발 하지만 s-$ZrO_2$와 SPAES의 술폰산기 사이에 강력하게 결합하고 있는 bound Water는 $100^{\circ}C$ 이상의 고온 영역에서도 존재하여, 비록 무가습 조건에서도 일정 비율의 s-$ZrO_2$/SPAES50 전해질 막의 경우, 높은 전도도를 나타냄을 관찰할 수 있었다. 따라서 본 연구를 통해 저가습 고온 적용을 목적으로 개발된 s-$ZrO_2$/SPAES50막은 우수한 내열 특성을 나타냄과 동시에 저가습 고온 영역($120^{\circ}C$, $50RH{\downarrow}$)에서 높은 수소이온 전도도를 유지하여, 고온 저가습 연료전지 운전에 적합할 것으로 사료된다.

• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.250-256
• /
• 2013

Gasoline generates organic acid and polymer (gum) by hydrocarbon oxidation depending on the storage environment such as temperature and exposure to sunlight, which can cause metal corrosion, rubber and resin degradation and vehicle malfunction caused by accumulation in fuel supply system. The gasoline which has not been used for a long time in bi-fuel (LPG-Gasoline) vehicle causes problems, and low octane number gasoline have evaporated into the field, but the exact cause has not been studied yet. In this study, we suggest a plan of quality management by investigating the gasoline oxidation behavior. In order to investigate the oxidation behavior of gasoline, changes of gasoline properties were analyzed at various storage conditions such as storage time, storage vessel type (vehicle fuel tank, PE vessel and Fe vessel) and storage circumstances (sunlight exposure and open system, etc.). Currently distributing gasoline and bioethanol blended fuel (blended 10%) were stored for 18 weeks in summer season. The sample stored in PE vessel was out of quality standard (octane number, vapor pressure, etc.) due to the evaporation of the high octane number and low boiling point components through the vessel cap and surface. Especially, the sunlight exposure sample stored in PE vessel showed rapid decrease of vapor pressure and increase of gum. Bioethanol blended fuel showed similar results as gasoline.