• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1227-1240
• /
• 2014

Abandoned mines often cause environmental problems, such as alteration of landscape, metal contamination, and landslides due to a heavy rainfall. Geotechnical and rheological tests were performed on waste materials corrected from Imgi waste rock dump, located in Busan Metropolitan City. Debris flow mobility was examined with the help of 1-D BING model which was often simulated in both subaerial and subaqueous environments. To determine flow curve, we used a vane-penetrated rheometer. The shear stress (${\tau}$)-shear rate (${\dot{\gamma}}$) and viscosity(${\eta}$)-shear rate (${\dot{\gamma}}$) relationships were plotted using a shear stress control mode. Well-known rheological models, such as Bingham, bilinear, Herschel-Bulkley, Power-law, and Papanastasiou concepts, were compared to the rheological data. From the test results, we found that the tested waste materials exhibited a typical shear shinning behavior in ${\tau}$-${\dot{\gamma}}$ and and ${\eta}$-${\dot{\gamma}}$ plots, but the Bingham behavior is often observed when the water contents increased. The test results show that experimental data are in good agreement with rheological models in the post-failure stage during shearing. Based on the rheological properties (i.e., Bingham yield stress and viscosity as a function of the volumetric concentration of sediment) of waste materials, initial flowing shape (5 m, 10 m, and 15 m) and yield stress (100 Pa, 200 Pa, 300 Pa, and 500 Pa) were input to simulate the debris flow motion. As a result, the runout distance and front velocity of debris flow are in inverse propositional to yield stress. In particular, when the yield stress is less than 500 Pa, most of failed masses can flow into the stream, resulting in a water contamination.

• Korean Journal of Food Science and Technology
• /
• v.29 no.5
• /
• pp.932-938
• /
• 1997

Changes in viscosity and dynamic theological properties of Job's-tears were measured by Bohlin dynamic tester as a function of moisture, and measurement was performed within a linear viscoelastic range. The result of the shear stress vs shear rate of Job's-tears at different moisture contents $(50{\sim}75%)$ was applied to mathematical models and Herschel-Bulkley model showed the highest correlation coefficient. Lower moisture content (55%) produced higher yield stress and consistency index, but lower flow behavior index, whereas higher moisture content showed reverse effects. Job's-tears with $50{\sim}70%$ moisture contents showed a higher storage modulus (G') than loss modulus (G') at all frequencies, showing a higher concentrated polymer characteristics. However, higher moisture content (>75%) showed crossover point between G' and G', and frequency dependency. As the moisture content was increased, the amount of viscoelastic properties such as G', G', complex viscosity decreased during heating, and initial temperature and miximum value of viscoelastic properties shifted to higher temperatures, representing the moisture-dependence of Job's-tears upon theological properties.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.6
• /
• pp.726-731
• /
• 1999

It was discovered that ammonium phosphate in the medium played an important role in both growing mycelium and producing exopolysaccharides (EPS) from G. lucidum. In lower concentration levels of ammonium phosphate (0-3 g/l), an improved mycelial growth was observed by maintaining more filamentous morphology than in high concentrations (5-11 g/l). In addition, it was confirmed by comparing the factual dimension and frequency of the area regarding the mycelial pellets. This must be attributed to limitations of nutrient transfer by maintaining filamentous mycelium during the cultivation in a low ammonium phosphate containing medium. On the other hand, the best EPS production was observed in medium with the absence or low concentration of ammonium phosphate. The shear stress of the culture broth was greatly affected by the shear rate, as compared with that of the culture broth with high ammonium phosphate concentration. The rheological characteristics of the fermentation broth and filtrate worked well according to the Herschel-Bulkley model. It was also found that the morphological changes of the mycelium resulting from the ammonium phosphate concentration directly affected the rheological characteristics of the system and resulted in reversely affecting the EPS production levels. Based on these results, it can be concluded that delicate regulation of the ammonium phosphate concentration in the culture media should be provided in order to obtain optimal mycelial growth and/or EPS production.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.29 no.2
• /
• pp.198-203
• /
• 2000

A highly viscous biopolymer from Bacillus coagulans CE-74 was purified and its rheological properties were studied The rheological properties of biopolymers produced by Bacillus coagulans CE-74 were studied at the temperature ranges with 20~8$0^{\circ}C$, at the concentration of 0.5~4.0%, at the pH ranges from 3 to 1 and at the shear rate fo 7.34~73.38 sec-1. The apparent viscosity of biopolymer was decreased with increasing shear rate, and thereby biopolymer showed pseudoplastic characteristics. Biopolymer solution showed a characteristic of non-Newtonian fluid properties. At the concentration of 1%, the consistency index and the flow behavior index were shown at 2.64 poise. sec11 and 0.8571, respectively. All dispersions were pseudoplastic fluids described accurately by Herschel-Bulkley model. The change of the biopolymer viscosity on pH showed the highest value at the pH 7.0 and it showed lower at acidic conditon that at alkaline condition comparatively.

• Korean Journal of Food Science and Technology
• /
• v.22 no.6
• /
• pp.646-650
• /
• 1990

To develop a new form of spice material by concentration of garlic juice, its rheological properties were investigated. In the temperature range of $15\;to\;65^{\circ}C$, the garlic juice with the solid content of $32\;to\;60^{\circ}Brix$ was considered as a pseudoplastic fluid. Flow and consistency indices of the juice interpreted by power-law equation varied from $0.9937\;to\;0.6130\;and\;0.0041\;to\;3.1886Pa{\;s^n$, respectively. Apparent viscosity was lineally decreased as shear rate was increased. Activation energy for the flow of the garlic juice changed in the range of 11,216 to 23,195 kJ/kg mol.

• Food Science and Biotechnology
• /
• v.15 no.1
• /
• pp.33-38
• /
• 2006

This study was performed to provide basic rheological data of dandelion root concentrates in order to predict their processing aptitude and usefulness as functional foods material. The hot water and 70% ethanol extracts of dandelion root were concentrated at 5, 20, and 50 Brix, and their static viscosity, dynamic viscosity, and Arrhenius plots were investigated. Almost all hot water concentrates showed the typical flow properties of a pseudoplastic fluid, but evaluation using the power law model indicated that the 70% ethanol concentrates showed a flow behavior close to a Newtonian fluid. The apparent viscosity of hot water and 70% ethanol concentrates decreased with increasing temperature. Yield stresses of hot water and 70% ethanol concentrates by Herschel-Bulkley model application were in the range of 0.026 - 1.368 Pa and 0.022 - 0.238 Pa, respectively. The effect of temperature and concentration on the apparent viscosity was examined by Arrhenius equation. The activation energies of hot water and 70% ethanol concentrates were in the range of $8.762-23.778{\times}10^3\;J/mol{\cdot}kg$ and $3.217-20.384{\times}10^3\;J/mol{\cdot}kg$ with increasing concentration, respectively. Storage (G') and loss (G") moduli were generally increased with increasing frequency. For the 70% ethanol concentrates, G" predominated over G' at all applied frequencies and so they showed the typical flow behavior of a low molecular solution. However, for the hot water concentrates, G' predominated over G" at more than 1.9 rad/sec (cross-over point) and so they showed the typical flow behavior of a macromolecular solution.

• Korean Journal of Food Science and Technology
• /
• v.35 no.2
• /
• pp.188-194
• /
• 2003

천마식품가공시 기초자료로 활용될 수 있는 천마 추출농축액의 리올로지 특성을 조사하였다. 천마의 열수 및 50% 에탄올 추출물운 각각 5, 10, 15, 및 20 Brix와 10, 20, 30, 40 및 50 Brix로 농축하여 제조하였다. 열수 및 50% 에탄올 농축액의 정상유동특성과 동적점탄성을 조사하였다. Power law model로 구한 n에 의하면 모든 열수 농축액들은 전형적인 의가소성$(n=0.484{\sim}0.802)$유체의 흐름특성을 보였고, 50% 에탄올 농축액들은 뉴튼유체$(n=0.875{\sim}1.078)$에 가까운 흐름특성을 나타내었다. 열수 및 50% 에탄올 농축액의 ${\eta}_{app}$는 온도가 증가함에 따라 감소하는 경향을 나타내었다. Herschel-Bulkley model에 의한 열수 및 50% 에탄올 농축액의 C는 각각 $0.030{\sim}1.255$ Pa와 $0.007{\sim}0.065$ Pa이었다. ${\eta}_{app}$에 대한 온도 및 농도의 영향은 arrhenius식으로 해석하였다. 열수 및 50% 에탄올 농축액의 $E_a$는 농도가 증가함에 따라 각각 $3.340{\sim}4.620{\times}10^3\;J/mol{\cdot}kg$과 $1.6289{\sim}18.6699{\times}10^3\;J/mol{\cdot}kg$의 범위로 나타났다. 진동수(angular frequency, ${\omega}$)가 증가할수록 저장탄성률(storage modulus, G#)과 손실탄성률(loss modulus, G@)은 일반적으로 증가하는 경향을 나타냈다. 50% 에탄올 농축액의 경우 모든 진동수에서 G#이 G@보다 높게 나타나 전형적인 저분자용액의 흐름특성을 보였다. 그러나 열수농축액의 경우 G@이 G#보다 높았고 0.5 rad/sec에서 교차점을 형성하였으며 전형적인 고분자 용액의 흐름특성을 나타내었다.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.4
• /
• pp.844-851
• /
• 2010

Controlling the dissolved oxygen (DO) in the fed-batch culture of the medicinal mushroom Ganoderma lucidum led to a 2-fold increase of the maximum biomass productivity compared with uncontrolled DO conditions. By contrast, extracellular polysaccharide (EPS) production was two times higher under oxygen limitation (uncontrolled DO) than under increased oxygen availability (controlled DO). Morphologically, dispersed mycelium was predominant under controlled DO conditions, with highly branched hyphae, consistent with the enhanced culture growth noted under these conditions, whereas in the uncontrolled DO process mycelial clumps were the most common morphology throughout the culture. However, in both cultures, clamp connections were found. This is an exciting new finding, which widens the applicability of this basidiomycete in submerged fermentation. In rheological terms, broths demonstrated shear-thinning behavior with a yield stress under both DO conditions. The flow curves were best described by the Herschel-Bulkley model: flow index down to 0.6 and consistency coefficient up to 0.2 and 0.6 Pa $s^n$ in uncontrolled and controlled cultures DO, respectively. The pseudoplastic behavior was entirely due to the fungal biomass, and not to the presence of EPS (rheological analysis of the filtered broth showed Newtonian behavior). It is clear from this study that dissolved oxygen tension is a critical process parameter that distinctly influences G. lucidum morphology and rheology, affecting the overall performance of the process. This study contributes to an improved understanding of the process physiology of submerged fermentation of G. lucidum.

• Journal of Pharmaceutical Investigation
• /
• v.39 no.3
• /
• pp.185-199
• /
• 2009

Using a strain-controlled rheometer [Advanced Rheometric Expansion System (ARES)], the steady shear flow properties and the dynamic viscoelastic properties of $Antiphlamine-S^{(R)}$ lotion have been measured at $20^{\circ}C$ (storage temperature) and $37^{\circ}C$ (body temperature). In this article, the temperature dependence of the linear viscoelastic behavior was firstly reported from the experimental data obtained from a temperature-sweep test. The steady shear flow behavior was secondly reported and then the effect of shear rate on this behavior was discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters. The angular frequency dependence of the linear viscoelastic behavior was nextly explained and quantitatively predicted using a fractional derivative model. Finally, the strain amplitude dependence of the dynamic viscoelastic behavior was discussed in full to elucidate a nonlinear rheological behavior in large amplitude oscillatory shear flow fields. Main findings obtained from this study can be summarized as follows : (1) The linear viscoelastic behavior is almostly independent of temperature over a temperature range of $15{\sim}40^{circ}C$. (2) The steady shear viscosity is sharply decreased as an increase in shear rate, demonstrating a pronounced Non-Newtonian shear-thinning flow behavior. (3) The shear stress tends to approach a limiting constant value as a decrease in shear rate, exhibiting an existence of a yield stress. (4) The Herschel-Bulkley, Mizrahi-Berk and Heinz-Casson models are all applicable and have an equivalent validity to quantitatively describe the steady shear flow behavior of $Antiphlamine-S^{(R)}$ lotion whereas both the Bingham and Casson models do not give a good applicability. (5) In small amplitude oscillatory shear flow fields, the storage modulus is always greater than the loss modulus over an entire range of angular frequencies tested and both moduli show a slight dependence on angular frequency. This means that the linear viscoelastic behavior of $Antiphlamine-S^{(R)}$ lotion is dominated by an elastic nature rather than a viscous feature and that a gel-like structure is present in this system. (6) In large amplitude oscillatory shear flow fields, the storage modulus shows a nonlinear strain-thinning behavior at strain amplitude range larger than 10 % while the loss modulus exhibits a weak strain-overshoot behavior up to a strain amplitude of 50 % beyond which followed by a decrease in loss modulus with an increase in strain amplitude. (7) At sufficiently large strain amplitude range (${\gamma}_0$>100 %), the loss modulus is found to be greater than the storage modulus, indicating that a viscous property becomes superior to an elastic character in large shear deformations.