• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.21-30
• /
• 2005

The aerodynamic analysis of helicopter rotor airfoils was performed to generate the basic data for selection and distribution of airfoils at the helicopter rotor blade preliminary design phase.10 airfoils were chosen among the existing rotor airfoils, and the tabulated aerodynamic coefficients which are proper for the aerodynamic analysis using blade element theory were generated. Considering analysis cost, the simple mathematical models were chosen before the wind tunnel test to generate the aerodynamic characteristic curves($C_{l},C_{m},C_{d}$) in full AoA range($-180^{o}\sim180^{o}$) including the reverse flow region. The essential data necessary to the generation of the complete curves were obtained by using the IBLM(Interactive Boundary Layer Method). The generated aerodynamic characteristic curves agree with experimental results qualitatively. Finally, the aerodynamic characteristics of all 10 airfoils were compared and classified according to their own lift or moment characteristics.

• Composites Research
• /
• v.32 no.4
• /
• pp.191-198
• /
• 2019

The basic mechanical properties of helicopter rotor blade are important parameters for the analysis of helicopter performance. However, it is difficult to estimate these properties because the most of rotor blades consist of various materials such as composite materials and metals, etc. In this paper, the bending/torsional stiffness for composite rotor blade of unmanned helicopter were evaluated through experimental and analytical studies. In finite element analysis, the bending/torsional stiffness were evaluated through the relationship of load-displacement and element stiffness matrix. The evaluated stiffness from the measured strains and displacements in bending and torsional test agreed well with the derived results of FEA.

• Journal of computational fluids engineering
• /
• v.16 no.4
• /
• pp.21-27
• /
• 2011

In this paper, the diagonal implicit harmonic balance method is applied to analyze helicopter rotor blade flow. The periodic boundary condition for Fourier coefficients is also applied in hover and forward flight conditions. It is available enough to simulate the forward flight problem with only one rotor blade using the periodic boundary condition in the frequency domain. In order to demonstrate the present method, Caradonna & Tung's rotor blades were used and the results were compared to the time-accurate method and experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.543-549
• /
• 2011

In this paper, diagonal implicit harmonic balance method is applied to analyze helicopter rotor blade flow. Periodic boundary condition for Fourier coefficients is also applied in hover and forward flight condition. It is available enough to simulate the forward flight problem with only one rotor blade using the periodic boundary condition in frequency domain. In order to demonstrate present method Carodonna & Tung's rotor blades are used and the results are compared to time-accurate method and experimental data.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.7
• /
• pp.539-547
• /
• 2021

Helicopter rotor blade is required to be designed by considering the interacting effects among aerodynamics, flexibility, and controllability. The reverse design allows the structural components to have common characteristics by using the configuration numerics and experimental results. This paper aims to design the composite rotor blade which will feature common characteristics with that of BO-105. The present engineering design procedure is done by dividing the rotor blade into a few sections and composite laminates across the cross section. For each section, variational asymptotic beam sectional analysis (VABS) program is used to evaluate its flapwise, lagwise, and torsion stiffnesses to have discrepancy smaller than certain tolerance. Finally, CAMRAD II is used to predict the stress acting on the rotor blade during the specific flight condition and to check whether the present deign is structurally valid.

• International Journal of Aeronautical and Space Sciences
• /
• v.9 no.2
• /
• pp.48-57
• /
• 2008

The noise is one of the serious problems concerning helicopters operations. The issue of helicopter external noise generated mainly from a helicopter rotor has always affected the use of rotorcrafts, especially in the urban environment. The noise sources depend on the flight configurations. In particular, a noise generated by the interaction between blades and tip vortices mainly occurs during descent flight. This noise is called blade-vortex interaction (BVI) noise, and this BVI noise is particularly penalizing for helicopters. In this paper, a numerical study to capture the BVI noise is carried out. The numerical study is performed in two phases. In the first phase, a 2D simulation based on parallel BYI event of Kitapliglu et al experiment is performed. In the second phase, 3D simulation based on HART Ⅱ experiment is performed. Several experimental data such as thrust, torque, blade sectional load, its derivative and vortex location are compared with calculation results and the comparison showed reasonably good agreement.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.183-189
• /
• 2016

In this paper, an optimization study on a helicopter rotor blade cross-section was made. Generalization was made to the baseline cross-section to simplify the analysis. To have better performance in aeroelastic response, with the aerodynamic center being the origin of the baseline, the distance between aerodynamic center and shear center, and the distance between mass center and shear center of the blade were minimized. For efficient searching of optimum solutions over the design space, grid search method, which is a method of graphical search was used. Two design variables, radius of balancing weight at leading edge, and offset of the spar from leading edge were selected for the study. Cubic spline interpolation method was used to accommodate searching of the optimum solution. 2-Leveled searching system was devised in accordance with the interpolation method. Optimum solution was found to show 6% decrease in both distance between aerodynamic center and shear center, and mass center and shear center to the baseline.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.638-642
• /
• 2008

Computational methods based on the solution of the flow model are widely used for the analysis of lowspeed, inviscid, attached-flow problems. Most of such methods are based on the implementation of the internal Dirichlet boundary condition. In this paper, the time-domain panel method uses the piecewise constant source and doublet singularities. The present method utilizes the time-stepping loop to simulate the unsteady motion of the rotary wing blade. The wake geometry is calculated as part of the solution with no special treatment. To validate the results of aerodynamic characteristics, the typical blade was chosen such as, Caradonna-Tung blade and present results were compared with the experimental data and the other numerical results in the single blade condition and two blade condition. This isolated rotor blade model consisted of a two bladed rotor with untwisted, rectangular planform blade. Computed flow-field solutions were presented for various section of the blade in the hovering mode.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.39-42
• /
• 2008

In the case of the general helicopter among rotorcraft, length of the rotor blade for thrust-generation is longer than that of fuselage and tail rotor is required in order to compensate moment of the fuselage. For those reasons, enough space for take-off and landing should be secured and an accessibility for building is low. Also, the accidents caused by tail rotor occur frequently. However, the case of counter-rotating has merits that tail rotor is unnecessary as well as length of the rotor blade can be shortened but has a weakness that the weight of body is increased. In the present study, aerodynamic force measurement on single rotor system equipped with NACA0012 airfoil, which has aspect ratio of 6 and chord length of 35.5 mm, was carried out. And measurement was conducted with blade which has a half size of the former blade by using single motor counter-rotating. Aerodynamic force measurement was acquired by using 6-component balances and coefficients of thrust and power were derived along the pitch angle varying from 0$^{\circ}$ to 90$^{\circ}$ with the increment of 10$^{\circ}$. Those aerodynamic force data will be utilized for the design and production of brand-new counter-rotating rotor blade system which has same thrust with single blade system and provides a good accessibility to building by reducing its blade length.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.71-74
• /
• 2012

Generally, tone noise is generated at the rotary wing and helicopter. BVI(Blade-Vortex Interaction) noise is one of the helicopter's tone noise. The BVI noise is governed by tip-vortex characteristics such as vortex size, strength and trajectory. To avoid BVI, many methods have been developed and proposed. In this paper, rotating blade with active tab was numerically investigated to reduce BVI noise. For flow and noise simulation, the lifting surface approach and the acoustic analogy were used. Using numerical methods, the noise directivity and maximum noise position were predicted.