• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.233-241
• /
• 2003

Geotextile tube is hydraulically filled with dredged materials and has been applied to coastal protection and scour protection, dewatering method of slurry, and isolation of contaminated material. Recently, geotextile tube technology is no longer alternative construction technique but suitable desired solution. In this paper, the numerical analysis was performed to investigate the behavior of geotextile tube with various properties of geotextile sheet and hydraulic pumping conditions. Numerical analysis was executed to compare with the results from the large-scale field model tests, and also with those of plane strain analysis and 3-D FEM analysis. A geotextile tube was modeled using the commercial finite element analysis program ABAQUS and the one-quarter of tube was modeled. Behavior of geotextile tube during the hydraulic pumping procedure was analyzed by comparing the large-scale field model test and numerical analysis. The shape variation and maximum tube height between the numerical analysis results and large-scale filed test results are turned out to be in a good agreement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.572-577
• /
• 2001

The electrical properties of Pr$_{6}$ O$_{11}$ -based ZnO varistors consisting of ZnO-Pr$_{6}$ O$_{11}$ -CoO-Cr$_2$O$_3$-Er$_2$O$_3$ ceramics were investigated with sintering temperature in the range of 1325~f1345$^{\circ}C$. As sintering temperature is raised., the nonlinear exponent was increased up to 1335$^{\circ}C$, reaching a maximum 70.53, whereas raising sintering temperature further caused it to decrease, reaching a minimum 50.18 and the leakage current was in the range of 1.92~4.12 $\mu$A. The best electrical properties was obtained from the varistors sintered at 1335$^{\circ}C$, exhibiting a maximum (70.53) in the nonlinear exponent and a minimum (1.92 $\mu$A) in the leakage current, and a minimum (0.035) in the dissipation factor. On the other hand, the donor concentration was in the range of (0.90~1.14)x10$^{18}$ cm$^{-3}$ , the density of interface states was in the range of (2.69~3.60)x10$^{12}$ cm$^{-2}$ , and the barrier height was in the range of 0.77~1.21 eV with sintering temperature. With raising sintering temperature, the variation of C-V characteristic parameters exhibited a mountain type, reaching maximum at 134$0^{\circ}C$. Conclusively, it was found that the V-I, C-V, and dielectric characteristics of Pr$_{6}$ O$_{11}$ -based ZnO varistors are affected greatly by sintering temperature.

• Journal of Ecology and Environment
• /
• v.35 no.2
• /
• pp.111-122
• /
• 2012

The sex ratio and spatial structure of different sexes are major components that affect the reproductive success and population persistence of dioecious plants. The differential reproductive costs between male and female plants are often believed to cause a biased sex ratio and spatial segregation of the sexes through slower growth and/or lower female survivorship. In this study, we examined the sex ratio and spatial structure of one population of $Torreya$ $nucifera$ trees in Jeju Island, Korea. We also tested the effects of the current tending actions in relation to tree vitality. At the population level, the sex ratio of the 2,861 trees was significantly biased toward males; however, it also showed considerable variation among different diameter at breast height classes and across habitats according to terrain level (from upper to lower). In 1999, before tree management (tending) began, among the ecological traits examined, only climber coverage correlated with tree vitality. Intensive tending such as climber removal since 1999 clearly enhanced the vitality of the majority of trees, but its effects were more conspicuous in medium-sized trees than in small ones, in upper terrain trees than those in other terrains, and in females than in males. Both male tree domination in small and large trees and tending effects on females are likely to reflect the effects of female reproductive costs regarding growth and/or survivorship. Spatial segregation between males and females was not observed in $T.$ $nucifera$. Habitat heterogeneity created by the forest's rocky ground and its implications regarding sex ratios and spatial structure require further studies.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1465-1474
• /
• 1994

For a vertical wall with standing waves on its front face, the unsteady flow in a flow conduit installed through the wall is analyzed. A nonlinear standing wave theory making use of Fourier expansion is applied, and the results are verified by a hydraulic experiment. It is found that the nonlinear theory better predicts the behavior of the flow compared to its linear counterpart. The investigation of the water transmissibility through the conduit shows that the variation of the flow rate becomes larger as the standing wave height and period increase and as the length of conduit decreases. The relationship is presented by a nondimensional equation. The net flow gain per one wave period, which is directly related to water exchanging capability of the conduit, appears to be negative in both theory and experiment when the conduit is located near the bottom. The maximal flow gain occurs in the conduit whose mouth is located at the still water level. In addition, it is shown that the longer wave period and the shorter conduit length are more effective in the water exchanging performance.

• Journal of Plant Biotechnology
• /
• v.6 no.4
• /
• pp.205-212
• /
• 2004

The objectives were to compare the salt tolerance levels in the parental rice cultivar, Dongjinbyeo, and induced mutagenesis derived its lines for plant height, MDA, ATPase, POD, and 2-dimensional protein electrophoresis pattern in NaCl-containing hydroponic nutrient solutions. Rice plants isolated from a population of rice (Oryza sativa L. cv. Dongjinbyeo) mutation lines, which were generated in combination with in vitro selection and gamma-ray, exhibited salt tolerance. Line No. 18 had the longest plant, whereas NaCl-sensitive line (No. 25) had the shortest plant. The parent, and the sensitive line showed severe damage from salt stress. Tolerant lines (No. 18, 50) had a lower malonaldehyde (MDA) content than the sensitive one (Dongjinbyeo, No. 25) during salt stress. Several proteins showed significant quantitative variation through 2DE; phosphoribulokinase, peroxidase, oxygen evolving enhancer 1 and the $H^+-ATPase$, which are known to be involved in salt tolerance. The effect of salt on peroxidase and $H^+-ATPase$ activity in the seedlings of two groups with contrasting genotypes of rice was studied. A greater activity was recorded in the tolerant lines as compared to the sensitive ones (P<0.05, Duncan's test). The results indicate that salt tolerant lines expressed more salt stress-inducible proteins associated with salt tolerance than the sensitive lines during salt stress.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.7
• /
• pp.729-738
• /
• 2010

The characteristics of lifted butane flames diluted with nitrogen have been investigated experimentally in order to elucidate the mechanism of individual flame oscillation modes. Flame oscillations in laminar free-jet lift-off flames are classified into the following five regimes: a stabilized lift-off regime (I), a heat-loss-induced oscillation (II), a buoyancy-induced oscillation along with a heat-loss-induced oscillation (III), a combined form of an oscillation prior to blow-out and a heat-loss-induced oscillation (IV), and a combination of an oscillation prior to blow-out and a buoyancy-induced oscillation along with a heat-loss-induced oscillation (V). The characterization of the individual flame oscillations modes are presented and discussed using Strouhal numbers and their relevant parameters by the analysis of the power spectrum for temporal variation of the lift-off height.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.517-523
• /
• 1997

We have been studied that combustion efficiency and the production of air pollution of anthracite-bituminous coal blend in a fluidized bed coal combustor. Also, the reaching time of steady state condition have been studied. This experimental results are presented as follows. As the height of fluidized bed combustor becomes higher, the concentrations of $SO_2$ and NOx mainly increased. Also, as anthracite fraction increased, the emission of $SO_2$ concentration was increased but, the variation of $NO_X$ concentration was negligible according to anthracite fraction. When anthracite fraction ratio was increased, elutriation rate was increased and exit combustible content over feeding combustible content was increased. Regardless of anthracite fraction ratio the uncombustible weight percentage according to average diameter of elutriation particles were approximately high in the case of fine particles. Over bed temperature $850^{\circ}C$ and excess air 20%, the difference of combution at the velocity 0.3m/s, bed temperature $850^{\circ}C$, the excess air 20%.

• Geomechanics and Engineering
• /
• v.19 no.5
• /
• pp.463-472
• /
• 2019

The mode perturbation method (MPM) is suitable and efficient for solving the eigenvalue problem of a nonuniform soil deposit whose property varies with depth. However, results of the MPM do not always converge to the exact solution, when the variation of soil deposit property is discontinuous. This discontinuity is typical because soil is usually made up of sedimentary layers of different geologic materials. Based on the energy integral of the variational principle, a new mode perturbation method, the energy-based mode perturbation method (EMPM), is proposed to address the convergence of the perturbation solution on the natural frequencies and the corresponding mode shapes and is able to find solution whether the soil properties are continuous or not. First, the variational principle is used to transform the variable coefficient differential equation into an equivalent energy integral equation. Then, the natural mode shapes of the uniform shear beam with same height and boundary conditions are used as Ritz function. The EMPM transforms the energy integral equation into a set of nonlinear algebraic equations which significantly simplifies the eigenvalue solution of the soil layer with variable properties. Finally, the accuracy and convergence of this new method are illustrated with two case study examples. Numerical results show that the EMPM is more accurate and convergent than the MPM. As for the mode shapes of the uniform shear beam included in the EMPM, the additional 8 modes of vibration are sufficient in engineering applications.

• Asian-Australasian Journal of Animal Sciences
• /
• v.8 no.5
• /
• pp.515-522
• /
• 1995

The field experiment was carried out to study the growth and fodder yield of the Gliricidia sepium provenances in fence system in dryland farming area in Bali, Indonesia for 24 months. The design of the experiment was a completely randomized block arrangement, consisted of 16 treatments (Gliricidia sepium provenances) and 12 blocks with 10 plants per provenance. Of the 16 gliricidia provenances, six were from Mexico (M), four were from Guatemala (G), and one each was from Colombia (C), Indonesia (I), Nicaragna (N), Panama (P), Costa Rica (R) and Venezuela (V). After 40 weeks establishment the gliricidia were lopped regularly 4 times a year, twice during the four month wet season and twice during the eight month dry season at 150 cm height. There were variations (p < 0.05) in stem elongation from 10 to 121 cm, leaf retained from 48 to 105%, leaf shedding from 53 to 86%, branch number from 4 to 7, fodder yield from 281 to 648 g DW/plant, and wood yield from 53 to 179 g DW/plant; and such variations were affected by the seasons. Retalhuleu provenance of Guatemala (G14), Belen provenance of Nicaragua (N14) and Bukit Bali provenance of Indonesia (I) were ranked first, second and third, respectively, measured in terms of stem elongation, leaf retention, fodder and wood yields during the wet and dry seasons.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.198-201
• /
• 2001

Porous structures of aluminum foam have been studied by using return aluminum scrap. The apparent foam shape, foam height, density, pore size and their distributions in various section areas of the experimental samples have been investigated. The sample have been cast into metallic mold, using aluminum foam prepared from a precursor based on pure Al ingot and return aluminum scrap mixed with various amounts of 1-2wt% increasing viscosity and foam agent materials. The process provides for flexibility in design of foam structures via relatively easy control over the amount of hydrogen evolution and the drainage processes which occur during foam formation. This is facilitated by manipulating parameters such as the foaming agent, thermal histories during solidification and mix melt viscosities. A metal for producing the foamed are decomposing a foaming agent in a molten metal such that there is an initial and a subsequent expansion due to foaming agent. It has been found that the Al porous foaming with variation amount of 1∼2wt% foam agent and at 2min holding time, which melting temperature has appeared homogeneous pore size at 650∼700$^{\circ}C$. The compression strength were 10-13 kg/min at 125ppi, and increased by higher pore density. The acoustical performance of the panel made with the foamed aluminum is considerably improved; its absorption coefficient shows NRC 0.6-0.8. It has been found that the Al foam is very preferable for the compactness of the thermal system.