• Journal of Environmental Science International
• /
• v.28 no.3
• /
• pp.341-356
• /
• 2019

In this study, the impacts of local meteorology caused by tidal changes in the West Sea on ozone distributions in the Seoul Metropolitan Area (SMA) were analyzed using a meteorological model (WRF) and an air quality (CMAQ) model. This study was carried out during the day (1200-1800 LST) between August 3 and 9, 2016. The total area of tidal flats along with the tidal changes was calculated to be approximately $912km^2$, based on data provided by the Environmental Geographic Information Service (EGIS) and the Ministry of Oceans and Fisheries (MOF). Modeling was carried out based on three experiments, and the land cover of the tidal flats for each experiment was designed using the coastal wetlands, water bodies (i.e., high tide), and the barren or sparsely vegetated areas (i.e., low tide). The land cover parameters of the coastal wetlands used in this study were improved in the herbaceous wetland of the WRF using updated albedo, roughness length, and soil heat capacity. The results showed that the land cover variation during high tide caused a decrease in temperature (maximum $4.5^{\circ}C$) and planetary boundary layer (PBL) height (maximum 1200 m), and an increase in humidity (maximum 25%) and wind speed (maximum $1.5ms^{-1}$). These meteorological changes increased the ozone concentration (about 5.0 ppb) in the coastal areas including the tidal flats. The increase in the ozone concentration during high tide may be caused by a weak diffusion to the upper layer due to a decrease in the PBL height. The changes in the meteorological variables and ozone concentration during low tide were lesser than those occurring during high tide. This study suggests that the meteorological variations caused by tidal changes have a meaningful effect on the ozone concentration in the SMA.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.531-552
• /
• 2020

In the previous study, both the wave characteristics at the tip of composite breakwater and on caisson were investigated by applying olaFlow numerical model of three-dimensional regular waves. In this paper, the same numerical model and layout/shape of composite breakwater as applied the previous study under the action of one directional irregular waves were used to analyze two and three-dimensional spatial change of wave force including the impulsive breaking wave pressure applied to trunk of breakwater, the effect of rear region, and the occurrence of diffracted waves at the tip of caisson located on the high crested rubble mound. In addition, the frequency spectrum, mean significant wave height, mean horizontal velocity, and mean turbulent kinetic energy through the numerical analysis were studied. In conclusion, the larger wave pressure occurs at the front wall of caisson around the still water level than the original design conditions when it generates the shock-crushing wave pressure in three-dimensional analysis condition. Which was not occurred by two-dimensional analysis. Furthermore, it was confirmed that the wave pressure distribution at the caisson changes along the length of breakwater when the same significant incident wave was applied to the caisson. Although there is difference in magnitude, but its variation shows the similar tendency with the case of previous study.

• Physical Therapy Korea
• /
• v.12 no.4
• /
• pp.41-47
• /
• 2005

The purpose of this study was to determine the intra-rater and inter-rater reliability of various forward head posture measurements. Ten healthy adults (age, $20.4{\pm}2.2$ yrs; height, $164.0{\pm}5.5$ cm; weight, $58.7{\pm}7.3$ kg) participated in the study. They were free of injury and neurologic deficits in the upper extremities and neck at the time of testing. The subjects were asked to perform head forward posture by under the guidance of physical therapists. Markers were placed on the C7 spinous process, mastoid process, tragus of the ear, outer canthus, and forehead. Measurement 1 for forward head posture assessment was measured as the angle between the horizontal line through C7 and the line connecting the C7 spinous process with the tragus of the ear. Measurement 2 was measured as the angle between the C7 spinous process, the mastoid process and the outer canthus. Measurement 3 was measured as two kinds of angles the HT (head tilt) angle is between the line from the midpoint of forehead to the tragus line and Y-axis at the tragus point. The NF (neck flexion) angle is between the line from the tragus to the C7 line and the Y-axis at the C7. Intra-rater, inter-rater reliability and coefficient of variation was assessed by comparing the measured values from three kinds of measurements of forward head posture. The intra-rater reliability was indicated by intraclass correlation coefficients [ICC(1,1)] and inter-rater reliability was shown by intraclass correlation coefficients [ICC(3,k)]. The results of study were as follows: ICC(1,1) values for intra-rater reliability of three measurements were in the 'excellent' category. ICC(3,k) values for inter-rater reliability of three measurements were also in the 'excellent' category. The coefficient of variation of method 2 had a lower value than method 1 and method 3. This data means that the measured value of method 2 was less scattered. Further research is needed to determine whether the validity of all measurements is revealed in the 'excellent' category.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.11
• /
• pp.1738-1745
• /
• 2007

A growth trial and a digestibility trial were conducted to examine the effect of feed particle size on the performance, nutrient digestibility, gastric ulceration and intestinal morphology in pigs fed barley-based diets. Barley was processed through a hammer mill to achieve four diets varying in particle size (average particle $size{\pm}standard $deviation): coarse ($1,100{\pm}2.19\;{\mu}m$), medium ($785{\pm}2.23\;{\mu}m$), fine ($434{\pm}1.70\;{\mu}m$) and mixed (1/3 of coarse, medium and fine) ($789{\pm}2.45\;{\mu}m$). Sixty-four entire male pigs were used in the growth trial and the diets were fed ad libitum between 31 kg and 87 kg live weight. Following slaughter, stomach and ileal tissues were scored for integrity (ulceration or damage) and histological measurements taken. Twenty-four entire male pigs were used in the digestibility trial, which involved total faecal collection. Over the entire growth phase, there were no differences (p>0.05) in average daily gain and feed conversion ratio between pigs fed diets of different particle size. Pigs fed the coarse and medium diets had lower (p<0.05) stomach ulceration scores (0.20 and 0.25, respectively, on a scale from 0 to 3) than those fed the mixed (0.69) or the fine diets (1.87). The stomachs of all animals fed the fine diet had lesions and stomach ulcerations were present only in this group. Pigs fed the fine diet had thicker (p<0.001) ileal epithelial cell layer with no differences (p>0.05) being observed for villous height or crypt depth. Faecal digestibility coefficients of neutral and acid detergent fibre were the highest (p<0.05) for the mixed diet, intermediate for the fine and coarse diets and the lowest for the medium diet. A similar numerical trend (p = 0.103) was observed for the apparent faecal energy digestibility coefficient. It is concluded that, with barley based diets, a variation in average particle size between $400{\mu}m$ and $1,100{\mu}m$ had no effect on pig performance but the fine dietary particle size affected the integrity of the stomach, as well as the structure of the small intestine, thus compromising overall gut health. Our data also demonstrate that changes in particle size distribution during the digestion process, rather than average particle size or particle size variation, are related to apparent faecal digestibility.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.21 no.2
• /
• pp.24-33
• /
• 2018

DSM and orthoimage, which are representative results of UAV photogrammetry, are high-quality spatial information data and are widely used in various fields of spatial information industry in recent years. However, the UAV photogrammetry has a problem that the quality of the output of the UAV deteriorates due to the altitude of the UAV, the camera calibration, the weather conditions at the time of shooting, the performance of the GPS / IMU and the number of the ground reference points. The purpose of this study is to analyze the location accuracy of unmanned aerial photogrammetry according to the change of the number if ground control points. Experiments were made with fixed wing, and the shooting altitude was set at 130m and 260m. The number of ground reference points used was 9, 8, 5, and 4, respectively. Ten checkpoints were used. XY RMSE for orthoimage and Z RMSE for DSM were compared and analyzed. In addition, the resolution of the orthoimage was determined to affect the judgment of the operator in the verification of the planimetric position accuracy, and the visual resolution was analyzed using the Siemens star target. As a result of the analysis, the variation of the vertical position accuracy is larger than the variation of the planimetric position accuracy when the number of the ground reference points are different. Also The higher the flying height, the greater the effect of change of ground control points on position accuracy.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.79-85
• /
• 2011

Bridge Weigh-in-Motion(BWIM) system calculates a travelling vehicle's weight without interruption of traffic flow by analyzing the signals that are acquired from various sensors installed in the bridge. BWIM system or data accumulated from the BWIM system can be utilized to development of updated live load model for highway bridge design, fatigue load model for estimation of remaining life of bridges, etc. Field test with moving trucks including various load cases should be performed to guarantee successful development of precise BWIM system. In this paper, a numerical simulation technique is adopted as an alternative or supplement to the vehicle traveling test that is indispensible but expensive in time and budget. The constructed numerical model is validated by comparison experimentally measured signal with numerically generated signal. Also vehicles with various dynamic characteristics and travelling conditions are considered in numerical simulation to investigate the variation of bridge responses. Considered parameters in the numerical study are vehicle velocity, natural frequency of the vehicle, height of entry bump, and lateral position of the vehicle. By analyzing the results, it is revealed that the lateral position and natural frequency of the vehicle should be considered to increase precision of developing BWIM system. Since generation of vehicle travelling signal by the numerical simulation technique costs much less than field test, a large number of test parameters can effectively be considered to validate the developed BWIM algorithm. Also, when artificial neural network technique is applied, voluminous data set required for training and testing of the neural network can be prepared by numerical generation. Consequently, proposed numerical simulation technique may contribute to improve precision and performance of BWIM systems.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.22 no.2
• /
• pp.193-202
• /
• 1998

The purpose of this study was to understand clothing condition of elderly men focusing on somatotype variation and satisfaction with ready-to-wear and to provide basic data in designing ready-to-wrar for the elderly men. The questionnaire method was used and one-to-one interviews were held for the elderly residents in Seoul, Deajon, Jonju, and Yeosu areas. The total of 275 questionnaires (from 148 elderly men in the 60's, 99 in the 70's and 28 in the 80's) were collected and used for statistics. SAS package was used for the statistics and the statistics were based on frequency, X2-test, ANOVA, Duncan's multifle range test. The results of the study were as follows; 1) Height (p< .05), weight (p< .001) and Rohrer index (p< .05) decreased significantly with ageing 2) The somatotypes of 75.6% were changed and the 70's 8t the 80's showed significantly (p< .05) higher changing rate compared to the 60's and more changes took place significantly (p< .001) with ageing. 3) The most preferred out wear was suit & tie and next was jumper or shirt. 4) For the mode of getting suit, the highest number 55.3%) purchased ready-to-wear, next (32.0%) was tailored and the least (12.7%) neither purchased nor tailored. The percentage of buying ready-to-wear significantly (p< .01) decreased with ageing. The main reason for getting tailor-made was not well fitting of ready-to-wear (20.7% out of 32.0%). And for the mode of getting suit, there was significant differance with income (p< .001) and pocket money (p< .01). 5) The most important factors in suit and shirt werefirst, size (fitness) and second, comfort in movement. 6) For the wearing feeling of suit, 55.3% showed discomfort. There was significant difference according to the age (p< .05) and pocket money (p< .05). The Discomfort increased with ageing and less pocket money. 7) 62.4% answered it uneasy to Pick out well fitting If comfortable suit. This showed their dissatisfaction with ready-to-wear. 8) As for the items of not well fitting, 64.4% answered in jacket, 60.8% in trousers, 46.0% in shirt. The above result shows that elderly men's somatotype changes as they age, suit is found uncomfortable and it's not easy for elders to pick out comfortable ready-to-wear. So, they seem to have a certain dissatisfaction in ready to wear. Therefore, there is a need for reorganization of size and developing pattern design according to measurement of elderly men.

• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.6
• /
• pp.550-561
• /
• 2009

This study is to investigate the air pollution characteristics of an industrialized midsize west-coastal city by comparing air quality to a neighboring inland city. The hourly averaged data of $O_3$, $SO_2$, $NO_2$, CO, and $PM_{10}$ measured from continuous air quality monitoring sites in Gunsan (coastal) and Jeonju (inland) were analyzed. The data set covers the period from 2004 to 2006. The annual average concentrations of the air pollutants in two cities were compared in their abundances and temporal trends as well. $O_3$ and $SO_2$ in Gunsan were relatively higher than those in Jeonju, while vice versa in case of $NO_2$ and $PM_{10}$. It seems that heavy automobile emissions from Jeonju mainly bring on higher $NO_2$ and $PM_{10}$ than those in Gunsan on annual base. $NO_2$ concentrations in both cities showed bimodal diurnal variations with peaks in the morning and in the late evening. These peaks correspond to the coupled effects of rush hour traffic and meteorological conditions (i.e., variation of mixing height and dispersion conditions). Maximum hourly averages of $NO_2$ ranged from 18 ppb to 28 ppb at Jeonju, and from 12 ppb to 20 ppb at Gunsan. $O_3$ showed typical diurnal variation with a maximum in the afternoon between 14:00 and 16:00 LST. Diurnal variations of CO and $PM_{10}$ were similar to $NO_2$ while $SO_2$ was similar to $O_3$. Seasonal variations of $PM_{10}$ in both cities indicated that their concentrations during spring season were significantly high. Asian dust storms occur frequently during spring and seem to affect increase in $PM_{10}$. High $O_3$ and $PM_{10}$ days were selected from both cities. The analyses based on the HYSPLIT trajectory model during the high $O_3$ and $PM_{10}$ showed these episodes (six cases) were mostly coincident with Asian dust storm originated from northern China and Mongolia. However, these high air pollution episodes in the west coastal cities may not only be caused by the Asian dust but also affected by other air pollutants transported from China accompanying the Asian dust.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.349-358
• /
• 2010

This study was carried out to investigate the optimum condition for sap exudation of Acer mono Max. tree in a site of Mt. Jiri, Hamyang-gun, Korea. Amount of sap exudation, air temperature, relative air humidity, tree diameter at breast height (DBH) and sugar content in sap were monitored during the early springtime, and correlation analysis of several factors was carried out to explain tree-to-tree and date-to-date variations in sap exudation. The correlation, linearlyassociated between DBH and sap amount, was strengthened as daily amount of sap increased, but there was no significant tree-to-tree variation in time and period for sap exudation. When amount of sap exudation was above 10 liter/day, the mean air-temperature was averaged at $1.2{\pm}1.6^{\circ}C$, the minimum at $-4.3{\pm}1.5^{\circ}C$ and the maximum at $11.8{\pm}1.9^{\circ}C$. The maximum air temperature and mean air temperature were significant (p < 0.05) factors for amount of sap in correlation analysis to explain date-to-date variation in sap exudation. Sucrose content in sap was in the range of 1.5 and 1.7% during exudation days, but sharply reduced to 0.6% level at the end of exudation period.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.3
• /
• pp.179-186
• /
• 2009

Relation between soil salinity and forage yield of five upland crops such as sudan grass, sesbania, barnyard grass, corn and soybean was studied in the three reclaimed lands of Korea during two years from 2007 to 2008. Although plant number emerged was obtained satisfactory by desalting treatment, further growth of crops was sharply affected by re-salting process according to soil drying. Soil salinity varied place by place and changed constantly, crop growth was differently responded to soil salinity according to the specific conditions of the reclaimed lands. In the Iweon reclaimed land with higher soil water conductivity and sandy soil texture, crop growth and yield sharply decrease with increase of soil salinity. Relation between soil salinity and crop growth and yield was well expressed as logarithmic function. Surface soil EC to reach at 50% of growth reduction to the tallest height of crops was $5dS\;m^{-1}$ for soybean, $6dS\;m^{-1}$ for corn and $7dS\;m^{-1}$ for sudan grass, sesbania, and barnyard grass by logarithmic function. In the Hwaong and Yeongsangang reclaimed lands with low soil conductivity and finer soil texture, plant growth response to salt stress was statistically vague by mixing of harmful influence from flooding and wet injury. However, it is observed that crop growth and yield on the place of lower salinity was better than crop growth on the place of higher salinity. It is accordingly concluded that flooding control during summer rainy season is vary important as well as desalting process for good growth of soiling and forage crops in the newly reclaimed land from tidal flat.