• 한국분무공학회지
• /
• 제24권4호
• /
• pp.163-170
• /
• 2019

In this study, feedback logic using dual O₂ sensor values were developed to increase the purification capability of a three-way catalyst (TWC) in a compressed natural gas (CNG) engine. A heavy-duty inline 6-cylinder engine was used and the CNG was supplied to the engine through a mixer. This study consists of two main parts, namely, the proportional integral (PI) control with a front O₂ sensor and the feedback control with dual O₂ sensors. In the PI control experiment, effects of various parameters, such as P gain, I gain, and lean delay, on the TWC capability were identified. Based on the results of the PI control experiment, the feedback logic using dual O₂ sensor values were developed. In both cases, the nitrogen oxides (NO_X) emissions were nearly zero. However, the carbon monoxide (CO) emissions were reduced significant in the feedback logic with dual O₂ sensors than in the PI control with the front O₂ sensor.

• 드라이브 ㆍ 컨트롤
• /
• 제20권4호
• /
• pp.155-156
• /
• 2023

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.78-83
• /
• 2011

Natural gas is one of the most promising alternatives to gasoline and diesel fuels because of its high thermal efficiency and lower harmful emissions, including $CO_2$. Although the high octane value of natural gas increases engine output and efficiency due to the high compression ratio, this fuel is prone to such difficulties as a narrow limit of inflammability and a slow combustion speed in the lean burn operation domain, leading to unstable combustion and higher emissions of harmful exhaust gases. Hydrogen blended with natural gas can extend the lean burn limit while maintaining stable, efficient combustion and achieving lower NOx, hydrocarbon and green house gas emissions. In this study, the effect of hydrogen addition on an engine performance and NOx emission characteristics was investigated in a heavy duty natural gas engine. The results showed that thermal efficiency was increased and NOx emissions were reduced due to the expansion of lean operation range under stable operation. NOx emission can be significantly reduced with the retard of spark advance timing.

• 한국가스학회지
• /
• 제13권1호
• /
• pp.28-33
• /
• 2009

천연가스는 전세계적으로 매장량이 풍부하며 청정성과 경제성을 동시에 갖춘 연료로써 향후 자동차용 연료로 널리 사용될 전망이다. 천연가스를 사용하는 엔진의 출력 및 배출가스 특성을 최적화하기 위해서는 연료량 제어가 필수적이며 이를 위해서는 분사기의 성능이 매우 중요하다. 본 연구에서는 대형 가스엔진에 고유량을 공급할 수 있는 가스분사기를 직접 개발하여 실제 엔진에 장착하여 기존의 고유량 가스분사기와 성능을 비교하였다. 본 연구에서 개발한 가스분사기는 듀티 증가에 따라 선형적인 유량 특성을 지니고 있음을 파악하였으며 이를 통해 분사량 제어성이 우수하다는 것을 확인하였다. 또한 듀티 10% 미만의 조건에서도 분사유량은 선형성을 지니고 있으며 제어성도 우수하다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.199.2-199.2
• /
• 2010

Biodiesels are well-known as alternative fuels. also we know that biodiesels increase NOx and reduce PM(Particulate Matter) by previous many studies. But PM in most these studies was considered about the mass. In this study, We have performed experimental test for PM and exhaust emission by mixed ratio of biodiesel in heavy duty diesel engine. PM was investigated by The nano particle number and the mass. The mass of PM was evaluated by using the standard gravimetric method, The number of PM was evaluated by using the EEPS(Engine Exhaust Particle Sizer), on the ESC(European Steady Cycle) mode. Sampled gas through dilutor was directly extracted from tail pipe and EEPS measured diluted exhaust gas. Biodiesel is made up of used cooking oil. Diesel as base fuel was sold on market and contains 2% biodiesel. The mass of PM was reduced 10% and the nano particle number was increased 5%. The particle number less than 40nm was increased, but the particle number more than 40nm is decreased.

• 동력기계공학회지
• /
• 제17권6호
• /
• pp.130-135
• /
• 2013

It is a research about the change in reduction efficiency and performance resulting from installation of the EGR cooler, which is the core technology reducing NOx in response to standards been tightened of exhaust controls for off-road vehicle. It can reduce NOx by altering combustion temperature and oxygen concentration by recycling high-temperature exhaust gas. The target engine was large diesel engine for construction machine through by which we were able to verify a rate of change in output and capabilities for a heat-exchange within cooler itself depending on the existence of EGR cooler system. We have acquired a emission reduction technology for a construction machine by testing the reduction performance and rate of change in output.

• 한국가스학회지
• /
• 제14권4호
• /
• pp.12-17
• /
• 2010

자동차 연료로서의 천연가스는 고옥탄가, 넓은 연소 한계, 낮은 미연탄화수소 배출 특성, 지구 온난화 물질인 $CO_2$배출 저감 등 디젤과 가솔린을 대신할 수 있는 현실성 있는 대체연료이다. 그러나 희박운전 영역에서는 느린 연소속도 등으로 연소가 불안정해지고 유해 배기가스가 증가하는 단점이 있다. 수소의 첨가는 연소속도를 빠르게 하고 가연한계를 확장시켜 초희박 영역에서도 안정된 운전을 가능하게 하며, NOx의 저감에 유리하다. 본 연구에서는 대형 수소-천연가스 혼합연료 엔진에서 수소 첨가에 따른 기본 연소특성과 희박영역 확장, 배기성능 및 효율 특성에 대해 검토하였다.

• 연구논문집
• /
• 통권33호
• /
• pp.5-16
• /
• 2003

Fuel distribution, combustion, and flame propagation characteristics of heavy duty engine with the liquid phase LPG injection(LPLI) were studied in a single cylinder engine. Optically accessible single cylinder engine and laser diagnostics system were built for quantifying fuel concentration by acetone PLIF(planar laser induced fluorescence) measurements. In case of Otto cycle engine with large bore size, the engine knock and thermal stress of exhaust manifold are so critical that lean burn operation is needed to reduce the problems. It is generally known that fuel stratification is one of the key technologies to extend the lean misfire limit. The formation of rich mixture in the spark plug vicinity was achieved by open valve injection. With higher swirl strength(Rs=3.4) and open valve injection, the cloud of fuel followed the flow direction and the radial air/fuel mixing was limited by strong swirl flow. It was expected that axial stratification was maintained with open-valve injection if the radial component of the swirling motion was stronger than the axial components. The axial fuel stratification and concentration were sensitive to fuel injection timing in case of Rs=3.4 while those were relatively independent of the injection timing in case of Rs2.3. Thus, strong swirl flow could promote desirable axial fuel stratification and, in result, may make flame propagation stable in the early stage of combustion.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.213-218
• /
• 1997

CNG dual fuel engine for heavy duty diesel engine has been equipped to a Korean bus engine and tested to compare th engine performance and the emission characteristics with the existing diesel fueled engine. The results are summarized as follows. Diesel fueled engine has the fuel injection timing of BTDC17°. The injection timing of CNG modified engine is retarded to BTDC14° for reduction of NOx. Performance optimization has been carried out to have engine power equivalent to or better than the diesel fueled engine. Smoke is decreased by 85% by Korean smoke 3 mode test. By 6 mode test CO is increased by 313% and THC is increased by 1407%. NOx is decreased by 27%. Even though THC is increased very much, it's not too serious problem since CO and THC emission of diesel engine are very little compared to gasoline engine and THC don't give bad effect on human health. But the reduction technologies of CO and THC need to be considered.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.42-48
• /
• 2003

LPG has been a broad concern of pro-environmental alternative fuel for vehicles. Recently, the new Liquid Phase LPG Injection(LPLI) system extends the limit of power of LPG engine and gives a chance to substitute LPG engine for diesel engine of heavy duty vehicles that are the main resources of air pollution in urban area. Large bore size of heavy duty LPG engine derives a serious knock problem. To find an optimal MBT conditions, it is necessary to know how the flame develops in the combustion chamber and find where the knock positions are. In this study. the ion-probe head gasket was used to estimate the knock position. Inverse operation of the ion-probe signal provides the flame developing characteristics. The further the position is from the spark plug, the later the flame arrives and the more times knock occurs. The main factor that effects knock position is inferred a flor situation of mixed gas in the combustion chamber.