• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.669-674
• /
• 2006

The optimal control of heat pump performance for heating mode operation was investigated. Fuzzy logic was applied to control the heating performance of heat pump system and superheat at compressor discharge was taken as a control variable. Regression model was adapted to determine the optimal points where COP is maximized. Optimization of fuzzy rule table was investigated to improve operation performance of heat pump system. Experiments were carried out using original fuzzy table and the modified fuzzy rule table for heating mode operation of heat pump system. The results show that control performance of heat pump system with the modified fuzzy rule table was better than that with the original rule table.

• 한국방사선학회논문지
• /
• 제9권3호
• /
• pp.131-137
• /
• 2015

본 연구의 목적은 기존에 사용 중인 X선 발생장치의 촬영대를 따뜻하게 가열하면서도 X선 감약이 적은 탄소나노튜브(carbon nano tube, CNT) 발열체를 사용하여 가열장치를 구비한 X선 발생장치용 부착형 촬영대의 고안 및 설계를 하고자 한다. 고안된 제품의 구성은 부착형 탄소발열체 촬영대로서 기존 X선 촬영대, 탄소나노튜브 면상발열체, 전극선, 난연 처방된 보호필름과 바닥필름으로 구성되어 있다. 본 고안 제품의 특징과 장점은 냉기(冷氣)를 느끼는 촬영대에서 환의를 착용하고 검사를 받는 환자에게 온화한 느낌과 안전감을 제공하고 심적인 불안감을 해소하여 검사에 도움을 줄 수 있기 때문에 임상 적용을 적극 권장하는 바이다.

• International Journal of Ocean System Engineering
• /
• 제3권1호
• /
• pp.38-43
• /
• 2013

Wind turbine generator is, recently, becoming bigger and bigger. So, in order to produce large amounts of electricity generation, we have to consider the length and thickness of the blade. We investigated the skills of processing for making the super thickness laminate through development fabrication process for high speed curing composite heating table.

• 한국가구학회지
• /
• 제23권1호
• /
• pp.68-74
• /
• 2012

In this study domestic thinning and small diameter woods of Giant dogwood (Cornus controversa Hemsl) was used. To increase the utilizability of wood, the utilizability was proposed after manufacturing laminated wood by pressing and heating. The physical and mechanical characteristics of Laminated wood were investigated and the color change was measured, using a Chromaticity coordinates, after being pressed at 10% (45 mm), 20% (40 mm), 30% (35 mm) for 5 minutes, using Stopper, and then heated at $180^{\circ}C$ for 6, 12, 24 and 48 hours. The results were as follows. Wood density, compressive strength, MOR, MOE are increased with increasing pressing rate but decreased as heating time is increased after pressing. However, Color change is clear, dimensional stability is improved after pressing and heating.

• 한국방사선학회논문지
• /
• 제9권4호
• /
• pp.219-225
• /
• 2015

본 연구의 목적은 CR과 DR에서 가열장치를 구비한 부착형 탄소발열체 X선 촬영대의 사용에 따른 SNR과 CNR을 측정하여 부착 전과 부착 후의 화질을 평가하고자 한다. 알루미늄 계단 실험에서 CR은 부착 후에 SNR과 CNR이 증가하였지만 DR에서는 SNR과 CNR이 감소하였다. 인체모형팬텀 실험에서는 CR의 경우에 저에너지 저선량과 고에너지 고선량에서만 SNR과 CNR이 증가하였지만 다른 모든 조건에서는 SNR과 CNR이 감소하였다. 결론적으로 환자에게 온화한 느낌과 안전감을 제공하고 심적인 불안감을 해소하여 검사에 도움을 줄 수 있지만 임상적용에 있어서는 탄소발열체를 포함한 바닥필름과 보호필름의 두께와 재질을 고려하지 않으면 화질에 영향이 주기 때문에 향후 지속적인 연구가 필요하다고 사료된다.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.7-13
• /
• 2010

Linear motors are efficient mechanism that offers high speed and positioning accuracy. By eliminating mechanical transmission mechanisms, much higher speeds and greater acceleration can be achieved without backlash or excessive friction. However, an important disadvantage of linear motor system is its high power loss and heating up of motor and neighboring machine components on operation. Therefore, it is necessary to design moving table with high stiffness, high efficiency and light weight construction. This paper presents the development of moving table using composite material. In order to develop light weight construction of moving table, finite element analysis is performed to find best moving table construction and composite stacking sequence. NASTRAN and MINITAB were used as the optimizer. A prototype for the moving table using composite material was created.

• Journal of the Korean Wood Science and Technology
• /
• 제25권2호
• /
• pp.52-60
• /
• 1997

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split- resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent, wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heat ed f or 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• 제11권2호
• /
• pp.52-60
• /
• 1983

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split-resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent-wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heated for 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• 제23권3호
• /
• pp.73-82
• /
• 1995

Black locust trees(Robinia pseudo-acacia L.) are growing widely in Korea and have been used to get honey and animal feed, but they have seldom been used as manufacturing materials. This study was carried out to evaluate the possibility of using black locust as bent-wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of 15${\times}$15${\times}$350mm were all air-dried. For softening, specimens were steamed at 100$^{\circ}C$ for 7 min, or microwave heated for 35 seconds. It is known that microwave heating softens wood much faster than steaming. The bending processing conditions are showed in Table 7. The minimum solid-bending radii of black locust were 40mm for steaming and 150mm for micro-wave heating, respectively. In conclusion the steamed black locust, showed very good solid bending properties, but the bending properties of micro-wave heated black locust were not sufficient for bent-wood furniture.

• 한국산업융합학회 논문집
• /
• 제21권5호
• /
• pp.257-263
• /
• 2018

It is a small injection molding machine for table top considering the material heating mechanism and the design and structure stability by securing the mechanism that compresses the inside of the material heating tube by using the electric actuator and by providing space between the body and the material heating tube to reduce heat loss Develop body. An electric actuator suitable for applying pressure to the inside of a material heating tube is a mechanical system composed of a rigid structure. Since a large force is repeatedly applied to the electric actuator and the push rod, the interaction between the moving parts and the dynamic Maximum stress through analysis and prediction of fatigue life of critical parts The pushrod reflects the structural analysis results of the electric actuator and the push rod, and pushes the inside of the material heating tube by the push rod to inject the molten material from the nozzle into the mold. The pushrod operates by the operation of the electric actuator. The material heated by the coil heater is ejected through the nozzle by the pressure of the material heating tube, and the material heating tube and the nozzle are also lowered at the same time as the push rod is lowered, so that the material is closely adhered to the mold. We want to study the completion of the injection.