• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.2
• /
• pp.117-131
• /
• 2006

A coupled T-H-M(Thermo-Hydro-Mechanical) analysis was carried out for KENTEX (KAERI Engineering-scale T-H-M Experiment for Engineered Barrier System), which is a facility for validating the coupled T-H-M behavior in the engineered barrier system of the Korean reference HLW(high-level waste) disposal system. The changes of temperature, water saturation, and stress were estimated based on the coupled T-H-M analysis, and the influence of the types of mechanical constitutive material laws was investigated by using elastic model, poroelastic model, and poroelastic-plastic model. The analysis was done using ABAQUS, which is a commercial finite element code for general purposes. From the analysis, it was observed that the temperature in the bentonite increased sharply for a couple of days after heating the heater and then slowly increased to a constant value. The temperatures at all locations were nearly at a steady state after about 37.5 days. In the steady state, the temperature was maintained at $90^{\circ}C$ at the interface between the heater and the bentonite and at about $70^{\circ}C$ at the interface between the bentonite and the confining cylinder. The variation of the water saturation with time in bentonite was almost same independent of the material laws used in the coupled T-H-M processes. By comparing the saturation change of T-H-M and that of H-M(Hydro-Mechanical) processes using elastic and poroelastic material mod31 respectively, it was found that the degree of saturation near the heater from T-H-M calculation was higher than that from the coupled H-M calculation mainly because of the thermal flux, which seemed to speed up the saturation. The stresses in three cases with different material laws were increased with time. By comparing the stress change in H-M calculation using poroelasetic and poroelasetic-plastic model, it was possible to conclude that the influence of saturation on the stress change is higher than the influence of temperature. It is, therefore, recommended to use a material law, which can model the elastic-plastic behavior of buffer, since the coupled T-H-M processes in buffer is affected by the variation of void ratio, thermal expansion, as well as swelling pressure.

• The Journal of Natural Sciences
• /
• v.5 no.2
• /
• pp.49-62
• /
• 1992

This study was carried out to investigate the emergence, growth and yield components in rice inassoccation with Several cultivation methods direct sowing flooded paddy field(DSF), direct sowing by airplane(DSA), direct sowing in dry paddy field(DSD), 8days seedling planting(8DS), and 35days seedlingplanting(35DS). Also this study was attempeted to know the effects of calcium peroxide on germinationand early growth of rice under different soil conditions, seeding depth, application of organic matter,indirect sowing flooded paddy field.1. Rate of emergence was 73% in DSF, 70% in DSA, 62% in DSD, respectively, under the different cultivation method of rice in reclaimed paddy field.2. Degree of lodging in relation to cultivation was 5 at both DSF and DSA, 3 at DSD, 2 at both 8DS and 35DS respectively.3. Maximum tiller number was 568 per m2 at DSF and 527 at DSA. Heating was delayed for 4 days at DSF, 8 days at DSD and 2 days at 8DS as comparison with that at 35DS.4. Yield was higher 1% to 3% at DSF than that at DSA and DSD while decreased by 12% as compared with that of seedling planting.5. Total dry weight of seedling was decreased by 57% at 8DS, 60% at DSF 63% at DSD, respectively, under 0.3% of salinity. Ratio of decreasing in dry weight was higher with high salinity.6. The amount of O2 released was recorded highest to 2 to 3days after irrigatition, thereafter remaining constant to 10 days after irrigatition.7. The optimum coating amount of calcium peroxide for germination was a half of rice seed weight with 1 cm sowing depth and one-fold with 2-cm sowing depth when rice straw was not applied. With rice straw applied, on the other hand, the amount of peroxide was one-fold with 1-cm sowing depth. It was found that, under the condition of applied 600kg/10a, of 2-cm soil depth with rice straw calcium peroxide coating had no effect on emergence of rice seedling.8. In reclaimed paddy field, lodging degree was 7 with direct sowing by machine and 9 with direct sowing by hand.9. Yield was increased by 5% by applying rice straw with direct sowing by machine.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.24 no.2
• /
• pp.123-129
• /
• 1991

The skipjack and Alaska pollack meat were packed in square No. 3B can, and thermally processed at $121.1^{\cir}C$ so far as to reach Fo values of 5, 10 and 20, respectively. Also the another samples which were heated at $98^{\cir}C$ for 30 minutes were prepared. We have examined the changes of nitrogenous extractives and texture by thermal processing at high temperature in both fish meats. Moisture contents of both fish meats decreased slightly with the increasing of Fo values. When the samples were heated at $98^{\cir}C$ and $121.1^{\cir}C$, pH and VBN contents increased markedly in both fish meats; increasing ratio of pH and VBN contents in skipjack meat was larger than those of Alaska pollack meat. Histamine were detected in concentration of 6.1mg/100g, 0.1mg/100g in raw skipjack and Alaska pollack meat, 8.2mg/100g, 0.1mg/100g in Fo 20 samples of these fish meats, respectively. The contents of total free amino acids in skipjack and Alaska polack meat were 984.8mg/100g, 282.3mg/100g, and these total contents decreased slightly with increasing of Fo values. Little changes were observed in free amino acid composition, but only His, Tau, Ala in skipjack meat and Tau in Alaska pollack meat decreased significantly by heat treatment. Also the degredation of IMP were Proceeded during Preparation and heat treatment of samples, and TMAO changed into TMA almost equivalently. In changes of textures, as compared with heating of 98t for 30 minutes; Fo 5 heat treatment became more softened these fish meats.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.2
• /
• pp.243-248
• /
• 1998

Ark shell was known as shellfish that had hemoglobin as blood pigment and the action of mecidine, was consumed the great part of it as raw material, though it was produced about 13,000 M/T per year. Ark shell was processed the infinitesimal quantity as conned product, bout canned ark shell had problem that occurrenced discoloration after heat treatment during processing and storage. This discoloration mechanism during processing and storage was not cleared. This study was carried out to understand characteristics of the hemoglobin as blood pigment and carotenoid as meat pigment in ark shell and management of proper processing conditions for prevention of oxidation and discoloration by thermal treatment. When treated by digestion of 0.1% BHA, 0.1% Tenox-II, 0.5% Na2EDTA, 0.05% NDGA and 3% salt soln., 0.1% BHA solution was most suitable for stability of carotenoid that the retention ratio of carotenoids were 63.1% after heating to 116$^{\circ}C$ for 120 minutes. In preparation of canned ark shell and storage at 37$\pm$1$^{\circ}C$ for 60 days, the chemical composition, pH and salinity ere stable. And contents of total carotenoid were decreased slightly from 0.83mg% to 0.727mg%. The viable cell count were 6.92$\times$103 cfu/ml at raw ark shell, after processed and storage were not detected. The predominant amino acids in the raw ark shell were glutamic acid(19.7%), arginine(16.0%), glycine(12.6%), alanine(12.2%) and aspartic acid(7.6%). When 60 days stored, the contents of amino acid were stable. And the predominant nuclotide and their related compounds in the raw ark shell were hypoxanthine(2.14$\mu$mol/g), IMP(1.94$\mu$mol/g) and ATP(0.87$\mu$mol/g), and storage at 37$\pm$1$^{\circ}C$ for 60 days, the quantity order were same as raw material.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.579-588
• /
• 2016

This study analyzed nonmetallic inclusions in iron swords with a ring pommel excavated in the Ipbuk-dong, Suwon. Scanning electron microscopy with energy dispersive spectroscopy(SEM-EDS) was used to estimate the iron-making temperature, and we compared the oxide with $SiO_2$ to investigate the heat-treatment technology in the production of iron swords with a ring pommel by investigating the artificial insertion of a slag former and the metallurgical structure. From the wustite observed in most of the specimens, it is judged that these swords were produced by heating and forging iron smelted at a low temperature using the solid reduction method. In addition, judging from the partial presence of $P_2O_5$, it is assumed that they were smelted directly with natural ore, not calcined. From the ratios of $CaO/SiO_2$ and $TiO_2/SiO_2$, it is judged that the raw material for iron-making was iron ore and that a calcareous slag former was not artificially inserted. The structure of the blade part on the front end was pure iron. From the high carbon content of the blade part on the ring pommel and the formation of a martensitic structure and pearlite colony, it is judged that they were tempered after carburizing and that the back, handle part, and ring pommel were unintentionally carburized. Judging from the structure of these specimens, it was noted that they were produced by applying artificial partial heat-treatment technology. This study attempted to present a more scientific analysis by using the method of interpretation through component analysis of nonmetallic inclusions appearing in one relic by the ratio of the oxide divided by $SiO_2$. It is judged that reinterpreting the arguments by the results of the existing analysis and research in this way can obtain different interpretations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• Journal of Bio-Environment Control
• /
• v.32 no.4
• /
• pp.278-284
• /
• 2023

Recently, a closed-type plant factory has been receiving attention as a advanced agricultural method. It has diverse advantages such as climate-independence, high productivity and stable year-round production. However, high energy cost caused by environmental control system is considered as a challenges of a closed-type plant factory. In order to reduce the energy cost, investigation about energy load which is directly connected to energy consumption needs to be conducted. In this study, energy load changes of a plant factory have been analytically analyzed according to the environmental changes. The target plant factory was a lettuce growing container farm. Firstly, the impact of photoperiod, set temperature and relative humidity change were examined. Under the climate condition of Daejeon in South Korea, increase of photoperiod and set temperature rose a yearly energy demand of a container farm. However, increase of set relative humidity decreased a yearly energy demand. Secondly, the climate environment effect was compared by investigating the energy demand under 9 different climate conditions. As a result, the difference between maximum and minimum value of the yearly energy demand showed 21.7%. Lastly, sensitivity analysis of each parameter (photoperiod, set temperature and relative humidity) has been suggested under 3 different climate conditions. The ratio of heating and cooling demand was varied depending on the climate, so the effect of each parameter became different.