• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2002년도 춘계 학술발표회 논문집
• /
• pp.227-234
• /
• 2002

With the increasing environmental consideration and stricter regulations, gasification of waste is considered to be more attractive technology than conventional incineration for energy recovery as well as material recycling. The experiment for combustible waste mixed with plastic and cellulosic materials was performed in the fixed bed gasifier to investigate the gasification behavior with the operating conditions. Waste pelletized with a diameter of 2~3cm and 5cm of length was gasified at the temperature range of 1100~145$0^{\circ}C$. It was shown that the composition of H$_2$ was in the range of 30~40% and CO 15~30% depending upon oxygen/waste ratio. Casification of waste due to thermoplastic property from mixed plastic melting and thermal cracking shows a prominent difference from that of coal or coke. It was desirable to maintain the top temperature up to foot to ensure the mass transfer and uniform reaction through the packed bed. As the bed height was increased, the formation of H$_2$ and CO was increased whilst $CO_2$ decreased by the char-$CO_2$ reaction and plastic cracking. From the experimental results, the cold gas efficiency was around 61% and heating values of product gases were in the range of 2800~3200㎉/Nm3.

• 한국산업융합학회 논문집
• /
• 제9권1호
• /
• pp.51-59
• /
• 2006

The study is diagnosis about fatigue failure phenomenon of heating coil spring (sup9) and heat treatment method that is used to crusher. Because more than 80~90% of damage announcement of breakdown of machine and construction is been caused in fatigue present state, fatigue failure became important leading person at design. Calculated design load is imposed repeatedly that fatigue breakdown is safe. Is phenomenon that change load is imposed in the construction continuously. Used coil spring applies heat 30minute by Quenching temperature $860^{\circ}C$ if see manufacturing process and temperature of gasoline of $50^{\circ}C$ keep after quench that know tempering a $460^{\circ}C$ 90minute a product be. If doto apply heat $950^{\circ}C$ material at rolling process historically before quenching, austenite formation clay pipe being done AGS(Austenite Grain Size) by 2.5~4 become. Apply heat quenching 30minute by $820^{\circ}C$ by improvement method and after quench that keep $50^{\circ}C$ in oil tempering if do $450^{\circ}C$, 90minute spring ideal formation sorbite formation of the river form and condition that satisfy most more than AGS 7 appeared. Also, we can secure authoritativeness through MT since shot peening processing.

• 한국항공우주학회지
• /
• 제31권4호
• /
• pp.44-52
• /
• 2003

형상기억합금은 스마트 구조물에서 작동기로 널리 쓰인다. 형상기억합금은 초기변위를 부고 열을 가하게 되면 단위 부피당 큰 회복력과 변위를 발생한다. 형상기억합금의 이론 특성은 인공근육, 작동기, 소음 및 진동감쇠, 형상의 변형 제어 등에 응용될 수 있다. 본 논문에서는 형상기억합금의 3차원 비선형 구성방정식을 이용하여 재료의 거동특성을 해석하고, 형상기억합금이 부착된 스마트구조로 응용될 수 있는 공기 흡입 덕트, 항공기 및 잠수함 동체 등의 구조를 압력이 존재하는 원형 및 복원을 해석하였다. 수치해석결과, 형상기억합금 엑츄에이터가 내압 하에서 작동하자 단면은 변형전의 모습(낮은 응력상태)으로 회복되었다.

• 한국축산시설환경학회지
• /
• 제11권2호
• /
• pp.97-102
• /
• 2005

Anaerobic decomposition is one of the most common processes in nature and has been extensively used in waste and wastewater treatment for several centuries. New applications and system modifications continue to be adapted making the process either more effective, less expensive, or suited to the particular waste in question and the operation to which it is to be applied. Animal manure is a highly biodegradable organic material and will naturally undergo anaerobic fermentation, resulting in release of noxious odors, such as in manure storage pits. Depending on the presence or absence of oxygen in the manure, biological treatment process may be either aerobic or anaerobic. Under anaerobic conditions, bacteria carry on fermentative metabolisms to break down the complex organic substances into simpler organic acids and then convert them to ultimately formed methane and carbon dioxide. Anaerobic biological systems for animal manure treatment include anaerobic lagoons and anaerobic digesters. Methane and carbon dioxide are the principal end products of controlled anaerobic digestion. These two gases are collectively called biogas. The biogas contains $60\~70\%$ methane and can be used directly as a fuel for heating or electrical power generation. Trace amounts of ammonia and hydrogen sulfide ($100\~300\;ppm$) are always present in the biogas stream. Anaerobic lagoons have found widespread application in the treatment of animal manure because of their low initial costs, ease of operation and convenience of loading by gravity flow from the animal buildings. The main disadvantage is the release of odors from the open surfaces of the lagoons, especially during the spring warm-up or if the lagoons are overloaded. However, if the lagoons are covered and gases are collected, the odor problems can be solved and the methane collected can be used as a fuel. Anaerobic digesters are air-tight, enclosed vessels and are used to digest manure in a well-controlled environment, thus resulting in higher digestion rates and smaller space requirements than anaerobic lagoons. Anaerobic digesters are usually heated and mixed to maximize treatment efficiency and biogas production. The objective of this work was to review a current anaerobic biological treatment of animal manure for effective new technologies in the future.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.114-125
• /
• 2002

As semi-solid forging (SSF) is compared with conventional easting such as gravity die-easting and squeeze casting, the product without inner defects can be obtained from semi-solid forming and globular microstructure as well. Generally speaking. SSF consists of reheating, forging, ejecting precesses. In the reheating process, the materials are heated up to the temperature between the solidus and liquidus line at which the materials exists in the form of liquid-solid mixture. The process variables such as reheating time, reheating temperature, reheating holding time, and induction heating power have much effect on the quality of the reheated billets. It is difficult to consider all the variables at the same time when predicting the quality. In this paper, Taguchi method, regression analysis and neural network were applied to analyze the relationship between processing conditions and solid fraction. A356 alloy was used for the present study, and the learning data were extracted by the reheating experiments. Results by neural network were on good agreement with those by experiment. Polynominal regression analysis was formulated by using the test data from neural network. Optimum processing condition was calculated to minimize the grain size, solid fraction standard deviation, otherwise, to maximize the specimen temperature average. In this time, discussion is liven about reheating process of row material and results are presented with regard to accurate process variables for proper solid fraction, specimen temperature and grain size.

• 펄프종이기술
• /
• 제37권3호
• /
• pp.23-32
• /
• 2005

A change of z-directional structural and surface properties by calendering has a great influence on liquid penetration into a sheet. It could be also important for multi-ply sheet because it contacts liquid dunhg coating or converting process. Therefore, this study was aimed to evaluate of a change of z-directional structure in multi-ply sheet by calendering. To do this, multi-ply sheets were prepared with various raw materials and calendered at the different pressure and temperature conditions. In multi-ply sheet which consisted of one kind of pulp fiber, thickness reductions were higher in top and bottom plies than in middle plies. And in the case of soft nip calender treatment with high temperature, top layer which was in contact with heating roll showed the highest reduction of thickness. Hard nip calender treatment showed U-shaped density profile in z-direction, but compression profile by SNC treatment was dependent on calendering condition. To examine z-directional structure of multi-ply sheet which was composed of different raw material for each layer, CLSM (Confocal Laser Scanning Microscopy) analyses were carried out on cross direction of sheet. It turned out to be a useful tool for investigating z-directional analysis. As a result, variation of thickness reduction in z-direction is dependent on ply structure, compressibility of pulp fiber, and calendering condition.

• 대한가정학회지
• /
• 제47권2호
• /
• pp.39-53
• /
• 2009

The purpose of this study was to analyze the state of Vietnamese housing in Korea. Using ethnographic methodologies, it was examined that 22 Vietnamese households in Korea in relation to their usage of housing space. The following conclusion were established; 1). Most of households had kitchen+1 or 2 bedrooms and the majority households preferred separated kitchen and living room areas. 2). Most households had a washing machine in bathroom and they regarded bathtub as not very necessary. They all preferred the bathroom with enough space for using washing machine and hand washing both. 3). Their preferred seating style was using chairs on sleeping as like in Vietnam but they preferred eating without chairs and treated large family and guest without chairs specially. 4). All of them were took their shoes off usually and preferred designated shoes space at the entrance to the house which was not used in Vietnam. 5). A Floor material of all households was vinyl on living room and bedrooms and most of them who had been using tile only in Vietnam preferred vinyl here. 6). All of households had a modified Ondol and most of them who had never been used this before preferred and they regarded as a desirable heating system. 7). They considered the kitchen as the most important housing space and the direction of housing was the one to consider when they built or buy the house.

• Journal of Acupuncture Research
• /
• 제28권2호
• /
• pp.49-55
• /
• 2011

Objectives : This study was to develop programmable and rechargeable electronic moxibustion device as an interdisciplinary research focusing on traditional Korean medicine. Methods : This device deployed several advances on safety and conveniences with the advantage of programmable heat stimulation, heating material and recharging method. The gradient of heat stimulation was programmed with the reference of previous studies and own measurements. The heat curve reached its efficacious stimulus temperature after three minutes, and maintained until 13 minutes with $42^{\circ}C$. We also incorporated feedback from field hospital experiences with the help of hospital staffs. Results : This device can prevent damages from skin burn and fire accidents, and control the smoke, smell and residue of moxa itself. Conclusions : This study will contribute for the development and improvement of efficacious and safe treatment methods for the traditional Korean medicine.

• 대한의용생체공학회:의공학회지
• /
• 제30권5호
• /
• pp.418-427
• /
• 2009

As many people are westernizing their life style and food consumption habits, a number of patients who have malignant tumors which grow very rapidly and hazardously destroy the human body are increasing. Ultrasonic hyperthermia is not only one of the tumor treatment methods which employs the non-radioactive ultrasonic waves to increase the temperature at the tumor region up to $40\sim45^{\circ}C$ to destroy and suppress tumor cells but also has been proved by many studies. Due to the rapid development of High Intensity Focused Ultrasound(HIFU), the ultrasound hyperthemia extensively boosts its applications in clinical field. For those reasons, Computed simulation factor should be needed before inspection to patients. To prove efficiency of ultrasonic hyperthermia, precise acoustic field measurement considering tissue characteristics and a heating experiment with tissue mimicking material phantom were conducted for effectiveness of simulation program. Finally, in this study, the computer simulation program verified the anticipated temperature effects induced by ultrasound hyperthermia. In the near future, it is hoped that this simulation program could be utilized to improve the efficiency of ultrasound hyperthermia.

• 한국결정성장학회지
• /
• 제18권4호
• /
• pp.174-178
• /
• 2008

본 연구에서는 균일침전법으로 합성된 $CaCO_3$를 하소한 후 수화시키는 방법을 이용하여 소석회를 제조하였다. 소석회를 제조하기 위하여, 염화칼슘$(CaCl_2)$과 우레아(Urea)가 출발 물질로 사용되었으며 염화칼슘 수용액과 우레아 수용액을 혼합하여 가열하는 동안 반응용기 내에서 탄산칼슘이 합성되었다. 침전물들을 여과하고 증류수와 에탄올로 수 차례 세척하였으며 건조시켰다. 소석회는 하소된 탄산칼슘의 수화과정을 통하여 합성되었다. 최적의 합성조건을 선정하는데 있어 실험의 잡음인자를 최소화하고 결과를 통계적으로 추론할 수 있는 실험계획법(다구치 실험계획법)을 이용하였다. 제조된 탄산칼슘을 $1000^{\circ}C$에서 30분 동안 하소시킨 후 에탄올 및 옥살산이 첨가된 증류수로 수화시킴으로써 결정입자 크기가 약 50 nm인 소석회를 제조할 수 있었다.