• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.338-341
• /
• 2008

Galvannealed Sheet Steel, which is being widely used in the automotive industry, is made by reheat after dip zinc galvanizing process. By this, A Fe-Zn alloy is created which enhance anticorrosive property and weldability. This paper describes basic design for 2000kW induction heating inverter system for galvannealling process and test result of 250kW inverter module which is used in parallel to form 2000kW inverter system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.160-161
• /
• 2006

To Improve the mean-life and the reliability of power cable, we have investigated thermal conductivity of XLPE insulator and semiconducting materials in l54[kV] underground power transmission cable. Specimens were made of sheet form with the nine of specimens for measurement. Thermal conductivity were measured by Nano Flash Diffusivity thermal conductivity measurement temperature ranges of XLPE insulator were from 20[$^{\circ}C$] to 90[$^{\circ}C$], and the heating rate was 1[$^{\circ}C$/mm]. In case of semiconducting materials. the measurement temperature ranges of thermal conductivity were from 20[$^{\circ}C$] to 60[$^{\circ}C$], and the heating rate was 1[$^{\circ}C$/min].

• Journal of the Korean institute of surface engineering
• /
• v.34 no.3
• /
• pp.240-246
• /
• 2001

The possibility of using a glass block with the composition of sodium borosilicate as starting materials for GRIN glass was examined from the view points of the phase separation of the matrix glass, the effects of leaching and the heating conditions for a porous structure, and the change in the refractive index. Glass specimens with similar compositions were prepared in the form of porous glass using a phase-separation technique. An examination of the heating and leaching conditions and the microstructure dependence of these conditions was made.; Specimens with porous structure were obtained when the heat treatment and leaching conditions were fixed at $540^{\circ}C$ for 30hrs and in a 0.3N$ H_2$$SO_4$ solution at $100^{\circ}C$, respectively. The resultant specimens had some important features on the GRIN glass.; the depth of the gradient and the change in refractive index (Δn) were 4mm and 0.015~0.02, respectively.

• Journal of Dairy Science and Biotechnology
• /
• v.19 no.1
• /
• pp.13-21
• /
• 2001

Milk can be regarded as a complete food, containing protein, fat, lactose, vitamins and minerals. Milk is heated for a variety of reasons. The main reasons are: to remove pathogenic organisms; to increase shelf-life. But, when milk is heated, many changes take place: denaturation of whey proteins and interaction with casein, Maillard browning, losses of vitamin and minerals. The addition of a additive and milk powder to flavor and taste may cause undesirable change of quality during heating milk. The reconstituted milk is the milk product resulting from the addition of water to the dried or condensed form in the amount necessary to re-establish the specified water solids ratio. Therefore, according to the increasement of consumption of processed milk, the necessity for study about the quality of processed milk mixed with reconstituted milk arose.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.44-47
• /
• 2004

Although bulk metallic glasses have many outstanding aspects in their chemical, mechanical or functional properties, some critical problems still hinder their wide application. The most important one is the brittle nature of them, which is the serious problem to structural application. So, to use viscous flow is now the only competent way to form bulk metallic glass. In this study, we investigated the basic nature of viscous flow of Zr-base bulk metallic glass, vitrelloy 1, in terms of process variables. The results were used to design the thermo-mechanical process composed of heating, holding, pressing, and cooling, which have unique influence on the glass transition and crystallization behavior. We adopted small load scale and dies with nano/micro patterns on them. The results were evaluated using several analytical methods.

• Journal of Fisheries and Marine Sciences Education
• /
• v.20 no.3
• /
• pp.508-519
• /
• 2008

Hot air drying is a method that let moistures evaporate by heat exchange between heating air and dry target. This way is dominating more than about 70% of dryers that the use extent is wide fairly, and is established in domestic than dryer that use conduction or radiation etc. Most of research about drying had been emphasized in size of device through analysis for these dry phenomenon plain, heating topology, and aspect of form and so on by dry target's special quality, and research about device development or waste heat withdrawal technology in energy utilization efficiency side is slight real condition. Therefore, in this study, Investigated numerically about thermal efficiency elevation that is leaned against as that change the temperature of inlet and outlet in heat exchanger of the hot air drying tower.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.3
• /
• pp.538-545
• /
• 1995

The heat transfer model of ondol heating system is derived in the linear form. The step responses of On-Off controller, PID controller and Position type fuzzy controllers are compared in the sense of several aspects : variation of temperature feedback variable, variation of supplied heat quantity by the boiler, variation of flow rate, variation of thickness of the base, variation of the outdoor temperature.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2254-2255
• /
• 2008

Thermoforming is one of the most versatile and economical process to produce polymer products. The drawback of thermoforming is difficult to control thickness of final products. Temperature distribution affects the thickness distribution of final products, but temperature difference between surface and center of sheet is difficult to decrease because of low thermal conductivity of ABS material. In order to decrease temperature difference between surface and center, heating profile must be expressed as exponential function form. In this study, Finite Difference Method was used to find out the coefficients of optimal heating profiles. Through investigation, the optimal results using Finite Difference Method show that temperature difference between surface and center of sheet can be remarkably minimized with satisfying Temperature of Forming Window.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.1
• /
• pp.54-59
• /
• 2006

The smart space is composed of the wire and/or wireless network, multi-sensor-based environment, and many various controllers. For the smart space, this paper presents a new design method of multirate digital decentralized controller using the intelligent digital redesign technique. In specific, the proposed method is based on the delta-operator and the multirate sampling and takes the form of the LMIs. To shows the feasibility of the suggested method, the computer simulations for Heating, ventilating, and ai. conditioning (HVAC) system are provided.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.1
• /
• pp.156-165
• /
• 1994

Unsteady heat conduction in stacked disks in a furnace has been numerically solved The effects of relevant parameters such as disk spacing, aspect ratio, environmental temperature, Biot nember, etc. have been investigated. The highest temperature appears at the disk edge and the lowest at the center. Penetration of heat form the surface to the center requires some time. Heating should be slow for uniform temperature rise. Geometric parameters complicates the radiative and conductive heat transfer. Though the resulting dependence of temperature nonuniformity on various parameters is complicated, high uniformity of temperature is in general available by low Biot number and/or low environmental temperature.