• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1323-1326
• /
• 2007

A new driving method employing 2-dimensional spatial averaging is proposed. This method successfully eliminates the vertical line artifact caused by luminance difference from unbalanced charging voltage between polarities. This spatial averaging method can secure charging time, minimize driver heating, and achieve higher display quality.

• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.37-44
• /
• 1998

The adequate design of a passenger car's braking system, which is directly related to the safety of a car, is very important since the safety is an essential design parameter of a car to keep men and car from the damage. The general method to verify the performance and safety of a braking system is still based on the trial-error experiments. However, the design based on experiments costs high and is time-consuming method. So it is desirable to use the numerical analysis method for the reduction of cost and time in the design of a braking system. In this paper, the thermal characteristic of a ventilated disc brake has been analyzed as a function of the car speed and a deceleration during quick braking.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.522-526
• /
• 1989

Recently developments of high-speed Semi-conductor Switches as Power MOSFETS, Power IGBT, power SIT have enwidened the performance of classical inverter configuration, and also allowed the practical applications of new inverter configuration, with improved performance and wider operating zones. Static power converters are now used in a great variety of applications including induction heating, high-frequency generation, DC/DC power converter, etc.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.143-146
• /
• 2004

Pultrusion process of phenolic foam composite is investigated. Phenolic foam composites provide heat and flame resistance with less weight. When made into foam, a variety of properties can be obtained with different bubble size and number density. In this study, effect of process variables on the foaming characteristics of phenolic resin composites during pultrusion process has been studied experimentally. The process variables considered are the heating temperature and the pulling speed as well as the mass fraction of blowing agent. Experiments were performed using a laboratory scale pultrusion apparatus. Optimal process condition was found by observing the micro-morphology.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.54-61
• /
• 2006

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the ANDRICH type dryer through the changing rotational speed from 3rpm to 10rpm. A PIV can be applied to research a inner flow of ANDRICH type dryer.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1326-1331
• /
• 2009

Drying process in the cylindrical thin film layer of sludge with the thickness less than a few millimeters has been investigated. Thin film drying is specially designed and used to dry the viscous materials like sewage sludge. The thin film layer of sludge is dried on the metallic cylindrical surface through which thermal energy is supplied to the layer during drying. The wall temperature is assumed to be constant during drying in the present study for the simplification. In order to solve the equations, the mass transfer rate on the drying surface should be determined. The mass flux of evaporated water vapor on the surface is estimated with the formulation given in the literature. The effect of some physical parameters on drying has been examined to figure out the drying characteristics of the sludge layer.

• New & Renewable Energy
• /
• v.9 no.1
• /
• pp.17-24
• /
• 2013

Eddy Current is one of ways to make heat using rotational energy of wind turbine rotor. Four difference arrays of permanent magnets around rotor surface are used to generate heat using eddy current in this study. For the evaluation of heating performance, new test rig is prepared to measure water flow and temperatures in the inlet and outlet of the eddy current heat generator. In the test, torque and rotational speed are also measured in the motor driven system, and evaluated if the torque is matched with it of wind turbine rotor or not. It will be shown that the eddy current heat generator can be applied to real urban wind energy systems in this study.

• Journal of Welding and Joining
• /
• v.21 no.3
• /
• pp.35-39
• /
• 2003

Laser welding has good characteristics such as high density energy, high speed and short heating time, as compared with conventional arc welding. The joint of laser welding also has good mechanical characteristics in general. However, relevant research is not sufficient to understand laser welding in the view point of mechanics until a recent date. In this paper, numerical simulation has been conducted to analyze distribution of welding residual stresses. Welding residual stresses of specimen have been measured by using sectioning method to compare the results between simulation and experiment.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.211-215
• /
• 2000

Bi-2212 HTS tube was fabricated by CFP(Centrifugal Forming Process). Slury was prepared in the mixing ratio of 8:2 between powder and binder and ball-milled for 24 hrs. Slurry was initially charged into the rotating mold with 300${\sim}$450 rpm and heated at the temperature ranges of 840${\sim}$860$^{\circ}$C for partial melting to finally obtain a uniformly textured tube shape. It was observed the plate-like grains with more than 20 ${\mu}$m were well oriented along the rotating axis and the measured T$_c$ was around 67K. In this paper we will discuss and analyze the tube characteristics depending on many different processing parameters such as, powder composition, binder mixing ratio between powder and binder, motor speed, heating temperature and etc.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.11a
• /
• pp.71-76
• /
• 1999

The base flow regions of a three-body sounding rocket containing multiple exhaust plumes were numerically investigated in three dimensions for a free stream Mach number of 2.7 at flight altitude 18.5 km. The flowfields were calculated using the full compressible Navier-Stokes equations with an one-equation turbulence model of Baldwin-Earth. The present calculations were executed based upon a chemically frozen, single perfect gas model assumption. Due to the symmetry of the three-body rocket of each single nozzle, only one fourth of the computational domain was considered for the analysis. The results indicate that a babe heating effect is not considerable due to the small expansion of the plumes. In the base, however, a low speed recirculating flow dominates the region.