• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.468-470
• /
• 2005

본 연구에서는 NSOM(Near-field Scanning Optical Microscope)에서 정밀도의 중요한 요소로 작용하는 100 ~ 200nm Scale의 Optical aperture를 제작하기 위해 Optical Fiber를 이용하여 $CO_2$ Laser Heating Pulling Method에 의하여 제작하고자 한다. Heating Pulling Method 에서 Fiber Tip의 정밀도 및 제작 재현성에 영향을 미치는 중요한 기존의 여러 Fiber Tip 구현방법 중 본 연구에서는 Pulse Width[$PW_{(SEC)}$] 와 Pulling Force 두 요소에 있어서 상호관계를 연구하였으며, 연구 결과 두 변수간의 최적화된 파라미터인 PW 0.07 ~ $0.10_{(SEC)}$ 와 Pulling force 0.2 ~ 0.81b의 구간에서 error율이 최소화되는 범위를 찾을 수 있었고, 그 결과 최적의 상태는 $0.08_{(SEC)}$와 0.21b에서 팁들은 첨예화 되었고 95% 이상의 재현성 및 신뢰성을 얻을 수 있었다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.4
• /
• pp.22-26
• /
• 1979

Microlenses with an extremely small radius of curvature are efficiently use d to couple LED/laser diode light into optica1 fiber. We propose a Tapered lens for the highly efficient coupling of the optical fiber communication light souses into the fiber. Ray optical analysis shows that the maximum coupling efficiency is as high as 90 %, Tapered lens with optimum parameters are fabricated by using heating and pulling technique. Experiment shows that this new technique improves the coupling efficiency by two and four times for LED and laser diode, respectively, as compared with the simple flat - end coupling.

• Journal of the Korean Home Economics Association
• /
• v.8 no.1
• /
• pp.146-158
• /
• 1970

It is a matter of amazing to realize that contamination of air by fuel gas in recent daily life at home directly effects to health of Korean housewives. A study in finding the status and the amount of co gas in the kitchen was con-ductedrelating the size of kitchen, door of exit, ventilation window, constraction of built in-brick stove (Boo Tu Mack), fuel management, in order to extend beneficial and improved management of housing. From the result of study, it was pointed out that constractional improvement of built-in-brick stove, heating floor (Ondol), timny, and ventilation window would been emergently needed. Demonstration studies were obtained in finding differences of the amount of co gas respectively in cooking time as 50-55ppm, and in not cooking time as 50-80p,p,m in the kitchen both, original and improved. Definite differences were found depend upon the condition with, without, or direction of the ventilation window. In addition to all above results, significant influence on gas pulling power of Ondol tunnel was shown. Many houses of Apartment house for have middle and low income groups been recognized so poor for health as indicated over 100ppm of co gas if window were not opened because of poor ventilation and weak gas pulling power of Ondol tunnel.

• Solar Energy
• /
• v.9 no.1
• /
• pp.14-21
• /
• 1989

Preparation of $TiO_2$ Film by the Dip-coating Method and its Application to photo-electrochemical Electrodes. $TiO_2$ film of n-type semiconductor has been of great interest as a material for solar energy conversion. For its practical application, the dip-coating method has been applied to prepare $TiO_2$ (anatase) film on the nesa glass substrate. Films up to about $1.8{\mu}m$ in thickness can be obtained by repeating the operation, dipping $\to$ pulling up $\to$ drying $\to$ heating at $500^{\circ}C$ for 10 minute. Heating temperature at $500^{\circ}C$ was adopted to convert $TiO_2$ gels into $TiO_2$ crystalline films. The $TiO_2$ films showed the maximum photocurrent ($14mA/cm^2$) at the film thickness of about $1.8{\mu}m$. It was also found that the additional heating at $500^{\circ}C$ for about 20 minutes improved remarkably the photo current of the $TiO_2$ films.

• Journal of computational fluids engineering
• /
• v.3 no.1
• /
• pp.100-107
• /
• 1998

A numerical analysis of thermal stress over temperature variations near the crystal-melt interface is carried out for a floating-zone growth of Cadmium Telluride (CdTe). Thermocapillary convection determines crystal-melt interfacial shape and signature of temperature in the crystal. Large temperature gradients near the crystal-melt interface yield excessive thermal stresses in a crystal, which affect the dislocations of the crystal. Based on the assumption that the crystal is elastic and isotropic, thermal stresses in a crystal are computed and the effects of operating conditions are investigated. The results show that the extreme thermal stresses are concentrated near the interface of a crystal and the radial and the tangential stresses are the dominant ones. Concentrated heating profile increases the stresses within the crystal, otherwise, the pulling rate decreases the stresses.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.143-146
• /
• 2004

Pultrusion process of phenolic foam composite is investigated. Phenolic foam composites provide heat and flame resistance with less weight. When made into foam, a variety of properties can be obtained with different bubble size and number density. In this study, effect of process variables on the foaming characteristics of phenolic resin composites during pultrusion process has been studied experimentally. The process variables considered are the heating temperature and the pulling speed as well as the mass fraction of blowing agent. Experiments were performed using a laboratory scale pultrusion apparatus. Optimal process condition was found by observing the micro-morphology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1058-1061
• /
• 2004

미세 소자를 관측, 가공 및 분석하기 위해 사용되는 기존 광학현미경은 빛으로 물체를 관측하므로 대물렌즈 (Object lens)에서의 회절한계 때문에 분해능의 있으므로 매우 뽀족한 탐침(Probe)을 시료의 표면에 근접시킨 후 표면을 주사하여 이미지를 얻는 방법이 개발되어 최근에는 Optical Fiber를 이용하여 fiber 끝단을 nano-scale 정도로 첨예화시키는 기술이 개발되었다. 이러한 광섬유 탐침은 구경의 직경이 작을수록 높은 분해능을 얻을 수 있으므로 광섬유 탐침의 제작 공정 확립은 매우 중요하다. 그 중에서 대표적인 방법이 $CO_2$ 레이저를 이용하여 가열한 후 인장 하는 방법 (Heating and Pulling)이 있다. 그래서 본 연구에서는 $CO_2$ 레이저를 이용하여 100nm 정도의 팁 반경을 갖는 뽀족한 탐침을 제작하고자 한다.

• Journal of the Korean housing association
• /
• v.22 no.6
• /
• pp.31-42
• /
• 2011

The purpose of the study was to investigate the characteristics of energy use behaviors and energy saving consciousness of multi-family housing residents. The energy referred to in this study includes electric energy, heating energy and water usage. This study was conducted from a survey carried out in Seoul and Gyeonggi-do. The results of the study are as follows: First, among the survey questions, the only positive energy saving behaviors shown by the occupants was turning off the lights and the television, and in the use of kitchen appliances; it could therefore be concluded that, in general, energy saving attitude and consciousness were not sufficient to reduce energy consumption. Second, the results showed high mean scores for the behaviors which were easy to control, such as turning off lights and televisions, and low mean scores for the behaviors which required extra effort to completely cut off electricity energy such as pulling out the plugs of electronic appliances. Third, it was found that the occupants generally showed the tendency to save heating energy. However, in cases where the occupants were required to continuously and directly experience indoor temperatures, they expressed passive attitudes toward saving energy. Fourth, they showed wasteful attitudes toward water usage by leaving the tap running when taking showers and washing their faces. Fifth, while they showed a strong energy saving consciousness, they also showed a passive attitude about putting this into practice; there was therefore some gap between attitude and behavior. Lastly, among the socio-demographic factors, age and family lifecycle were very important factors affecting energy use and energy saving consciousness.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.195-200
• /
• 1999

We made sharp optical fiber tips with less than 100 nm diameter by using the heating and pulling method with a good repetition and fabricated the photon scanning tunneling microscope (PSTM) using constant intensity mode. The 3-dimensional PZT (Piezoelctric transducer) scanner made of a long PZT tube is consisted of three divided parts, that is, a pair of $\pm$ x and a pair of $\pm$y scanning parts and a z scanning part for the fine approach and scanning. The scanning dimension is 1.43 $\mu\textrm{m}$$\times$1.76 $\mu\textrm{m}$. The height of a optical tip to maintain a constant height within $1/{\lambda}_0$ (${\lambda}_0$ is the incident wavelength) from surface of a specimen to a optical tip is controlled automatically by using the electric feedback circuit. The 3-dimensional shape of standing evanescent waves generated on the surface of a dove prism was measured successfully by using the constant intensity mode PSTM.

• Composites Research
• /
• v.18 no.3
• /
• pp.47-52
• /
• 2005

Pultrusion process of phenolic foam composite is investigated. Phenolic foam composites provide heat and flame resistance with less weight. When made into foam, a variety of properties can be obtained with different bubble size and number density. In this study, effect of process variables on the foaming characteristics of phenolic resin composites during pultrusion process has been studied experimentally. The process variables considered are the heating temperature and the pulling speed as well as the mass fraction of blowing agent. Experiments were performed using a laboratory scale pultrusion apparatus. Optimal process condition was found by observing the micro-morphology.