• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.3
• /
• pp.203-209
• /
• 1989

This paper is an experimental study on the pleasantly suitable cool/warm air conditioning system in order to minimize the energy consumption by attaching the electronic-controlled device to the heat pump air conditioning system.While the cool/warm air conditioning, the air temperatures in the entrance and exit of the indoor heat exchangers should be checked and when the surface of heat exchanger is reached to the dew point temperature, a speed of the compressor is to be automatically controlled by anti-dewing system in order to minimize the energy consumption.At the result of this study, the energy consuming amount is saved about 5% more than that of the conventional air conditioning system by prevent unnecessary dew forming.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.2
• /
• pp.57-63
• /
• 2010

Air curtains are widely used for gates of shopping mall, warehouse, cold stores and refrigerated display cabinets. The purpose of the air curtain is to reduce the infiltration of outdoor air and heat loss from the air conditioning space to ambient air. The discharge angle of air curtain is very important as the sealing efficiency is affected by it. This paper presents a performance of single jet air curtain in heating space when the discharge angle of nozzle changes. A numerical simulation is used to study the influence of various parameters on the efficiency of the downward-blowing air curtain device which is installed inside of the wall above the door. The performance of the air curtain is evaluated by sealing efficiency which provides the assessment of the energy savings. A condition of discharge angle that has the highest sealing efficiency is proposed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.612-616
• /
• 2000

This paper describes on the fabrication and characteristics of hot-film type micro-flowsensors integrated with Pt-RTD(resistance thermometer device) and micro-heater on the Si membrane in which MgO thin-film was used as medium layer in order to improve adhesion of Pt thin-film to SiO$_2$layer. The MgO layer improved adhesion of Pt thin-film to SiO$_2$layer without any chemical reactions to Pt thin-film under high annealing temperatures. Output voltages increased due to increase of heat-loss from sensor to external. The output voltage was 82 mV at $N_2$flow rate of 2000 sccm/min heating power of 1.2 W. The response time($\tau$:63%) was about 50 msec when input flow was stepinput

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.153-157
• /
• 2002

Electricity living body formation operation appliance is using most imports until present. And, because electricity living body formation operation appliance is too expensive, it becomes burden to buy in small scale hospital. Also, problem that economical damage by income is added follows, Therefore, this treatise developed electricity living body formation operation appliance by home production, Ultra high frequency eruption circuit used LC circuit, and output frequency is possible to 8 [MHz], and output voltage amplified maximum 800 [V]. This operation appliance could display size of fixed current. This developed product could microscopic operation fewer than 1 [mm]. This development technology is considered by do metallic surface heat treatment, melting, welding, induction heating device and that can apply to domestic animals surgical operation and so on.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.127-132
• /
• 2002

Electricity living body formation operation appliance is using most imports until present. And, because electricity living body formation operation appliance is too expensive, it becomes burden to buy in small scale hospital. Also, problem that economical damage by income is added follows. Therefore, this treatise developed electricity living body formation operation appliance by home production. Ultra high frequency eruption circuit used LC circuit. and output frequency is possible to 8 [MHz], and output voltage amplified maximum 800 [V]. This operation appliance could display size of fixed current. This developed product could microscopic operation fewer than 1 [mm]. This development technology is considered by do metallic surface heat treatment, melting, welding, induction heating device and that can apply to domestic animals surgical operation and so on.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.205-208
• /
• 2002

Thermal design is required with considering thermal stability to verify the reliability of electric power device with using IGBT. Numerical analysis is performed to analyzed the change in thermal resistance with respect to the various thermal density of heating element. Correlations between thermal resistance and heat generation density are established. With using these correlations, performance curve is composed with respect to the change in thermal resistance of cooling conditions for natural convection and forced convection. Thermal fatigue is occurred at the Inside and outside of IGBT by repeated heat load. The crack is occurred between base plate and ceramic substrate for the inside. When the crack length is 4mm, the failure is occurred. Therefore, Thermal design method considering thermal density, thermal fatigue resistance is presented on this study and it is expected to thermal design with considering life prediction.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05a
• /
• pp.128-131
• /
• 2010

Recently, environmental pollution by livestock excretion is gathering strength as livestock industry is advanced on a large scale. Bio-gas is generated more than about 70 precent if remove impurities in the course of extracting bio-gas to use livestock excretion. In this paper, we developed a device that can use it in heating after extracting bio-gas from livestock excretion collected in livestock farmhouse and can supply electricity by using generator developed in itself. Also, because this system is epoch-making no discharge system to solve smear of existing method, it is expected that we have effects to prevent environmental pollution and get alternation energy and burden on the institution to treat livestock excretion of a pig breeder is solved, if use it.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.93-94
• /
• 2014

Recently, According to increase of power demand, it was increased a demand that switching power supply have characteristic of low-loss and high-efficiency. So increase of using device, the failure rate increases and service life problem arises. Even though normal circuit protection is applied in designing stage, it is often hard to identify the cause of malfunction in certain cases such as fatigued power supply due to over-running, malfunctions of main elements or over heating. This report will cover experimental results with the prototype we made, that monitors the efficiency of switching power supply and that protects a circuit when it drops below the standard value.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.97-98
• /
• 2007

In this paper, we analyzed the reset current variation of PRAM device with top electrode using the 3-D finite element analysis tool. As thickness of phase change material thin film decreased, reset current caused by phase transition highly increased. Joule's heat which was generated at the contact surface of phase change material and bottom electrode of PRAM was given off through top electrode to which was transferred phase change material. As thermal conductivity of top electrode decreased, heating temperate was increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.568-569
• /
• 2005

한빛 자기거울 장치는 고온 플리즈마 물성을 연구하기 위한 장치로서 플러즈마 밀도 형성을 위한 slot 형 안테나 고주파 가열 시스템이 중앙 진공용기에 설치되어 있다. 본 연구에서는 이러한 고주파 전송선로, 임피던스 정합 network. 장치 임피던스를 포함하는 한빛 장치의 고주파 가열 시스템에 대하여 기존에 정립된 고주파 가열 이론[1]을 기반으로 하여 이론적인 해석만으로 구성된 회로모델을 완성하였다. 임피던스 정합 소자 값들은 임피던스 정합 조건으로 결정함으로써 다양한 장치 및 플라즈마 변수들의 함수로 표현하여 그 의존성을 조사하였다.