• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.314-314
• /
• 2010

The SiC-$ZrB_2$ composites were fabricated by combining 40vol.% of Zirconium Diboride(hereafter, $ZrB_2$) powders with Silicon Carbide(hereafter, SiC) matrix. TheSiC+40vol.%$ZrB_2$ composites were manufactured through Spark Plasma Sintering(hereafter, SPS) under argon atmosphere, uniaxial pressure of 50MPa, heating rate of $100^{\circ}C$/min, sintering temperature of $1,500^{\circ}C$ and holding time of 5min. But one on/off pulse sequence(one pulse time: 2.78ms) is 10:9(hereafter, SZ10), and the other is 48:8(hereafter, SZ48). The physical and mechanical properties of the SZ12 and SZ48 were examined. Reactions between $\beta$-SiC and $ZrB_2$ were not observed via X-Ray Diffraction(hereafter, XRD) analysis. The apparent porosity of the SZ10 and SZ48 composites were 9.7455 and 12.2766%, respectively. The SZ10 composite, 593.87MPa, had higher flexural strength than the SZ48 composite, 324.78MPa, at room temperature. The electrical properties of the SiC-$ZrB_2$ composites had Positive Temperature Coefficient Resistance(hereafter, PTCR).

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제28권4호
• /
• pp.264-273
• /
• 2002

Pulsed electromagnetic field (PEMF) was used first to induce osteogenesis in 1974. The appliance which was consisted of the Helmholtz coil configuration have used to osteogensis. The objective of this study was to determine whether PEMF, a frequency of 100 Hz and magnetic field strength of 38 gauss applied to the calvarial defect in rabbit, could affect the induction of osteogenesis and the healing of the graft bone. This field should not produce excitation of nerve or muscle and heating the tissue. To evaluate the effect of PEMF on osteogenesis, 16 rabbit under the same condition was divided into 8 experimental groups and 8 control groups. 10 mm calvarial bone defects were formed around sagittal suture. The defect of left side was left without graft while the defect of right side was grafted by bone harvested from left side. A pulsed electromagnetic field was applied for 8 hours per day. Each group was sacrificed after 1 week, 2 weeks, 4 weeks, 8 weeks. Microscopic specimens were obtained from the calvarial bone defects and surrounding tissue using Hematoxylin-Eosin staining method. The results were as follows. 1. In the group which pulsed electromagnetic field was applied, new bone formation filled up the defect was observed after 4 and 8 weeks effectively. 2. There are no difference in the healing period for the fusion between the bone and graft bone. According to the result, the PEMF with 38 Gauss, 100 Hz was very effective in the healing of bone defect and new bone formation. So The PEMF will be useful in clinical aspect for oseteogenesis.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.551-561
• /
• 1998

This paper was studied to understand the characteristics of heat transfer coefficients and surface temperature distributions around a circular combustion chamber within the heat-intercept duct of kerosene fan heater. The experiment was carried out in the heat-intercept duct of kerosene fan heater attached to the blow-down-type subsonic wind tunnel with a test section of 240 mm * 240 mm * 1200 mm. The purpose of this paper was to obtain the basic data related with normal combustion for new design from conventional kerosene fan heater, and to investigate the effect of surface temperature, local and mean heat transfer coefficients versus flow-rate of convection axial fan according to the variations of heat release conditions from kerosene fan heater during normal combustion. Consequently it was found that (i) the revolution of convection axial fan during combustion had a smaller value than that of non-combustion because of the thermal resistance due to the high temperature in the heat-intercept duct, (ii) the pressure ratio P$_{2}$/P$_{1}$ had a comparatively constant value of 0.844 according to the revolution increase of turbo fan and the heating performance of kerosene fan heater had a range of 1,494 ~ 3,852 kcal/hr, (iii) the local heat transfer coefficient around a circular combustion chamber had a comparatively larger scale in the range of 315 deg. < .theta. < 45 deg. than that in the range of 90 deg. < .theta. < 270 deg. as a result of heat transfer difference between front and back of a circular combustion chamber, and (iv) the mean heat transfer coefficient around a circular combustion chamber increased linearly like a H$_{m}$=95.196Q+104.019 in condition of high heat release according to the increase of flow-rate of axial fan.n.

• 대한기계학회논문집
• /
• 제8권2호
• /
• pp.145-153
• /
• 1984

본 연구에서는 먼저 집열기의 열성능에 관한 가장 전형적인 Hottel-Whillier- Bliss의 모델을 사용하여 모의 실험을 수행하였다. 모의 실험에 사용한 집열기의 주 요 변수는 덮개 유리의 수(N), 집열판의 방사율(.epsilon.$_{p}$), 집열판의 흡수율(.alpha.$_{p}$T),집열기 단위 면적당의 유량(G), 집열기 단열재의 $L_{b}$/ $K_{b}$, 집열기 경사각 (S),일사량(I) 등이며 이들 집열기 변수의 대표치(typical values)를 중심으로 각 변 수의 값을 변화시켜서 여기에 따른 집열기 효율 곡선의 변화를 조사하였다. 모의 실 험결과와 비교하고, 모의 실험에 사용한 수학적 모델이 집열기의 열성능을 평가하는 데에 적합한가를 확인하고, 운전중에 인위적으로 그 값을 조절할 수 있는 운전 변수중 특히 유량(G)의 변화에 따른 집열기 효율변화와 최적유량의 범위를 동시에 실험적으로 조사하기 위하여, 액체 가열식 집열기 시험장치의 회로를 보완하여 실제 태양 아래에 서 실험을 수행하였다.

• 대한기계학회논문집B
• /
• 제40권2호
• /
• pp.85-91
• /
• 2016

내연기관 자동차와 달리 전기자동차는 배터리 폐열이 부족하여 실내 난방을 위해 추가적으로 PTC 히터를 사용하고 있지만 전력소모가 큰 단점이 있다. 최근 이러한 단점을 보완할 수 있는 히트펌프 적용에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 히트펌프의 운전특성 해석을 위해 MATLAB/SIMULINK$^{(R)}$환경에서 R134a 히트펌프 모델과 캐빈 모델을 개발하였다. 모델은 여름과 겨울에서 히트펌프의 작동 특성에 따른 실내 온도변화를 나타낼 수 있으며, 모델 검증은 구성품 수준에서 응축기와 증발기의 용량 비교를 수행하였다. 또한 동일한 냉방조건에서 캐빈온도 변화 비교를 통해 캐빈 모델을 검증하였다. 해석 결과 전동압축기 소비전력은 모든 외기온도 조건에서 PTC 히터 보다 낮은 것으로 나타났다. 또한 영하조건에서 히트펌프의 난방용량이 부족한 현상에 대해 폐열회수를 적용하여 효율적인 난방 작동을 할 수 있는 조건을 분석하였다.

• 대한기계학회논문집B
• /
• 제29권5호
• /
• pp.643-652
• /
• 2005

Saturated nucleate pool boiling experiments for binary mixtures, which are consisted of refrigerant R11 and R113, were performed with constant wall temperature condition. Results for binary mixtures were also compared with pure fluids. A microscale heater array and Wheatstone bridge circuits were used to maintain the constant temperature of the heating surface and to obtain heat flow rate measurements with high temporal and spatial resolutions. Bubble growth images were captured using a high speed CCD camera synchronized with the heat flow rate measurements. The departure time for binary mixtures was longer than that for pure fluids, and binary mixtures had a higher onset of nucleate boiling (ONB) temperature than pure fluids. In the asymptotic growth region, the bubble growth rate was proportional to a value between $t^{\frac{1}{6}}$ and $t^{\frac{1}{4}}$. The bubble growth behavior was analyzed to permit comparisons with binary mixtures and pure fluids at the same scale using dimensionless parameters. There was no discernable difference in the bubble growth behavior between binary mixtures and pure fluids for a given ONB temperature. And the departure radius and time were well predicted within a ${\pm}30{\%}$ error. The minimum heat transfer coefficient of binary mixtures occurred near the maximum ${\mid}y-x{\mid}$ value, and the average required heat flux during bubble growth did not depend on the mass fraction of R11 as more volatile component in binary mixtures. Finally, the results showed that for binary mixtures, a higher ONB temperature had the greatest effect on reducing the heat transfer coefficient.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권5호
• /
• pp.717-723
• /
• 2008

The purpose of this study is to measure and analyze the indoor thermal conditions of a 8,500GT class chemical carrier which was launched on July 2007. The measurement was operated from 4th June to 4th June 2007, just before handing over to Owner. Followings are the results of this study. (1)The temperature variations of supply air were related to the outdoor temperature variations, but the humidity was stable at $65{\sim}80%$. (2)The temperature variations at the representative position of bridge, restaurant, crew's cabin showed gentle slopes. but that of conference room was very steepy. The humidities of bridge and restaurant were unstable because of outdoor-contact and cooking, respectively. (4)The temperature and humidity of ECR(Engine Control Room) which was designed to supply heating and cooling by PAC(Package Air Conditioner) were directly affected by the operating conditions of PAC. (5)The measured supply air volume from dampers of bridge, crew's cabin and conference room were satisfied with the design supply air volume. (5)For the improvement of the indoor thermal conditions, the temperature of crew's cabin and restaurant and the humidity of conference room, and the temperature and humidity of bridge should be controlled, respectively.

• 대한기계학회논문집
• /
• 제9권1호
• /
• pp.127-134
• /
• 1985

본 연구에서는 축열식 열교환기에 대한 이론해석에 2개의 변수를 적용하여 주 기가 긴 경우에 적용되는 축열체의 열전도계수가 큰 열교환기인 경우 ｆ(t)함수형, 주 기가 긴 경우 또는 짧은 경우에 적용될 수 있는 열전도계수가 작은 경우 ｆ(x,t)함수 형으로 각각 구분하여 이에대한 정확해를 구하였다. 특히 ｆ(x,t)함수형에서 2차원 Laplace 변환기법에 의한 Bessel 함수가 포함된 식을 얻고, Laplace 1차 변환온도에서 얻는 식을 급수편개하여 정리한 식으로 부터 가열주기에 있어서 주기가 짧은 축열체에 적용되어질 수도 있는 근이식인 간단한 온도분포식과 이로부터 대류열전달계수식을 얻 었다.그러나 천 양태랑, 등은 주기가 긴 경우 즉 일반 축열체에 대한 이론해석 결 과와 주기가 짧은 경우 즉 8분 주기로 실험하여 비교한 결과가 일치함을 발표하였다. 이들 연구결과를 참작할때 주기가 짧은 경우에서의 실험결과와도 비교적 일치할 것으 로 기대할 수 있어서 중도상정의 스터얼링 기관 실험에 사용된 축열기의 제원을 이용 하여 계산한 결과, 위에서 구한 온도분포식은 일치하였고 대류열전달계수식에 대하여 는 다른 실험치 보다 접근함을 확인하였다. 또한 위 기관실험치를 대류열전달계수식 에 대입하여 위 기관의 전교환 열량을 계산한 결과, 스터얼링 기관용 축열기에서 축열 비의 최적치 430%와 거의 일치하였다. 따라서 이론해석으로부터 구한 온도분포식과 대류열전달계수식의 유용성을 입증할 수 있었다.

• 대한기계학회논문집B
• /
• 제35권6호
• /
• pp.633-640
• /
• 2011

본 연구에서는 고온의 미소농도구배 조건에서의 에지화염의 안정화 및 화염 강도 변화를 실험적으로 관찰하였다. 실험 연소기는 크게 혼합기가 투입되는 슬롯과 석영 채널 및 채널 내부 가열을 위한 추가적인 예혼합 연소기로 구성되어 있다. 실험의 정확성을 위해 각 경계 조건에 대한 정량적인 검증 절차가 수행되었다. 결론적으로 연료 농도 구배의 정량적인 제어와 질소 희석비율을 조절하여 고온의 조건에서도 에지화염을 임의의 위치에 안정화 시킬 수 있었다. 에지화염 내부에 존재하는 확산화염의 화염 강도가 채널 내부의 온도증가에 따라 증가하고 질소의 희석비율 증가에 따라 감소하는 것을 보였다. 연료에 따른 화염 강도 변화를 살펴본 결과 프로판의 경우가 메탄에 비해 강도 변화율이 큰 것을 알 수 있었다.

• 한국식품영양학회지
• /
• 제29권6호
• /
• pp.985-997
• /
• 2016

The objectives of this study, which filled gaps in previous studies, were: (1) to find the optimal mixing condition of nanoemulsions containing oleoresin capsicum (OC), Tween 80, propylene glycol (PG), and sucrose monostearate (SES) by microfluidization; (2) to investigate their properties and stability depending on such factors as pH, temperature, and heating time; (3) to measure the effect of adding ascorbic acid. In order to test these objectives, the following three experiments were conducted: Firstly, in order to find the optimal mixing ratio, nanoemulsions containing OC - the mean diameter of which is smaller than 100 nm - were prepared through the process of microfluidization; and their mean particle size, zeta potential, and capsaicinoids were measured. The test results indicated that the mixing ratio at OC : Tween 80 : PG + water(1:2) = 1 : 0.2 : 5 was optimal. Secondly, the properties and stability of nanoemulsions were investigated with varying parameters. The test results illustrated that single-layer nanoemulsions and double-layer nanoemulsions coated with alginate were stable, irrespective of all the parameters other than/except for pH 3. Thirdly, the properties of nanoemulsions were then analyzed according to the addition of ascorbic acid. The results demonstrated that the properties of single-layer nanoemulsions were not affected by addition of ascorbic acid. In case of alginate double-layer nanoemulsions, the particle size was reduced, and zeta potential increased with the addition of ascorbic acid. In conclusion, the demonstrated stability of various nanoemulsions under the different conditions in the present study suggests that these findings may constitute a basis in manufacturing various food-grade products which use nanoemulsions-and indicate that food nanoemulsions, if adopted in the food industry, have the potential to satisfy both the functionality and acceptability requirements necessary to produce commercially marketable food-grade products.