• The KSFM Journal of Fluid Machinery
• /
• v.4 no.3 s.12
• /
• pp.7-13
• /
• 2001

The present study investigates convective heat/mass transfer and flow characteristics inside a cooling passage of rotating gas-turbine blades. The rotating duct has staggered ribs with $70^{\circ}$ attack angle, which are attached on leading and trailing surfaces. Naphthalene sublimation technique is employed to determine detailed local heat transfer coefficients using the heat and mass transfer analogy. Additional numerical calculations are conducted to analyze the flow patterns in the cooling passage. The present experiments employ two-surface heating conditions in the rotating duct because the exposed surfaces to hot gas stream are pressure and suction side surfaces in the middle passages of an actual gas-turbine blade. Secondary flows are generated by Coriolis and centrifugal forces in the spanwise and streamwise directions. The ribs attached on the walls disturb the mainflow resulting in recirculation and secondary flows near the ribbed wall. The local heat transfer and flow patterns in the passage are changed significantly according to rib configurations and duct rotation speeds. Therefore, the geometry and arrangement of the ribs are important for the advantageous cooling performance. The experimental results show that the ribs enhance the heat transfer more than $70\%$ from that of the smooth duct. The duct rotation generates the heat transfer discrepancy between the leading and trailing walls due to the secondary flows induced by the Coriolis force. The overal heat transfer pattern on the leading and trailing walls for the first and second passes are depended on the rotating speed, but the local heat transfer trend is affected mainly by the rib arrangements.

• Journal of the Korean housing association
• /
• v.20 no.5
• /
• pp.123-132
• /
• 2009

As society increasingly ages, maintaining an independent lifestyle at home becomes an important issue for older people. This study aims to determine old people's housing needs for maintaining an independent lifestyle despite their health status and living arrangements. A total of 438 residents voluntarily took part in a research questionnaire survey through the quota sampling method. The participants were grouped according to age (60-64, 65-69, 70-74, and over 75), gender (male and female), and house type (apartment houses and others). The results are as follows. (1) The senior residents are mostly within a non occupational, low income, and low subjective living status. (2) They are satisfied with their current residence and hope to manage the rest of their life in the same place. (3) Three out of five residents prefer the apartment housing type to other types of housing. The preferred dwelling size, number of rooms, and preference for use of an extra room all varied depending on gender and housing type as well as whether they were a couple or living alone. (4) The older residents have a higher need for a safety system than do the younger residents. Female residents pay more attention to convenience while male residents pay more attention to safety. The non-apartment residents require more modification to fundamental facilities such as a heating and ventilation system, wind protection, and additional storage than do the apartment residents. This study has thoroughly analyzed request characteristics according to basic qualities of the elderly households.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.2
• /
• pp.38-43
• /
• 2017

The role of current lead in high-temperature superconducting synchronous machine (HTSSM) is to function as a power supply by connecting the power supply unit at room temperature with the HTS field coils at cryogenic temperature. Such physical and electrical connection causes conduction and Joule-heating losses, which are major thermal losses of HTSSM rotors. To ensure definite stability and economic feasibility of HTS field coils, quickly and smoothly cooling down the current lead is a key design technology. Therefore, in this paper, we introduce a novel concept of a cooling anchor to enhance the cooling performance of a metal current lead. The technical concept of this technology is the simultaneously chilling and supporting the current lead. First, the structure of the current lead and cooling anchor were conceptually designed for field coils for a 1.5 MW-class HTSSM. Then, the effect of this installation on the thermal characteristics of HTS coils was investigated by 3D finite element analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.203-206
• /
• 2004

For the realization of PRAM, $Ge_2Sb_2Te_5$ (GST) has been employed for the phase transition between the crystal and amorphous states by electrical joule heating. Although there has been a vast amount of results concerning the GST in material aspect for the laser-induced optical storage disc applications, the process-related issues of GST for the PRAM applications have not been reported. In this work, the etching behaviors of GST were investigated when the processing conditions were varied in the high-density helicon plasma. The etching parameters of RF main power, RF bias power, and chamber pressure were fixed at 600 W, 150 W, and 5 mTorr, respectively. For the etching processes, gas mixtures of $Ar/Cl_2$, $Ar/CF_4$, and $Ar/CHF_3$ were employed, in which the etching rates and etching selectivities of GST thin film in given gas mixtures were evaluated. From obtained results, it is found that we can arbitrarily design the etching process according to given cell structures and material combinations for PRAM cell fabrications.

• Journal of Environmental Science International
• /
• v.19 no.2
• /
• pp.229-236
• /
• 2010

As air pollution has emerged as one of the most pressing urban environmental concerns, many studies have investigated the influence of air pollutants(ex: $O^3$, $NO^2$, $SO^2$, Acid rain, etc.) on roadside trees and urban grove. In Korea, population density started to increase since the industrialization. Since dense population aggravates our living conditions, it's very important for us to preserve and keep a lively and refreshing nature in order to live with green nature in harmony under the current artificial environment-dominating world. In metropolitan cities, the production of pollutants increases in proportion to population growth. The vehicle exhaust gas and air pollutants from cooling and heating systems have been the major causes of acid rain. Furthermore, tire particles which are naturally produced by tire wearing on roads and other toxic substances in exhaust gas have caused a problem in human health directly and indirectly. In fact, a lot of studies have analyzed air pollution, roadside trees and plants in Korea. However, they are mostly limited to covering the influence of air pollution on the growth of plants. No paper has clearly explained why air pollution-resistant or-vulnerable species has shown different reactions yet. Even though a lot of urban roadside trees have died or stopped to grow from time to time, this kind of problem has not been properly examined. This paper is aimed to comparatively analyze physio-ecological characteristic such as photosynthesis, chlorophyll contents, soil volume water figure out their relationship with environmental factors against the expanding roadside trees in Cheong-ju, and provide basic data for management of roadside trees and elaboration of urban environment preservation policies.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.10
• /
• pp.1549-1554
• /
• 2014

This study analyzed the production and heat stability of an emulsion made from buckwheat sprout extracts with high rutin content. To obtain high rutin contents, buckwheat was sprouted and the polyphenols and rutin were extracted from buckwheat sprouts. Concentrated extracts were made into an emulsion using a homo mixer and hydraulic homogenizer, after which heat stability was analyzed. The polyphenol contents were highest in ground sprouts grown for 8 days (10.66 mg/g), which was 10 times higher than those of buckwheat seeds. Extraction with 50% ethanol after blanching was the most effective method for obtaining extracts with higher polyphenol content and rutin content. Extracts were concentrated up to 60% soluble solid content and then emulsified using a homo mixer and hydraulic homogenizer. Heat stability of the emulsion passed through the hydraulic homogenizer was slightly higher than that made using the homo mixer. The heat stability of the emulsion was more strongly affected by heating time than temperature. In conclusion, the buckwheat concentrate emulsion passed through the hydraulic homogenizer was more heat stable than buckwheat extract alone.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.5 s.236
• /
• pp.643-652
• /
• 2005

Saturated nucleate pool boiling experiments for binary mixtures, which are consisted of refrigerant R11 and R113, were performed with constant wall temperature condition. Results for binary mixtures were also compared with pure fluids. A microscale heater array and Wheatstone bridge circuits were used to maintain the constant temperature of the heating surface and to obtain heat flow rate measurements with high temporal and spatial resolutions. Bubble growth images were captured using a high speed CCD camera synchronized with the heat flow rate measurements. The departure time for binary mixtures was longer than that for pure fluids, and binary mixtures had a higher onset of nucleate boiling (ONB) temperature than pure fluids. In the asymptotic growth region, the bubble growth rate was proportional to a value between $t^{\frac{1}{6}}$ and $t^{\frac{1}{4}}$. The bubble growth behavior was analyzed to permit comparisons with binary mixtures and pure fluids at the same scale using dimensionless parameters. There was no discernable difference in the bubble growth behavior between binary mixtures and pure fluids for a given ONB temperature. And the departure radius and time were well predicted within a ${\pm}30{\%}$ error. The minimum heat transfer coefficient of binary mixtures occurred near the maximum ${\mid}y-x{\mid}$ value, and the average required heat flux during bubble growth did not depend on the mass fraction of R11 as more volatile component in binary mixtures. Finally, the results showed that for binary mixtures, a higher ONB temperature had the greatest effect on reducing the heat transfer coefficient.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.6
• /
• pp.695-702
• /
• 2015

Recently, the improvement of mechanical and theoretical issues in geo-centrifuge test enhances the applicability and accuracy of the test. Geo-centrifuge test is appropriate to simulate the behaviors of underground structures like tunnel, since tunnel interacts with the soil and/or rock around it and the test can embody the in-situ stress conditions effectively. In this study, the seismic behaviors of twin tunnel were analyzed based on geo-centrifuge test. Flexible segment to mitigate seismic acceleration were implemented in the model with thin and thick thickness. Based on the test results, it was found that flexible segment can decrease the peak acceleration generally, however, thin flexible segment was not able to reduce peak acceleration in short-period seismic wave. Thick flexible segment was more effective in case of high bedrock acceleration condition. Additionally, 3-dimensional numerical analysis was performed to verify the characteristics of seismic behavior and the effect of flexible segment. Consequently, the numerical analysis result showed good agreement with the test result.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.2
• /
• pp.28-33
• /
• 2002

The characteristics of hull-pieces are large quantity, comparatively large piece-size, and different each shape. For the more, in the forming process(including Line-Heating Process) of curved hull pieces, shape checking processes including initial shape measurement and forming shape measurement of the each pieces are needed to achieve a given accuracy. So, the forming process of large curved hull pieces needs efficient measurement and comparison technique to check the shape and ensure the forming-accuracy In this paper, we try to construct integrated S/W, H/W system for efficient measurement and comparison of large curved hull pieces, which can apply to above forming environment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.5
• /
• pp.423-428
• /
• 2010

In this paper, we analyzed the characteristics of thermal deformation of the TPS which is a core part of engine in vehicle by measuring out-of-plane deformation using ESP!. Inspection area of a test piece was minimized to 5 cm by 5 cm by using a high resolution CCD and a zoom lens. 4-step phase shifting method was used along with phase unwrapping algorithm to get a continuous phase map, configurations and deformations were displayed as 3D images. When heating the test pieces while maintaining the temperature at about $70^{\circ}C$, the out-of-plane deformations were measured. The results showed that a test piece with longer distance traveled tends to show larger thermal deformation, we could observes a convex shaped deformation on the surface. The inner defect sample, we could monitor discontinuous pattern phase map, and a concave shaped deformation on the surface.