• 동력기계공학회지
• /
• 제10권1호
• /
• pp.71-76
• /
• 2006

This paper aims to study several type heaters which are mica heater, film heater, quartz heater and rod heater and to get an temteraturel and electrical characteristics. These four type heaters have a merit in many fields than present electric heater with nichrome wire. Carbon and mica plate heater have higher heat efficiency and less electromagnetic waves. Also it has been reported that far infrared ray emission from this heater is good for our health. Additionally heating element is thin and lighter plate. For these reasons, they will be widely used to various application such as room-heating or manufacturing goods. Experimental result confirmed that when 220V current authorized, the temperature, electric current, electric power and the resistance rise to stationary state in early stage. Moreover, the temperatures and electric characteristics show a good stability.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.292-296
• /
• 1992

There are lots of disturbance in the super heater temperature control system of power plant boiler as follows. 1.Burner light off. 2.Excess Air. 3.Burner tilt. 4.G.R fan flow. Temperature control system of super heater in the power plant has delay time about 5 min. So it is difficult to control the super heater temperature in the power plant. This paper show us the application of domestic development DCS to control the super heater temperature in seoul #5 thermal power plant unit.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2310-2312
• /
• 2004

In Korea Electric Power Corporation (or KEPCO), several Demand-Side Management (or DSM) program have been carried out to effectively meet electric power demand at least costs by modifying customers electricity use patterns. As one of them, KEPCO applies low-priced night thermal-storage power service for heat appliances to facilitate efficient use of power facilities by shifting relatively high daytime demands to night hours to build loads during the off-peak periods. In the market of heat-storage type water-heater, electric water-heater has been mostly used, but it has low energy efficiency and needs high capacity electric equipments. So in order to replace these electric water heaters, 15 HP air-source heat pump water heater is developed in Korea Electric Research Institute (or KEPRI). This paper shows that measurement system for performance testing of heat pump water heater is established and heating capacity and performance is analyzed and measured for out-door environmental change.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2019년도 전력전자학술대회
• /
• pp.265-266
• /
• 2019

This paper proposed a three-channel transformer-type power regulator to control the heater temperature by adjusting the voltage across the heater for pre-heating and the post-heating procedures of the material welding. The experimental results are carried out to verify the performance of three-channel heater temperature control for the heat treatment.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권1호
• /
• pp.43-48
• /
• 2004

This paper deals with design and fabrication of heater-triggered switching system for the high-Tc superconducting (HTS) power supply with series-connected double-pancake load. Amongst all components, heater triggering is the most important element for the performance of HTS power supply. To fabricate the optimal heater-triggered system, its characteristics have been analysed through the simulation and expriment. The thermal analysis of switching parts of the Bi-2223 solenoid according to the heater input was carried out. Based upon the analysis, 8A electromagnet current and 1.5A DC Heater current were optimally derived, and 8s and 20s for the pumping period were selected in this experiment. In the experiment. the maximum pumping current reached about 24A with Bi-2223 pancake load of 6mH.

• 한국전산유체공학회지
• /
• 제10권3호
• /
• pp.63-69
• /
• 2005

The COMS, the first meteorological geostationary satellite in Korea, is under development by KARI. The radiator size and the heater power for the thermal control of COMS are calculated using an analytic method. The total radiator area of $4.85\;m^2$ and the total heater power of 794.77 W are determined at a conceptual design of COMS. The commercial software, SINDA and TRASYS, are utilized in order to compare and verify the analytic results. The results of on-orbit numerical simulation of cold and hot cases show that the radiator size and heater power obtained from the analytic method are appropriate to maintain COMS equipments within required temperature ranges.

• 한국결정성장학회지
• /
• 제28권5호
• /
• pp.179-184
• /
• 2018

고효율 태양전지용 단결정 실리콘 웨이퍼는 쵸크랄스키 성장법으로 석영도가니 속의 실리콘 액체에서 단결정 잉곳을 성장시켜 제조된다. 석영도가니 성분 중의 하나는 산소는 실리콘 잉곳으로 유입되고, 태양전지의 전력변환 효율 저하 문제를 발생시킨다. 이러한 산소 유입을 줄이는 다양한 방법 중 하나는 히터의 모양과 구조를 변경하는 방법이 있다. 그러나 히터 구조 변경 시 단결정 실리콘 잉곳 바디 성장에 필요한 온도 분포경향에 큰 변화를 일으킨다. 따라서 본 연구에서는 쵸크랄스키 실리콘 성장에서 다양한 히터의 구조와, 히터와 석영도가니의 상대적 위치가 단결정 실리콘 잉곳 Body 성장 시의 ATC 온도와 Power 분포경향에 미치는 영향에 대하여 연구하였다. 삼중점과 히터 중심과의 위치가 가장 먼 SSH-Low가 가장 높은 ATC 온도 분포경향을 보여주었다. 또한 길이가 짧은 Short Side Heater(SSH-Up, SSH-Low)보다는 실리콘 액체를 담고 있는 석영도가니 측면의 많은 영역을 커버할 수 있는 일반 Side Heater(SH)가 가장 Power 소모 측면에서 유리하였다. 특히 본 연구 결과를 통해 고효율 태양전지용 단결정 실리콘 잉곳 성장 시 필요한 효율적인 ATC 온도를 예측할 수 있음을 확인하였다.

• 전력전자학회논문지
• /
• 제10권6호
• /
• pp.618-625
• /
• 2005

본 논문은 CRT 표시장치에서 고전류밀도를 구현하기 위한 전자총의 히터와 캐소드의 최적의 저전력설계와 실험을 수행하였다. CRT 표시장치에서 밝기, 고휘도, 고해상도와 대화면화를 위해서는 전자총 캐소드(cathode)의 고전류밀도가 필수적이다. 이를 위해서는 함침형 캐소드가 사용되며, 고전류밀도를 얻기 위해 히터의 동작온도를 높여야하는데 이에 비례하여 소비전력도 증가한다. 본 논문에서는 고전류밀도 캐소드 히터의 저전력 설계를 위하여 히터의 리드형태(Lead Type), 코팅(Coating)법, 발열부의 1차 및 2차 코일링의 피치와 권선수를 달리한 샘플을 제작, 시험하였다.

• 대한기계학회논문집B
• /
• 제34권5호
• /
• pp.465-469
• /
• 2010

발전설비 내 공기예열기는 보일러 연소가스로부터 열을 회수하여 유효열의 손실을 감소시킴으로서 보일러의 열효율을 높이기 위해 설치된다. 본 연구에서는 계획예방정비가 공기예열기의 성능에 미치는 영향을 고찰하였다. 공기예열기의 성능지표들은 공기예열기의 계획예방정비 전후의 운전 상태와 성능변화 모두를 고려하여 계산되었고, 공기예열기의 중요한 성능지표로는 가스 측 온도효율, 공기누설률, 열회수율, 열관류율과 열용량비들이다. 계획예방정비 전후의 공기예열기 성능평가로부터 공기예열기의 모든 성능 지표가 계획예방정비 후 향상되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2528-2533
• /
• 2007

Thermoforming is one of the most versatile and economical processes available for the manufacturing polymer products. The drawback of thermoforming is difficult to get uniform thickness of final products. For the distribution of thickness strongly depends on the temperature distribution of sheet, the adjustment of heater power is very important In this paper, an optimization study for getting uniform temperature distribution was carried out using dual optimization steps. At first, the steady state optimal distribution of heater power is searched by numerical optimization to get uniform temperature of sheet surface. In the second step, time-dependent optimal heater inputs have been found out to decrease the temperature difference through the direction of thickness using Rseponse Surface Method and D-optimal method. The optimization results show that the time-dependent optimal heater power distribution gives acceptable uniform sheet temperature in the field of forming temperature..