• Food Science of Animal Resources
• /
• v.29 no.2
• /
• pp.168-177
• /
• 2009

This study was conducted to investigate the dietary effects of locally grown herbs (Mentha piperascens, PM; Rubus coreanus, RC; Tagetes patula, MG) on the growth performance and meat quality of broiler chicken. A total of 600 1-d-old Ross male broiler chicks were divided into eight groups and were fed control diets (antibiotics-medicated or non-medicated commercial diets) or experimental diets (non-medicated diets containing 0.3 or 0.5% PM, 0.3 or 0.5% RC, or 0.3 or 0.5% MG) for 5wk. The body weight gains and feed conversion rates (FCRs) in all the groups that were fed diets containing PM, RC, or MG were significantly improved compared to those in the non-medicated control group (p<0.05). The relative weights of various organs, the serum cholesterol levels, and the GOT/GPT activities in all the groups were also not significantly different. The superoxide dismutase (SOD)-like activities in the groups that were fed diets containing 0.3% PM or 0.3% MG were significantly increased compared to those in the non-medicated control group (p<0.05). The number of cecal lactic-acid bacteria in the groups that were fed diets containing 0.3% PM or 0.5% RC tended to increase. The malondialdehyde contents in the leg muscles were significantly lowered by feeding with PM or MG (p<0.05). The physicochemical properties of the edible meat, including the shear force, water-holding capacity, heat loss, pH, and muscle color degrees $(CIEL^*.\;a^*.\;b^*)$, were not affected by the dietary treatments. It has been suggested that spontaneous Korean plants promote the growth of broilers and may delay lipid oxidation in edible muscles without any negative effect when added in broiler diets.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.154-162
• /
• 1998

A planar Bi-Sb multijunction thermal converter with high thermal sensitivity and small ac-dc transfer error has been fabricated by preparing the bifilar thin film Pt-heater and the hot junctions of thin film Bi-Sb thermopile on the $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-diaphragm, which functions as a thermal isolation layer, and the cold junctions on the dielectric membrane supported with the Si-substrate, which acts as a heat sink, and its ac-dc transfer characteristics were investigated with the fast reversed dc method. The respective thermal sensitivities of the converter with single bifilar heater were about 10.1 mV/mW and 14.8 mV/mW in the air and vacuum, and those of the converter with dual bifilar heater were about 5.1 mV/mW and 7.6 mV/mW, and about 5.3 mV/mW and 7.8 mV/mW in the air and vacuum for the inputs of inside and outside heaters, indicating that the thermal sensitivities in the vacuum, where there is rarely thermal loss caused by gas, are higher than those in the air. The ac-dc voltage and current transfer difference ranges of the converter with single bifilar heater were about ${\pm}1.80\;ppm$ and ${\pm}0.58\;ppm$, and those of the converter with dual bifilar heater were about ${\pm}0.63\;ppm$ and ${\pm}0.25\;ppm$, and about ${\pm}0.53\;ppm$ and ${\pm}0.27\;ppm$, respectively, for the inputs of inside and outside heaters, in the frequency range below 10 kHz and in the air.

• Journal of Food Hygiene and Safety
• /
• v.32 no.5
• /
• pp.434-442
• /
• 2017

The UV light in sunlight breaks down the chemical bonds in a polyolefin polymer through a process called photodegradation, ultimately causing cracking, chalking, colour changes, and loss of physical properties such as impact strength, tensile strength, elongation, and others. UV absorbers are used to prevent or terminate the oxidation of plastics by UV light. They are receptive to UV radiation and dissipate the energy harmlessly as heat. Benzotriazoles and benzophenones are used mainly in polyolefins such as polyethylene and polypropylene. In this study, we have developed a method for the analysis of 12 UV absorbers, which are Uvinul 3000, Cyasorb UV 24, Uvinul 3040, Tinuvin 312 and P, Seesorb 202, Chimassorb 81, Tinuvin 329, 234, 326, 328 and 327, migrated from the food packaging materials into four food simulants for aqueous, acidic, alcoholic and fatty foods. The UV absorbers in food simulants were determined by reversed-phase high performance liquid chromatograph-ultraviolet detector with 310 nm after solid-phase extraction with a hydrophilic-lipophilic balance (HLB) cartridge or dilution with isopropanol. The analytical method showed a good linearity of coefficient ($R^2{\geq}0.99$), limits of detection (0.049~0.370 mg/L), and limits of quantification (0.149~1.120 mg/L). The recoveries of UV absorbers spiked to four food simulants ranged from 70.05% to 110.13%. The developed method would be used as a reliable tool to determine concentrations of the migrated UV absorbers.

• Journal of Animal Science and Technology
• /
• v.53 no.2
• /
• pp.161-169
• /
• 2011

Methane production during anaerobic fermentation in the rumen represents an energy loss to the host animal and induces emissions of greenhouse gases in the environment. Our study focused on comparison in methane production from growing Korean native steers fed different grain sources. Six Hanwoo steers (BW = $180.6{\pm}3.1$ kg) were fed, on a DM basis (TDN 2.80 kg), 40% timothy and 60% barley concentrate (Barley) or corn concentrate (Corn), respectively, based on the Korean Feeding Standards. Each period lasted 18 days including a 14-day adaptation and a 4-day measuring times. The steers were in the head hood chamber system (one cattle per chamber) during each measuring time to measure heat and methane production per day. Different grain sources did not affect digestibilities of dry matter, crude protein, crude fiber, crude fat, NDF, ADF and nitrogen-free extract. The mean methane concentrations per day were 202.0 and 177.1 ppm for Barley and Corn, respectively. Methane emission averaged 86.8 and 77.7 g/day for Barley and Corn, respectively. Methane emission factor by maintenance energy requirement for the growing steers fed barley based concentrate was higher than the steers fed corn based concentrate (Barley vs. Corn, 31.7 kg $CH_4\;head^{-1}\;yr^{-1}$ vs. 28.4 kg $CH_4\;head^{-1}\;yr^{-1}$). Thus, methane conversion rate was 0.065 (6.5%) and 0.055 (5.5%) for Barley and Corn, respectively.

• The Journal of Korean Medicine
• /
• v.17 no.1 s.31
• /
• pp.374-406
• /
• 1996

This study has been carried out to investigate the types of differential diagnosis of amnesia. The results are as follows; 1. Amnesia has various types of differential diagnosis(辨證分型) ; deficiency of both the heart and spleen(心脾兩虛型), deficiency of the heart(心虛型), deficiency of the kidney(腎虛型), breakdown of the coordination between the heart and the kidney(心腎不交型), mental confusion due to phlegm(痰迷心竅型), accumulation of stagnant blood(蓄血型), internal injury by seven emotion (七情所傷型). 2. The type of deficiency of both the heart and spleen(心脾兩虛型) occurs when the heart and spleen is injured by overthinking(思慮過度), The symptoms are heart palpitation(心悸), continuous palpitation(??), insomnia(少寐), hypochondric discomfort(心煩), dream disturbed sleep(多夢), being easy to be scared(易驚), dizziness(眩暈), these are caused by blood deficiency of the heart(心血不足), poor appetite(飮食不振), loss of appetite(納?), short breath(氣短), sense of turgid abdormen(腹部膨滿感), loose stool(泥狀便), these are caused by deficiency of the spleen(脾虛), lassitude and weakness (身倦乏力), lassitude of the extremities (四肢無力), dim complexion (面色少華), pale lips(舌質淡), thready and feeble(脈細弱無力), these are caused by deficiency of both qi and the blood(氣血虛損). The remedy is nourishing the heart-blood(養心血) and regulating the spleen(理脾土). I can prescribe the recipes such as Guibitang(歸脾湯), Gagambosimtang(加減補心湯), Seongbitang(醒脾湯), Insin-guisadan(引神歸舍丹), Insamyangyoungtang(人蔘養榮湯), Sojungjihwan(小定志丸), Yungjigo(寧志膏), Palmijungjihwan(八味定志丸), etc., 3. The type of deficiency of the heart(心虛型) occurs when the heart-blood is injured by the mental tiredness(神勞) and so blood cannot nourish the heart. The symptoms are amnesia(健忘), short breath(氣短), heart palpitation(心悸), perspire spontaneously(自汗), facial pallidness(顔面蒼白), pale lips (舌質淡白), feeble pulse and lassitude(脈虛無力), intermittent pulse(結代脈). The remedy is nourishing the hart and blood and allaying restlessness(補心益血安神). I can prescribe the recipes such as Chenwangbosimdan(天王補心丹), Jeongji-hwan(定志丸), Gaesimhwan(開心丸), Youngjigo(寧志膏), Chilseonghwan(七聖丸), Baegseogyoungtang(白石英湯), Oseohwan(烏犀丸), Yangsinhwan(養神丸), Guisindan(歸神丹), Bogsinsan(茯神散), Jinsamyohyangsan(辰砂妙香散), Cheongeumboksinsan(千金茯神散), Samjotang(蔘棗湯), jangwonhwan(壯元丸), Sa gunjatang(四君子湯) minus rhizoma atractylodis macrocephalae(白朮) plus rhizoma acori graminei(石菖蒲), radix polygalae(遠志), cinnabaris(朱砂), etc. 4. The type of deficiency of the kidney(腎虛型) occurs when the kidney-qi and kidney-essence is deficient(腎氣腎精不足) and so it cannot nourish the brain. The symptoms arc amnesia(健忘), ache at the waist and lassitude in the lower extremities(腰산腿軟), dizziness and tinnitus(頭暈耳嗚), emmission and premature ejaculation(遺精早泄), burning sensation of the five centres(五心煩熱), flushed tongue(舌紅), rapid and small palse(脈細數). The remedy is nourishing the kidney and strengthen the essence(補腎益精). I can prescribe the recipes such as Gagamgobonhwan(加減固本丸), Jeongjihwan(定志丸), Gongseongchlmjungdan(孔聖枕中丹), Yugmigihwanghwan(六味地黃丸) plus ra-dix polygalae(遠志), fructus schizandrae(五味子), Yugmigihwanghwan(六味地黃丸) plus radix polygalae(遠志), fructus schizandrae(五味子), rhizoma acori graminei(石菖蒲), semen zizyphi spinosae(酸棗仁), Palmihwan(八味丸) plus fructus schizandrae(五味子), semen zizyphi spinosae(酸棗仁). etc., 5. The type of breakdown of the coordination between the heart and the kidney (心腎不交型) occurs when the heart-fire(心火) and kidney-fluid(腎水) are imbalanced. The symptoms are amnesia(健忘), hypochondric discomfort(心煩), insomnia(失眠), dizziness and tinnitus(頭最耳嗚), feverish sensation m the palms and soles(手足心熱), emmision(遺精), ache at the waist and lassitude in the lower extremities(腰?腿軟), flushed tongue(舌紅), rapid pulse(脈數). The remedy is coordinating each other(交通心腎). I can prescribe the recipes such as Gangsimdan(降心丹), Jujaghwan(朱雀丸), Singyotang(神交湯), Simsinyang- gyotang(心腎兩交湯), Yugmihwan(六味丸) plus fructus schizandrae(五味子), radix polygalae(遠志), Yugmihwan(六味丸) plus fructus schizandrae(五味子), radix polygalae(遠志), rhizoma acari graminei(石菖蒲), semen zizyphi spinosae(酸棗仁), etc., 6. The type of mental confusion due to phlegm(痰迷心竅型) occurs when the depressed vital energy(氣鬱) create phlegm retention(痰飮) and phlegm stagnancy(痰濁) put the heart and sprit(心神) out of order. The symptoms arc amnesia(健忘), dizziness(頭暈), chest distress(胸悶), nausea(惡心), dull(神思欠敏), dull and slow facial expression(表情遲鈍), tongue with yellow and greasy fur(舌苔黃?), sliperry pulse(脈滑). The remedy is removing heat from the heart to restore consciousness and dispersing phlegm(淸心化痰開竅) I can prescribe the recipes such as Gamibogryeongtang(加味茯?湯), Goa-rujisiltang(瓜蔞枳實湯), Jusaansinhwan(朱砂安神丸), Dodamtang(導痰湯) plus radix saussurea(木香), Yijintang(二陳湯) plus succus phyllostachyos(竹瀝), rhizoma zingiberis(生薑) Ondamtang(溫膽湯) plus rhizoma acori graminei(石菖蒲), rhizoma curcumae aromaticae(鬱金), etc., 7. The type of accumulation of stagnant blood(蓄血型) occurs when the blood is accumulated in the lower part of body. The symptoms are amnesia(健忘), chest distress(胸悶), icteric skin(身黃), rinsing the mouth but don't wanting eat(漱水不欲燕), madness(發狂), black stool(屎黑), pain in the lower abdomen(小腹硬痛). The remedy is dispersing phlegm and absorb clots (化痰化瘀), I can prescribe the recipes such as Jeodangtang(抵當湯), Daejeodanghwan(代抵當丸), Hyeolbuchugeotang (血府逐瘀湯) plus rhizoma acori graminei (石菖蒲), rhizoma curcumae aromaticae(鬱金), Jusaansinhwan(朱砂安神丸) plus rhizoma curcumae aromaticae(鬱金), radix polygalae(遠志), semen persicae(桃仁), cortex moutan radicis(收丹皮), etc., 8. The type of internal injury by seven emotion(七情所傷型) occurs when the anger injures the will stored in the kidney(腎志). The symptoms are amnesia(健忘), heart palpitation(心悸). hot temper(易怒), being easy to be scared(善驚), panic(易恐). The remedy is relieving the depressed liver and regulating the circulation of qi(疏肝解鬱). I can prescribe the recipes such as Tongultang(通鬱湯), Sihosogantang(柴胡疏肝湯) plus rhizoma acari graminei(石菖蒲), rhizoma curcumae aromaticae(鬱金), etc.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.609-617
• /
• 2000

This study is aimed at investigating an effect of HCl gas on selective reduction of NOx over a CuHM and $V_2O_5-WO_3/TiO_2$ catalyst. SCR process is the most effective method to remove NOx, but catalyst can be deactivated by the acidic gas such as HCl gas which is also included in flue gas from the incinerator. In dry condition of flue gas, the CuHM catalyst treated by HCl gas has shown higher NO removal activity than the fresh catalyst. The activity of the catalyst can be restored by treating at $500^{\circ}C$. On the contrary. $V_2O_5-WO_3/TiO_2$ catalyst is obviously deactivated by HCl and the deactivation increases in proportion to the concentration of HCl gas. The deactivated catalyst is not restored to it's original activity by heat treatment for regeneration. In wet flue gas stream, the CuHM catalyst has shown lower activity than fresh catalyst and $V_2O_5-WO_3/TiO_2$ catalyst was severely deactivated by HCl treatment. The activity loss of catalysts are mainly due to the decrease of Br$\ddot{o}$nsted acid site on the catalyst surface by $NH_3$ TPD. The change of BET surface area of CuHM catalyst after the reaction isn't observed but $V_2O_5-WO_3/TiO_2$ catalyst is observed. The amount of $Cu^{{+}{+}}$ and $V_2O_5$ is decreased after the reaction. From these results, it is expected that CuHM catalyst should be better than $V_2O_5-WO_3/TiO_2$ catalyst for its application to the incineration of flue gas.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.4
• /
• pp.211-219
• /
• 2006

The UET(ultrasound excited thermography) for the ,eat-time diagnostics of the object employs an infrared camera to image defects of the surface and subsurface which are locally heated using high-frequency putted ultrasonic excitation. The dissipation of high-power ultrasonic energy around the feces of the defects causes an increase In temperature. The defect's image appears as a hot spot (bright IR source) within a dark background field. The UET for nondestructive diagnostic and evaluation is based on the image analysis of the hot spot as a local response to ultrasonic excited heat deposition. In this paper the applicability of VET for fast imaging of defect is described. The ultrasonic energy is injected into the sample through a transducer in the vertical and horizontal directions respectively. The voltage applied to the transducer is measured by digital oscilloscope, and the waveform are compared. Measurements were performed on four kinds of materials: SUS fatigue crack specimen(thickness 14mm), PCB plate(1.8 mm), CFRP plate(3 mm) and Inconel 600 plate (1 mm). A high power ultrasonic energy with pulse durations of 250ms Is injected into the samples in the horizontal and vertical directions respectively The obtained experimental result reveals that the dissipation loss of the ultrasonic energy In the vertical injection is less than that in the horizontal direction. In the cafe or PCB, CFRP, the size of hot spot in the vortical injection if larger than that in horizontal direction. Duration time of the hot spot in the vertical direction is three times as long as that in the horizontal direction. In the case of Inconel 600 plate and SUS sample, the hot spot in the horizontal injection was detected faster than that in the vertical direction

• Journal of Korea Society of Industrial Information Systems
• /
• v.24 no.5
• /
• pp.9-16
• /
• 2019

In today's global energy market, the importance of green energy is emerging. Hydrogen energy is the future clean energy source and one of the pollution-free energy sources. In particular, the fuel cell method using hydrogen enhances the flexibility of renewable energy and enables energy storage and conversion for a long time. Therefore, it is considered to be a solution that can solve environmental problems caused by the use of fossil resources and energy problems caused by exhaustion of resources simultaneously. The purpose of this study is to efficiently produce hydrogen using plasma, and to study the optimization of DME reforming by checking the reforming reaction and yield according to temperature. The research method uses a 2.45 GHz electromagnetic plasma torch to produce hydrogen by reforming DME(Di Methyl Ether), a clean fuel. Gasification analysis was performed under low temperature conditions ($T3=1100^{\circ}C$), low temperature peroxygen conditions ($T3=1100^{\circ}C$), and high temperature conditions ($T3=1376^{\circ}C$). The low temperature gasification analysis showed that methane is generated due to unstable reforming reaction near $1100^{\circ}C$. The low temperature peroxygen gasification analysis showed less hydrogen but more carbon dioxide than the low temperature gasification analysis. Gasification analysis at high temperature indicated that methane was generated from about $1150^{\circ}C$, but it was not generated above $1200^{\circ}C$. In conclusion, the higher the temperature during the reforming reaction, the higher the proportion of hydrogen, but the higher the proportion of CO. However, it was confirmed that the problem of heat loss and reforming occurred due to the structural problem of the gasifier. In future developments, there is a need to reduce incomplete combustion by improving gasifiers to obtain high yields of hydrogen and to reduce the generation of gases such as carbon monoxide and methane. The optimization plan to produce hydrogen by steam plasma reforming of DME proposed in this study is expected to make a meaningful contribution to producing eco-friendly and renewable energy in the future.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.263-271
• /
• 2010

Intermittent CSR testing was used to investigate the degradation of an FKM O-ring, also the prediction of its life-time. An intermittent CSR jig was designed taking into consideration the O-ring's environment under use. The testing allowed observation of the effects of friction, heat loss, and stress relaxation by the Mullins effect. Degradation of O-rings by thermal aging was observed between 60 and $160^{\circ}C$. In the high temperature of range ($100-160^{\circ}C$) O-rings showed linear degradation behavior and satisfied the Arrhenius relationship. The activation energy was about 60.2 kJ/mol. From Arrhenius plots, predicted life-times were 43.3 years and 69.9 years for 50% and 40% failure conditions, respectively. Based on TTS (time-temperature superposition) principle, degradation was observed at $60^{\circ}C$, and could save testing time. Between 60 and $100^{\circ}C$ the activation energy decreased to 48.3 kJ/mol. WLF(William-Landel-Ferry) plot confirmed that O-rings show non-linear degradation behavior under $80^{\circ}C$. The life-time of O-rings predicted by TTS principle was 19.1 years and 25.2 years for each failure condition. The life-time predicted by TTS principle is more conservative than that from the Arrhenius relationship.

• The Korean Journal of Mycology
• /
• v.7 no.1
• /
• pp.13-73
• /
• 1979

These studies were conducted to investigate nutrient sources and supplementary materials of synthetic compost media for Agaricus bisporus culture. Investigation were carried out to establish the optimum composition for compost of Agaricus bisporus methods of out-door fermentation and peakheating with rice straw as the main substrate of the media. The incidence and flora of harmful organisms in rice straw compost and their control were also studied. 1. When rice straw was used as the main substrate in synthetic compost as a carbon source. yields were remarkably high. Fermentation was more rapid than that of barley straw or wheat straw, and the total nitrogen content was high in rice straw compost. 2. Since the morphological and physico-chemical nature of Japonica and Indica types of rice straw are greatly dissimilar. there were apparent differences in the process of compost fermentation. Fermentation of Indica type straw proceeded more rapidly with a shortening the compost period, reducing the water supply, and required adding of supplementary materials for producing stable physical conditions. 3. Use of barley straw compost resulted in a smaller crop compared with rice straw. but when a 50%, barley straw and 50% rice straw mixture was used, the yield was almost the same as that using only rice straw. 4. There were extremely high positive correlations between yield of Agaricus bisporus and the total nitrogen, organic nitrogen, amino acids, amides and amino sugar nitrogen content of compost. The mycerial growth and fruit body formation were severely inhibited by ammonium nitrogen. 5. When rice straw was used as the main substrate for compost media, urea was the most suitable source of nitrogen. Poor results were obtained with calcium cyanamide and ammonium sulfate. When urea was applied three separate times, nitrogen loss during composting was decreased and the total nitrogen content of compost was increased. 6. The supplementation of organic nutrient activated compost fermentation and increased yield of Agaricus bisporus. The best sources of organic nutrients were: perilla meal, sesame meal, wheat bran and poultry manure, etc. 7. Soybean meal, tobacco powder and glutamic acid fermentation by-products which were industrial wastes, could be substituted for perilla meal, sesame meal and wheat bran as organic nutrient sources for compost media. B. When gypsum and zeolite were added to rice straw. physical deterioration of compost due to excess moisture and caramelization was observed. The Indica type of straw was more remarkable in increase of yield of Agricus bisporus by addition of supplementing materials than Japonica straw. 9. For preparing rice straw compost, the best mixture was prepared by 10% poultry manure, 5% perilla meal, 1. 2 to 1. 5% urea and 1% gypsum. At spring cropping, it was good to add rice bran to accelerate heat generation of the compost heap. 10. There was significantly high positive correlation (r=0.97) between accumulated temperature and the decomposition degree of compost during outdoor composting. The yield was highest at accumulated temperatures between 900 and $1,000^{\circ}C$. 11. Prolonging the composting period brought about an increase in decomposition degree and total nitrogen content, but a decrease in ammonium nitrogen. In the spring the suitable period of composting was 20 to 25 days. and about 15 days in autumn. For those periods, the degree of decomposition was 19 to 24%. 12. Compactness of wet compost at filling caused an increase in the residual ammonium nitrogen. methane and organic acid during peak heating. There was negative correlation between methane content and yield (r=0.76)and the same was true between volatile organic acid and yield (r=0.73). 13. In compost with a moisture content range between 69 to 80% at filling. the higher the moisture content, the lower the yield (r=0.78). This result was attributed to a reduction in the porosity of compost at filling the beds. The optimum porosity for good fermentation was between 41 and 53%. 14. Peak heating of the compost was essential for the prevention of harmful microorganisms and insect pests. and for the removal of excess ammonia. It was necessary to continue fer mentatiion for four days after peak heating. 15. Ten species of fungi which are harmful or competitive to Agaricus bisporus were identified from the rice compost, including Diehliomyces microsporus, Trichoderma sp. and Stysanus stemoites. The frequency of occurrance was notably high with serious damage to Agaricus bisporus. 16. Diehliomyces microsporus could be controlled by temperature adjustment of the growing room and by fumigating the compost and the house with Basamid and Vapam. Trichoderma was prevented by the use of Bavistin and Benomyl. 17. Four species of nematodes and five species of mites occured in compost during out-door composting. These orgnanisms could be controlled through peakheating compost for 6 hours at $60^{\circ}C$.