• 대한치과교정학회지
• /
• 제20권2호
• /
• pp.381-390
• /
• 1990

The purpose of this study was to evaluate the effects of heat treatment on mechanical properties in $0.016^{{\prime}{\prime}}{\times}0.022^{{\prime}{\prime}}$ blue Elgiloy wires and to measure the amounts of nickel and chromium released from the wires in artificial saliva. Ultimate tensile strength, yield strength and elongation were measured with universal testing machine (Instron). and the amounts of nickel and chromium released from the sample were measured with atomic absorption spectrophotometer after one week immersion in the artificial saliva. Ultimate tensile strength and yield strength were progressively increased below $1000^{\circ}F$, but elongation was decreased. And the results were reversed above $1100^{\circ}F$. After heat treatment of the sample for 9 minutes at $1000^{\circ}F$, the maximum tensile strength and yield strength were $213.6kg/mm^2$, $140.1kg/mm^2$, respectively. Both tensile strength and yield strength were decreased progressively above $1100^{\circ}F$. Elongation was appeared the minimum value (8.6%) after heat treatment for 9 minutes and 12 minutes at $1000^{\circ}F$. There was a pronounced increase in nickel and chromium liberation with increasing time and temperature. The maximum amounts of nickel and chromium released form the sample were $4.947{\mu}m/cm^2$, $3.088{\mu}g/cm^2$, respectively after heat treatment for 12 minutes at $1300^{\circ}F$. Heat treatment is applied to orthodontic wires, especially cobalt-chromium alloys, for the purpose of stress-relievning and hardening. When the heat-treatment of orthodontic wires, the heating procedure should be well controlled in order to have no effect on corrosion resistance and mechanical properties.

• 열처리공학회지
• /
• 제27권2호
• /
• pp.72-78
• /
• 2014

Isothermal transformation behavior of a 10% Cr heat resistant steel fabricated by centrifugal casting process was investigated. Normalized specimen at $1100^{\circ}C$ for 1 hour was isothermally annealed at temperature range between $600^{\circ}C$ and $700^{\circ}C$ with various time. The annealed specimen had eutectoid structure which was generated along austenitic grain boundary during isothermal annealing. Areal fraction of eutectoid structure increased up to 25% after holding at $700^{\circ}C$ for 20 hours. It was observed that austenitic matrix was transformed to ferrite structure and fine $M_{23}C_6$ carbides with increase of annealing time. Time-temperature-transformation diagram of the centrifugally cast 10% Cr steel with 0.18 wt% C was plotted based on the results of isothermal transformation behavior.

• 한국유기농업학회지
• /
• 제20권3호
• /
• pp.399-409
• /
• 2012

Effects of pretreatment and extraction conditions on total polyphenol yield from licorice root were investigated using statistical method. For pretreatment, heat treatment at $121^{\circ}C$ for 10 min was applied. Licorice root content in solvent (10, 20, and 30%) ethanol concentration (20, 40, and 60%) and reaction time (1, 2, and 3 h) were used as variables for extraction conditions. Two experiments, with heat treated and no treated licorice, were prepared with same experimental design. Box behnken design was employed and produced a total of 15 trials. Total polyphenol yield from licorice root was not affected by heat treatment. Among variables, licorice content in solvent showed most significant effect regardless of other variables (p<0.05). Finally, optimum conditions for the extraction of total polyphenol from licorice root was detected as following: 10% of licorice in solvent, 52% ethanol as solvent, 2 h of reaction time and non-heat treatment and the extraction yield from optimized condition was 17.6 mg/g licorice root.

• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.457-476
• /
• 2016

본 연구에서는 목재의 열처리가공에 대하여, 문헌 연구를 통하여 이와 관련된 주요 이슈 및 기술 동향을 조사하였다. 산업적으로 이용되는 주요 열처리기술은 네덜란드의 Plato-process, 프랑스의 Retification process, 독일의 OHT-process, 및 핀란드의 Thermowood process 등이었다. 열처리 공정상의 주요 영향인자들은 대상 수종, 가열 온도, 시간, 열전달 매질(air, 증기, 진공, 질소, 오일 등)이며, 이들 인자들을 변수로 한 최적조건 탐색 등의 연구가 주류를 이룬다. 열처리 목재는 치수안정성 증가, 중량 및 강도 감소, 부후균에 대한 내후성 향상에 변이, 변색균 및 해충에 대해 불충분한 저항성 등의 특징을 가진다. 열처리 목재의 내후성 향상을 위해 각 수종에 적합한 열처리 공정과 처리조건 탐색의 필요성이 시사되었다. 지속가능한 환경보존 및 목재자원 절약을 위해 열처리 목재의 새로운 용도 개발 및 이용 확대 노력이 반드시 필요한 과제인 것으로 고찰되었다.

• 열처리공학회지
• /
• 제33권5호
• /
• pp.232-238
• /
• 2020

Heating experiments using the 7075 aluminum alloy in the state of billet and extrudate have been performed to investigate the pertinent ranges of working temperatures and holding times for the application to the various automobile parts. The 7075 specimens from raw billet of 152 mm in diameter and 400 mm in length prior to extrusion were used for heating with a holding time of 10 minutes at temperatures between 380℃ and 550℃. Then, an extrusion process using the billet has been fulfilled at 380℃ with extrusion speed of 0.8 mm/min to get an plate-type extrudate of 75 mm in width and 4.2 mm in thickness. The samples from the extrudate were subjected to heating experiments at temperatures between 380℃ and 440℃ with holding times such as 10 min, 30 min, 60 min and 120 min at each heating temperature. The microstructures were investigated on the optical and EBSD micrographs. The hardness measurement and the tensile test have been performed to investigate the effect of the heat treatment on the mechanical property. The results showed for the 7075 extrusion process that the safe heating of billet can be performed below 450℃ and the extrusion can be done safely up to 400℃.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.46-50
• /
• 2008

Super duplex stainless steel has along life in severe environments because of its strength and corrosion resistance. If 0.2$\sim$0.3% Nitrogen in aninterstitial solid solution is added, the austenite structure is reinforced. This improves the solid solution hardening and the anticorrosionability. In this study, the mechanical properties and structures of the super duplex stainless steel with the 0.2% N additive were investigated to determine the effect of various volume fractions on the austenite phase. The various volume fractions and distributions of the austenite structure in the applied test specimens were obtained by changing the heat treatment temperature and cycle. The characteristics by amounts of the $\sigma$ phase obtained from the precipitation heat treatment were alsoinvestigated. From the results, when the austenite volume fraction increases, the tensile strength decreases and elongation increases. And the $\sigma$ phase was rapidly increased by increasing the heat treatment time. When the volume fraction of the $\sigma$ phase increased, tensile strength increased.

• 한국재료학회지
• /
• 제26권5호
• /
• pp.287-291
• /
• 2016

The effect of heat treatment on the microstructure and mechanical properties of cast Ti-6%Al-4%V alloy was investigated. Heat treatment of cast Ti-6Al-4V alloy was conducted by solution treatment at $950^{\circ}C$ for 30 min; this was followed by water quenching and then aging at $550^{\circ}C$ for 1 to 1440 min. The highest hardness of the heat-treated specimens was obtained by solution treatment and subsequent aging for 5 min due to precipitates of fine ${\alpha}$ that formed from retained ${\beta}$ phase. The tensile strength of this alloy increased without dramatic decrease of the ductility due to microstructural refinement resulting from the decomposition of ${\alpha}^{\prime}$ martensite into fine ${\alpha}$ and ${\beta}$ phases, and also due to the fine ${\alpha}$ phase formed from the retained ${\beta}$ phase by aging treatment for 5 min. In addition, this strengthening might be caused by the transformation induced plasticity (TRIP) effect, which is a strain-induced martensite transformation from the retained ${\beta}$ phase during deformation, and which occurs even after aging treatment at $550^{\circ}C$ for 5 min.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.426-429
• /
• 2003

In this study, phase transformation characteristics of Nitinol shape memory alloy with 54.5wt%Ni-45.5wt%Ti were investigated by varying with annealing treatment and cutting conditions through DSC(differential scanning calorimetry). Annealing treatment conditions were considered as heat treated time of 5 min, 15 min, 30 min, and 45 min, heat treated temperature of 40$0^{\circ}C$, 50$0^{\circ}C$, 5$25^{\circ}C$, 55$0^{\circ}C$, 575$^{\circ}C$, $600^{\circ}C$, $700^{\circ}C$, 80$0^{\circ}C$, and 90$0^{\circ}C$, and environmental condition of heat treatment under vacuum or air. Cutting conditions were considered as no cutting, one side cutting, and two side cutting. Tensile test was also conducted on Nitinol shape memory alloy to investigate thermomechanical characteristics by varying with annealing heat treatment histories. According to the results, annealing treatment and cutting conditions were found to significantly affect on phase transformation and thermomechanical characteristics of Nitinol shape memory alloy.

• 한국주조공학회지
• /
• 제41권6호
• /
• pp.535-542
• /
• 2021

본 연구에서는 주철-알루미늄 이종재료의 계면결합강도를 향상시키기 위하여 탈흑연 열처리를 통해 주철 표면에서 일정 깊이까지의 흑연을 제거하였다. 열처리 시간이 증가함에 따라 흑연이 제거되는 깊이는 증가하였으며, 열처리 시간과 깊이 사이에 선형 관계가 나타났다. 일정 깊이의 흑연이 제거된 주철에 알루미늄을 다이캐스팅 공법으로 주조접합하여 주철에서 흑연이 제거된 공간을 알루미늄으로 채운 후, 계면 반응 및 알루미늄 침투 깊이를 조사하고 계면접합강도를 평가하였다. 다이캐스팅 공법을 통한 알루미늄은 탈흑연 열처리된 주철 표면에서 일정한 깊이까지 채워지는 것으로 확인되었으며, 주철-알루미늄 계면에 금속간화합물이 생성되지는 않은 것으로 확인되었다. 계면접합강도는 열처리 시간과는 큰 관계없이 90MPa 수준의 접합강도를 나타내었으며 이는 탈흑연 열처리를 하지 않은 소재의 접합강도 12MPa에 비해 매우 높은 강도이며, 주철의 탈흑연 영역에서 고압 다이캐스팅 공정에 의해 침투된 알루미늄 용탕이 응고되면서 언더컷 구조의 기계적 결합에 의한 것으로 생각된다.

• 한국레이저가공학회지
• /
• 제18권2호
• /
• pp.1-4
• /
• 2015

This study is related to the surface hardening treatment to spheroidal graphite cast iron for die by using high power diode laser. Laser device used in this experiment is capable of real-time laser power control. This is because the infrared temperature sensor (two color pyrometer) attached to the optical system measures the surface temperature of specimen and adjusts the laser power in real time. The surface treatment was carried out with the change of heat treatment temperature at the beam travel speed 3 mm/sec. Hardened width and depth was measured and hardened zone was analyzed by micro vickers hardness test in order to research the optimum condition of heat treatment. The changes in microstructure of the hardened zone also was examined. As a result of hardness measurement and observations on microstructure of hardened zone, hardness increased over three times as compared with base metal because the martensite was formed on the matrix structure.