• 한국주조공학회지
• /
• 제12권6호
• /
• pp.464-470
• /
• 1992

In the present study, the effects of Al/SiC interface reaction and the formation of $Al_4C_3$ compounds on the mechanical properties of the Al/SiC composites prepared by squeeze casting were investigated. After squeeze casting, the size of dendrites in Al without whiskers were larger than those with whiskers. The hardness of composite materials (about 72 Hv) was found to be approximating 40% higher than that of matrix metal (29Hv), which gradually increases which heat treatment Time showing maximum hardness at 12hr. The observation of increasing number of compounds in 12hrs heat treatment suggests that these compounds are responsible for the increase of hardness. By X-ray diffraction studies, those compounds were identified as $Al_4C_3$, (Al, Si). And intensity of Si peak increased. The tensile strengh of composite materials was gradually decresed by heat tretment, which was in contrast to the behavior of hardeness. With incresing heat tretment time, the fracture mode of composite materials was changed from large dimples and pull-out form of fiber to the fracture and rupture foum of fiber.

• 한국주조공학회지
• /
• 제13권5호
• /
• pp.432-440
• /
• 1993

Ductile cast iron has a good ductility and toughness than those of gray cast iron, because the shape of graphite is spheroidal. Also, it has been reported that, additional strengthening and toughening of the ductile cast iron can be obtainded from the proper combination of matrix structures by the heat treatment and addition of alloying elements. In this study the effect of special heat treatment and addition of alloying elements(Ni, Mo) on the multi-phase(ferrite-bainite-martensite) structures, strength and toughness of ductile cast iron were studied systematically. In water quenching from $770^{\circ}C$, the martensite volume(%) increased, but the ferrite volume(%) decreased with increment of Ni content. In as cast, pearlite volume(%) and hardness increased with increment of Mo and Ni contents. And with the increment of the destabilization austempering holding time, the bainite volume(%) increased but the martensite volume(%) decreased. As destabilization austempering holding time is same, bainite volume(%) decreased, martensite increased with the increment of Ni and Mo contents. The hardness and tensile strength decreased, but impact energy increased with the decrease of Ni and Mo contents, and increment of holding time of destabilization austempering treatment.

• 한국분말재료학회지
• /
• 제22권1호
• /
• pp.21-26
• /
• 2015

In this study, the control of microstructure for increasing surface roughness of Al with an electro-chemical reaction and a post treatment is systematically investigated. The Al specimen is electro-chemically treated in an electrolyte. In condition of the post treatment at $100^{\circ}C$ for 10 min, a change of the surface microstructure occur at 50V (5 min), and a oxidized layer is at 400V, to which lead a decreasing surface roughness. The minimum temperature of the post treatment for a change of microstructure is $80^{\circ}C$. Moreover, in the condition of 300V (5 min), the electro-chemical reaction is followed by the post treatment at $100^{\circ}C$, the critical enduring time for the change of microstructure is 3 min. The longer post treatment time leads to the rougher surface. The treated Al specimen demonstrate better heat release ability owing to the higher surface roughness than the non-treated Al.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.21-24
• /
• 2002

One of the factors influences on microstructure of semi-solid product is forging pressure. Generally, the more forging pressure makes the more fine microstructure in semi-solid compression test. The microstructure and mechanical properties were investigated according to the forging pressure. The applied pressure is 110MPa, 140MPa and 170MPa, respectively. Heat treatment conditions also influence to the microstructure and mechanical properties of semi-solid product. T6 heat treatment was performed and the evaluation of microstructure and mechanical properties was investigated according to the aging time in T6 heat treatment.

• 열처리공학회지
• /
• 제23권3호
• /
• pp.137-141
• /
• 2010

The Co-Cr alloys have clinical histories in dental and orthopaedic implants, and recently in cardiovascular stent applications because the alloys exhibit a high elastic modulus and radiopacity. In order to improve mechanical property of the Co-Cr alloys, electropolishing is employed as the final process. Electropolishing, an anodic dissolution process in the transpassive state, is sensitively affected by process conditions such as current density, machining time, electrode gap. In this study, the effect of heat treatment conditions on surface roughness and inclusion analysis is investigated in Co-Cr alloy (L605). The most smooth surface of Co-Cr alloy is obtained when electropolishing is performed at 15-20 V for 15-30 sec with a electrode gap of 3.5 mm.

• 한국주조공학회지
• /
• 제11권5호
• /
• pp.406-413
• /
• 1991

Ductile cast iron(DCI) with a multi-phase(ferrite-bainite-martensite) structures was produced by various special heat treatment. Intercritical heat treatment(I. C.), intermediate heat treatment(I. M.) and step quenching(S. Q.) were used to strengthen and toughen the fracture initiation sites such as graphite-marix interfaces and eutectic cell boundaries in DCI. The purpose of this study was to investigate of DCI by the special heat treatment. (I. C., I. M., and S. Q.) At a result, bainite nucleation rate at higher temperature was higher than that of at lower temperature, and shapes of bainite and martensite became bar /spheroidal type with increase of isothermal transformation time.

• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.191-194
• /
• 1997

Epitaxial Pb(Zr, Ti)O3(PZT) thin films were prepared on MgO(100) substrates by dipping-pyrolysis (DP) process using metal naphthenates as starting materials, and effects of pyrolysis and final heat-treatment conditions on the film's orientation were investigated. Solid-state epitaxial growth of PZT proceeds at lower temperature around 650℃ from the precursor pyrolyzed at 350 and 500℃. The in-plane alignment of the PZT films depends not only on the final heat-treatment temperature but on the pyrolysis conditions; the films, pyrolyzed at a higher temperature for a short time, i.e., at 500℃ for 10 min, exhibited stronger orientation after the same final heat treatment at 650°∼750℃. The PZT films with the strongest orientation were prepared by pyrolysis under the above conditions followed by final heat treatment at 750℃.

• 전기학회논문지
• /
• 제67권8호
• /
• pp.1047-1054
• /
• 2018

This paper proposed the strategies for controlling both the heater temperature and the output voltage of a single-phase inverter for the heat treatment. The single-phase inverter system for the heat treatment controls the heater temperature to its reference one, and also it limits the inverter output voltage to 60 V for safety. The stability may be deteriorated due to the large time constant difference between the heater temperature and inverter output voltage. In order to ensure the stability, a hysteresis on/off control approach for the heater temperature control is adapted, and both the open-loop and the closed-loop control strategies of the output voltage are suggested. The performances for the proposed strategies are demonstrated with the experiments.

• 한국연초학회지
• /
• 제23권1호
• /
• pp.40-44
• /
• 2001

This study was carried out to investigate relationship between contents of moisture and chemical components in burley tobacco after heat treatment. Initial moisture contents of burley tobacco was 32% after cutting and casing. Burely cut tobaccos were treated at various temperature(10$0^{\circ}C$, 13$0^{\circ}C$, 145$^{\circ}C$ and 16$0^{\circ}C$) and time(0, 5, 10, 15, 20 and 30 min) in mechanical convection oven. Moisture contents of burley tobacco after heat treatment were in the range of 1.9% to 18.4%. Relationship between moisture contents and total sugar, pH, total volatile base, ammonial, L value of color, nicotine, nornicotine, and $\beta$-nicotyrine contents were positively correlated. Correlation between moisture contents and crude ash, ether extracts, 2,6-deoxyfructosazine, 2,5-deoxyfructosazine, a value of color, citric acid, m-xylene, ${\gamma}$-butyrolactone and 5-methyl-2-furfural were negative.

• 열처리공학회지
• /
• 제6권4호
• /
• pp.213-222
• /
• 1993

This research was performed to investigate the transformation behavior and shape memory effect of Cu-13.5Al-4.5Ni(wt%) alloy with various aging temperature and time. The results obtained in this study are as follows: Transformation temperature was very increased when aging temperature is at $250^{\circ}C$. The variation of transformation temperature in first reverse transformation cycle and second was very significant, but there was little difference in case of 2nd and 3rd. Transformation temperature at various aging temperature was increased with increasing of aging temperature and time. Microvickers hardness was increased with increasing of aging temperature and time. It was found that ${\alpha}$ and ${\gamma}_2$ phase were created by aging of long time at high temperature.