• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2017

Heat treatment condition for dissolution of the M23C6 carbides in 2.25Cr-1Mo-V-Ti material for thermal power plant tube was investigated using a dilatometer method. 2.25Cr-1Mo-V-Ti material was heat-treated at $900{\sim}1,100^{\circ}C$ for 0, 10, 30 min to find the proper dissolution condition of M23C6 carbides. The phase identification and volume fraction of the carbide were measured by using OM, SEM, EBSD and TEM analysis. Optimal heat treatment condition of M23C6 carbide dissolution was selected by predicting dissolution temperature of carbide using Bs points appeared at dilatometer curve. Experimental results showed that the conditions of carbide dissolution was 900, 1,000, $1,100^{\circ}C$ for 30 min. Eventually, the optimal heat treatment condition for dissolution was 30 min at $1,000^{\circ}C$ considering the minimum coarsening of Austenite grain size.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.2
• /
• pp.168-176
• /
• 2015

This study was performed to investigate the effects of heat treatment the on mechanical properties of two species of wood under different heating conditions including at $180^{\circ}C$ for 12 h and 24 h, and at $210^{\circ}C$ for 3 h and 6 h. Two species of wood, Pinus densiflora and Larix kaempferi, were exposed to different heat treatments to assess the effects on the volume change, bending properties in static and dynamic mode and compressive strength. The results showed heat treatment caused significant changes in mechanical properties such as the static and dynamic moduli of elasticity ($MOE_d$ and $MOE_s$), and the modulus of rupture (MOR). The volume of the wood after heat treatment decreased as the heating temperature and time were increased. The bending strength performance of the wood after heat treatment decreased as the heating temperature and time were increased. The effect of heat treatment at a high temperature on the bending MOR was greater in both species than that for a long time. However, the compressive strengths of all the heat-treated samples were higher than the control sample. Furthermore, highly significant correlations between $MOE_d$ and MOR, and $MOE_s$ and MOR were found for all heating conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.4
• /
• pp.332-337
• /
• 2013

This paper presents a subsequent research work on the roller design of IRB(isolation roller bearing) seismic isolation device presented in Part 1 by focusing on heat treatment. The hardness and friction factor are very important factors of material and after-treatment process selection. Normally, roller bearing consists of roller and retainer. The roller gets high pressure constantly, while the retainer gets tensile and compressive stress. Therefore, sensitive material selection and heat treatment of each part is quite important. In this experimental evaluation, carbon steel, chrome special steel and others are employed and their characteristics after heat treatment are identified. Each material is prepared by refining high frequency heat treatment. The friction factor and static load capacity of manufactured material are experimentally identified and destructive test of material is processed. Optimal material and heat treatment conditions for IRB roller bearing are determined based on experiment results.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.2
• /
• pp.1-10
• /
• 1989

In this study, the specimens of SCM 22 H steel were quenched in oil and water baths at various agitation conditions in order to investigate the effects of quenchants and agitation conditions on the quench-hardening. A multi-channel temperature measurement apparatus was employed to obtain the cooling curves at several predetermined positions of specimens. Microstructural observation and hardness test were also carried out. Computer simulation of heat treating process was carried out using the modified finite difference method. Prediction of thermal history and hardness distribution by 2-dimensional computer analysis was in good agreement with the experimental results. It was found that the quantitative design of heat treating process can be made by the computer aided heat-treating analysis.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.2_2
• /
• pp.281-288
• /
• 2020

In this paper, we propose a control method to solve the surface hardness non-uniformity due to flow non-uniformity occurring in the heat treatment process of marine CAM. In the water cooling method including the decarbonization method, an automation device for deformation control has been developed and applied. LSTM was used to estimate the water cooling conditions, and the proposed method was found to be meaningful by improving the prototype results.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.4
• /
• pp.161-172
• /
• 2020

The tensile property of A5082 and A6060 aluminium wrought alloys was investigated, in terms of the strain rate sensitivity on alloy conditions by heat treatment and bake hardenability on pre-strain prior to strain ageing. The tensile test was carried out in a range of strain rate of 4.17 × 10^-5 s^-1 ~ 4.17 × 10^-5 s^-1 in room temperature and the nominal range of pre-strain was 3.0 ~ 10.5%. The tensile deformation of A5082 alloys is characterized as typical case of dynamic strain ageing with negative strain rate sensitivity for all conditions, and the tensile strength indicates a similar level regardless of alloy conditions, except only in full annealed condition. The stress-relief annealing on A6060 alloys can induce practical decrease in strength level of over approximately 100 MPa without any ductility loss, compared to as-rolled condition, while a full annealed and aged condition leads remarkable strengthening effect with the decrease of tensile elongation. Additionally, the bake hardenability of A5082 alloy by strain ageing indicates a negative dependence upon the increase of pre-strain, while A6060 alloy exhibits a positive sign even in low level relatively compared with conventional SPCC.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.1
• /
• pp.16-25
• /
• 2003

Recently, semi-solid forming (SSF) Process has been applied in many automobile parts for improved weight reduction, better environmental protection and energy savings. SSF process was well developed for high volume production of light weight aluminum components. In this paper, knuckle has been manufactured by SSF and then the microstructures and mechanical properties were investigated followed by various heat-treatment conditions. It was found that the examined microstructure was equiaxed at the whole cross-section area.

• 연구논문집
• /
• s.32
• /
• pp.77-84
• /
• 2002

A martensitic precipitation hardening stainless steel, 17-4PH has been widely used in the aircraft, chemical and nuclear industries for long time, owing to the excellent mechanical properties with corrosion resistance that can be achieved by simple heat treatment. The microstructure and mechanical properties of the 17-4PH stainless steel cast parts for aircraft, such as impeller, are largely affected by heat treatment condition. But the database of heat treatment has not been clearly established in the domestic investment casting industries because the domestic aerospace, industry lags behind the advanced countries. In this study, the microstructural evolution and mechanical properties of cast 17-4PH stainless steel depending on the heat treatment conditions and aging at $400^{\circ}C$ were investigated.

• Transactions of Materials Processing
• /
• v.11 no.5
• /
• pp.388-393
• /
• 2002

Heat-treatment-free steels have been replacing for conventional quenched-and-tempered structural steels since the microalloyed forging steel was developed in early 1970s in Germany. Substantial cost reduction provides the driving force for this change. As a result of intensive R & D efforts and application trials, various kinds of grades, for example heat-treatment-free steels for hot forging, machining and cold heading, have been developed and moreover these steels are in tonnage production throughout the world. The developments in alloy steels, processing conditions and structure-property characteristics of the heat-treatment-free steels, are described and also recent trend and future prospect are summarized in this report.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.552-558
• /
• 2015

The mechanical properties and microstructures of Aluminum 6056 alloys were investigated for their use in the fabrication of a piton block. The EN-AW6056 alloys exhibited a tensile strength of 375 MPa for a solution treatment temperature of $550^{\circ}C$ for 2 h followed by an aging treatment at $190^{\circ}C$ for 4 h. The microstructures of the heat treated specimen showed that the $Mg_2Si$ phase with a size of 3~5 um was dispersed throughout the aluminum matrix when the heat treatment was done. Moreover, in order to identify the forgeability of the specimen, upsetting tests were done. For up to 80 % of the upsetting ratio, the specimen maintained its original shape, and at above 80 % of the upsetting ratio, the specimen underwent crack development. The specimen was successfully forged without any defects with the examined material conditions. The material conditions together with the forging conditions are discussed in terms of the microstructures and mechanical properties.