• Toxicological Research
• /
• v.34 no.1
• /
• pp.55-63
• /
• 2018

As a part of general toxicity studies of Enterococcus Faecalis 2001 (EF 2001) prepared using heat-treatment bacillus mort body EF 2001 in mice, this study examined the toxicity of EF 2001 in single and repeated administrations following the previous report in order to apply this product to preventive medicine. The safety of oral ingestion of EF 2001 was examined in 6-week-old male and female ICR mice with 1,000 mg/kg, 3,000 mg/kg and 5,000 mg/kg body weight/day administrated by gavage of the maximum acceptable dose of EF 2001. The study was conducted using distilled water as a control following the methods for general toxicity studies described in the "Guidelines for Non-clinical Studies of Pharmaceutical Products 2002". As a control, 1) observation of general conditions, 2) measurement of body weight, 3) determination of food consumption, 4) determination of water consumption, 5) blood test and urinalysis and 6) pathological examination were performed for the administration of EF 2001. Mice received EF 2001 for 13 weeks and results were compared with those of the control group that received distilled water. The results of the above examinations revealed no significant differences between control and EF 2001 groups for both males and females. Thus, no notable toxicity was confirmed with single and repeated oral administrations of EF 2001. Oral administration in the above doses did not result in abnormal symptoms or death during the observation period. No abnormalities in blood cell count or organ weights were seen. Without any evidence of toxicity to cells and organs, EF 2001 is speculated to not adversely affect living organisms. The 50% lethal dose of EF 2001 with oral administration in mice is estimated to be greater than 5,000 mg/kg body weight/day for both male and female mice. Therefore, $LD_{50}$ value for animals was 5,000 mg/kg or more.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.373-379
• /
• 2020

In this study, TiN-coated cBN (cubic-structure boron nitride) powders were successfully synthesized by a sol-gel method using titanium (IV) isopropoxide (TTIP) and by controlling the heat treatment conditions. After the sol-gel process, amorphous nano-sized TiO_x was uniformly coated on the surface of cBN powder particles. The obtained TiO_x-coated cBN powders were heated at 1,000~1,300℃ for 1 or 6 h in a flow of 95%N₂-5%H₂ mixed gas. With increasing temperature, the chemical composition of the TiO_x coating layer changed in the order of TiO₂→Ti₆O₁₁→Ti₄O₇→TiN due to reduction of the Ti ions. The TiN coating layer was observable in the samples heated at 1,200℃ and appeared as the main phase in the sample heated at 1,300℃. The resulting thickness of the TiN coating layer of the sample heated at 1,300℃ was approximately 45~50 nm.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.6
• /
• pp.560-567
• /
• 1998

We have found that Thermoactinomyces vulgaris KFB-Cl00 produces a chitinase. The optimum temperature and pH of the enzyme activity were $55^{\circ}C$ and 6.5. The enzyme was stable after heat treatment at $80^{\circ}C$ for 30 min and stable in acidic and basic conditions (PH 6.0~11.0). The thermostable endo-chitinase from Thermoactinomyces vulgaris KFB-C100 was cloned into the plasmid pBR322 by using E. coli DH5$\alpha$ as a host strain. The positive clone carrying a recombinant plasmid (PKCHI23) with a 4.1-kb fragment containing the chitinase gene was found. The recombinant plasmid was analyzed to determine the essential region for chitinase activity and obtained a 2.3-kb fragment, which was sub cloned into pTrc99A using the PstI and SalI sites to construct pTrc99A/pKCHI23-3. The resulting plasmid exerted high chitinase activity upon transformation of E. coli XL1-Blue cells. Chitinase was overproduced 14 times more in the clone cells than in the wild-type cells and the enzyme was purified to homogeneity. The purified enzyme showed the similar properties as the native chitinase from T. vulgaris in terms of molecular weight and substrate specificity. The catalytic action of the cloned enzyme was an endo type, producing chitobiose as a major reaction product.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.12
• /
• pp.1916-1924
• /
• 2019

Outbreaks of staphylococcal food poisoning (SFP) causing serious human diseases and economic losses have been reported globally. Furthermore, the spread of Staphylococcus aureus with increased resistance to multiple antimicrobial agents has become a major concern in the food industries and medicine. Here, we isolated an endolysin LysSAP8, as one of the peptidoglycan hydrolases, derived from the bacteriophage SAP8 infecting S. aureus. This endolysin was tagged with a 6×His at the C-terminal of the target protein and purified using affinity chromatography. LysSAP8 demonstrated lytic activity against a broad spectrum of bacteria, which included a majority of the staphylococcal strains tested in this study as well as the methicillin-resistant S. aureus (MRSA); however, no such activity was observed against other gram-positive or gram-negative bacteria. Additionally, LysSAP8 could maintain bactericidal activity until 0.1 nM working concentration and after heat treatment at 37℃ for 30 min. The ability of LysSAP8 to lyse cells under varying conditions of temperature (4-43℃), pH (3-9), and NaCl concentrations (0-1,000 mM), and divalent metal ions (Ca²⁺, Co²⁺, Cu²⁺, Mg²⁺, Mn²⁺, Hg²⁺, and Zn²⁺) was examined. At the optimized condition, LysSAP8 could disrupt approximately 3.46 log CFU/ml of the planktonic cells in their exponential phase of growth within 30 min. In this study, we have suggested that LysSAP8 could be a potent alternative as a biocontrol agent that can be used to combat MRSA.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.1
• /
• pp.74-83
• /
• 2020

A number of so-called 'Type IV' cracking was reported to occur at the welded joints of the P91 steel or P92 steel reheat steam piping systems in Korean supercritical thermal power plants. The reheat steam piping systems are subjected to severe thermal and pressure loading conditions of coolant higher than 570℃ and 4MPa, respectively. In this study, piping analyses and design evaluations were conducted for the piping system of a specific thermal plant in Korea and suggestions were made how structural integrity could be improved so that type IV cracks at the welded joints could be prevented. Integrity evaluations were conducted as per ASME B31.1 code with implicit consideration of creep effects which was used in original design of the piping system and as per nuclear-grade RCC-MRx code with explicit consideration of creep effects. Comparisons were made between the evaluation results from the two design rules. Another approach with modification or reduction of the redundant supports in the piping systems was investigated as a tool to mitigate thermal stresses which should essentially contribute to prevention of Type IV cracking without major modification of the existing piping systems. In addition, a post weld heat treatment method and repair weld method which could improve integrity of the welded joint of P91 steel were investigated.

• Journal of Korea Foundry Society
• /
• v.37 no.1
• /
• pp.1-13
• /
• 2017

The purpose of this study is to increase the part recovery rate (to more than 70%) during the casting of a ductile cast iron turbo charger housing using a heater around the riser. Before creating a casting mold, various runner and riser systems were designed and analyzed with a casting simulation analysis tool. The design variables were the heater temperature, top insulation, riser location, riser diameter and the riser shape. During the feeding from the riser to the part, the reverse model was better than the forward model. When heating the riser (above $600^{\circ}C$), solidification of the riser was delayed and the feeding effect was suitable compared to that without heating. At a higher heating temperature, less solidification shrinkage and porosity were noted inside the part. On the basis of a casting simulation, eight molds were fabricated and casting experiments were conducted. According to the experimental conditions, external and internal defects were analyzed and mechanical properties were tested. The ultimate tensile strength and elongation outcome were correspondingly more than 540MPa and 5% after a heat treatment. In addition, a maximum part recovery rate of 86% was achieved in this study.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.6
• /
• pp.357-362
• /
• 2015

A novel $TiO_2$-Coconut Shell Powder Composite (TCSPS), prepared by the controlled sol-gel method with subsequent heat treatment, was evaluated as an innovative photocatalytic absorbent for the removal of methylene blue. Optimal preparation conditions of TCSPC were obtained by a response surface methodology and a central composite design model. As compared with the results obtained from one-factor-at-a-time experiments, the values were approximated to the nearest condition of these values and the following experimental parameters were set as the optimum : $600^{\circ}C$ calcination temperature and 20 g of coconut shell powder loading amount.

• International Journal of Fluid Machinery and Systems
• /
• v.5 no.3
• /
• pp.134-142
• /
• 2012

The competition to deliver ultra-low emitting vehicles at a reasonable cost is driving the automotive industry to invest significant manpower and test laboratory resources in the design optimization of increasingly complex exhaust after-treatment systems. Optimization can no longer be based on traditional approaches, which are intensive in hardware use and laboratory testing. The CFD is in high demand for the analysis and design in order to reduce developing cost and time consuming in experiments. This paper describes the development of a comprehensive practical model based on experiments for simulating the performance of automotive three-way catalytic converters, which are employed to reduce engine exhaust emissions. An experiment is conducted to measure species concentrations before and after catalytic converter for different loads on engine. The model simulates the emission system behavior by using an exhaust system heat conservation and catalyst chemical kinetic sub-model. CFD simulation is used to study the performance of automotive catalytic converter. The substrate is modeled as a porous media in FLUENT and the standard k-e model is used for turbulence. The flow pattern is changed from axial to radial by changing the substrate model inside the catalytic converter and the flow distribution and the conversion efficiency of CO, HC and NOx are achieved first, and the predictions are in good agreement with the experimental measurements. It is found that the conversion from axial to radial flow makes the catalytic converter more efficient. These studies help to understand better the performance of the catalytic converter in order to optimize the converter design.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.499-504
• /
• 2001

A validation of a 3D CFD model for predicting local subcooling of moderator in the vicinity of calandria tubes in a CANDU reactor is performed. The small scale moderator experiments performed at Sheridan Park Experimental Laboratory(SPEL) in Ontario, Canada[1] is used for the validation. Also a comparison is made between previous CFD analyses based on 2DMOTH and PHOENICS, and the current model analysis for the same SPEL experiment. For the current model, a set of grid structures for the same geometry as the experimental test section is generated and the momentum, heat and continuity equations are solved by CFX-4.3, a CFD code developed by AEA technology. The matrix of calandria tubes is simplified by the porous media approach. The standard $k-\varepsilon$ turbulence model associated with logarithmic wall treatment and SIMPLEC algorithm on the body fitted grid are used and buoyancy effects are accounted for by the Boussinesq approximation. For the test conditions simulated in this study, the flow pattern identified is a buoyancy-dominated flow, which is generated by the interaction between the dominant buoyancy force by heating and inertial momentum forces by the inlet jets. As a result, the current CFD moderator analysis model predicts the moderator temperature reasonably, and the maximum error against the experimental data is kept at less than $2.0^{\circ}C$ over the whole domain. The simulated velocity field matches with the visualization of SPEL experiments quite well.

• Applied Chemistry for Engineering
• /
• v.26 no.6
• /
• pp.706-713
• /
• 2015

Graphite foams (GFs) were prepared by adding different amounts of mesophase pitch (MP) into polyvinyl alcohol-acrylic acid (PVA-AAc) solution followed by the heat treatment. It was confirmed that the pore diameters of GFs were controlled by the slurry concentration, which was the mesophase content added in polymer solution, and their thermal conductivity and compressive strength were also controlled by porosities of GFs formed at different conditions. The resulting GFs in this study had the highest thermal conductivity of $53.414{\pm}0.002W/mK$ and compressive strength of $1.348{\pm}0.864MPa$ at 0.69 in porosity. The thermal conductivity of MP based GFs increased approximately 23 times higher than that of using isotropic pitch based GFs due to the developed graphitic structure.