• Journal of Mechanical Science and Technology
• /
• 제19권6호
• /
• pp.1378-1389
• /
• 2005

This work provides the fundamental knowledge of energy transport characteristics during very short-pulse laser heating of semiconductors from a microscopic viewpoint. Based on the self-consistent hydrodynamic equations, in-situ interactions between carriers, optical phonons, and acoustic phonons are simulated to figure out energy transport mechanism during ultrafast pulse laser heating of a silicon substrate through the detailed information on the time and spatial evolutions of each temperature for carriers, longitudinal optical (LO) phonons, acoustic phonons. It is found that nonequilibrium between LO phonons and acoustic phonons should be considered for ultrafast pulse laser heating problem, two-peak structures become apparently present for the subpicosecond pulses because of the Auger heating. A substantial increase in carrier temperature is observed for lasers with a few picosecond pulse duration, whereas the temperature rise of acoustic and phonon temperatures is relatively small with decreasing laser pulse widths. A slight lagging behavior is observed due to the differences in relaxation times and heat capacities between two different phonons. Moreover, the laser fluence has a significant effect on the decaying rate of the Auger recombination.

• 대한기계학회논문집B
• /
• 제33권8호
• /
• pp.629-634
• /
• 2009

In this paper, drying mechanism is analyzed for improving the energy efficiency of an electric clothes dryer which consumes more electric power than other appliances. For the purpose, characteristic curves of the dryer such as temperature, relative humidity, evaporation rate, mass transfer coefficient, remaining moisture content curves are experimentally obtained. Based on the experimental results and analysis of drying mechanism, the effect of power of a heater and heat loss on the power consumption of an electric clothes dryer are systematically presented. These results demonstrate the feasibility of controlling heat loss at the heater as well as the backduct component to decrease the power consumption of an electric clothes dryer.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2262-2267
• /
• 2008

In this paper, drying mechanism is analyzed for improving the energy efficiency of an electric clothes dryer which consumes more electric power than other appliances. For the purpose, characteristic curves of the dryer such as temperature, relative humidity, evaporation rate, mass transfer coefficient, remaining moisture content curves are experimentally obtained. Based on the experimental results and analysis of drying mechanism, the effect of power of a heater and heat loss on the power consumption of an electric clothes dryer are systematically presented. These results demonstrate the feasibility of controlling heat loss at the heater as well as backduct component to decrease the power consumption of an electric clothes dryer.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.62-72
• /
• 1995

The present study was undertaken to investigate the dry wear mechanism of the alumina ceramics in the purity variation for the wear of STB2. The wear test was carried out under different experimental condition various sliding speed, contact pressure and sliding distance. According as the alumina purity increased, wear volume of the STB2 decreased and minimum value of wear volume was over to high speed side. According as the sliding speed and sliding distance increased, friction coefficient decreased owing to drop of the shear strength, it decresed largely owing to decreased of elastic modulus and thermal conductivity with decrease in alumina purity. Indicative of minimum, value of wear volume, low speed side was abrasive wear, high speed side was wear of heat softening. The friction surface of ceramics protacted by oxide was transfer from STB2.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.106-106
• /
• 2012

Strategies to facilitate carrier transfer/transport while preserving confined characteristics of isolated nanocrystal quantum dots (NQDs) will be discussed. Specifically, synthesis and characterizations of 1) the fabrication of neat NQD solids (assembled NQD films) with modified surfaces by attaching ligands or by applying physical processes such as heat annealing [J. Phys. Chem. C (2011), 115(3), 607] and 2) coupling NQDs to one-dimensional nanostructures such as single-walled carbon nanotubes (SWNTs) [ACS Nano, (2010) 4(1), 324] will be presented. Further, recent achievement ours of fabricating NQDs assemblies into photovoltaic devices for elucidating transfer mechanism witll be discussed.

• 에너지공학
• /
• 제25권1호
• /
• pp.56-68
• /
• 2016

최근 원자력 발전소의 안전성을 획기적으로 향상시키기 위한 연구가 활발하게 진행되고 있으며 특히 피동냉각계통의 연구개발이 아주 중요하게 부각되고 있다. 피동냉각계통의 열전달 방식으로는 응축열전달 양식이 주로 채택되고 있다. 이와 같은 맥락에서 부산대학교 Ahn & Yun (Ahn 등, 2014)은 새로운 수평관내부 응축 모델을 제시한 바 있다. 본 연구에서는 먼저 Ahn & Yun 이 제시한 수평관 응축 모델을 MARS 코드에 삽입하고 PASCAL 실험데이터를 이용하여 평가하였다. 이 평가결과를 통해 Ahn & Yun 모델의 코드적용에 있어 문제점을 규명하고 새로운 적용방법론을 적용하여 다양한 실험데이터로 다시 평가함으로써 MARS 코드의 향상된 응축 열전달 해석 능력을 확인하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.323-324
• /
• 2012

Flammability limits of opposed flow diffusion flame in a narrow channel was investigated experimentally and theoretically. There were three different extinction modes corresponding to high strain rate (HSR), low strain rate (LSR) and dilution ratio (DR) limits. To investigate these limits, a theoretical study was followed by focusing on flow and heat transfer characteristics. Consequently, a dead space concept that has been used for premixed flames was important to reveal the heat loss mechanism in a narrow channel especially for LSR conditions even in the case of diffusion flames.

• 대한기계학회논문집B
• /
• 제20권4호
• /
• pp.1406-1415
• /
• 1996

Several recent studies have revealed that boiling heat transfer may be considerably enhanced in a narrow restricted region. In his study, the narrow restricted region was formed by attaching a perforated plate on top of a boiling surface. Through systematic experiments, effects of the hole size, hole pattern, gap width between the perforated plate and the boiling surface were investigated using water or R-113. Results show that perforated plates considerably enhance the boiling of water or R-113. For water, especially, they have outperformed commercial enhanced tubes, which confirms that boiling enhancement mechanism of the perforated plate (thin film evaporation beneath the elongated bubble) is very effective to the boiling of high surface tension liquids such as water. Optimum configuration was found - 3.0 mm hole diameter, 15 mm * 15 mm hole pattern, 0.3 ~ 0.5 mm gap width for water, and 2.0 mm hole diameter, 3.5 mm * 3.5 mm hole pattern, O.5 mm gap width for R-113. A correlation which correlates most of the data within .+-. 30% was also developed.

• 한국추진공학회지
• /
• 제9권2호
• /
• pp.89-96
• /
• 2005

성층권 비행선이 고도 20 km에서 정점 체공 시, 비행선 내외부의 수치 모델을 만들어 성층권 열환경 및 열전달을 해석하였다. 비행선의 해석 격자를 형성하였으며, 열해석 모델의 격자수와 격자형상이 해석 결과에 미치는 영향을 비교하였다. 성층권 환경에서 전도/대류/복사를 동시에 고려한 비행선 계산 결과로써 태양복사에너지로 인한 선체표면과 내부의 온도분포를 가시화 하였으며, 온도분포가 헬륨 기낭 및 탑재물에 주는 영향을 예측하였다.

• 설비공학논문집
• /
• 제16권4호
• /
• pp.349-354
• /
• 2004

Scale is formed when hard water is heated or cooled in heat transfer equipments such as heat exchangers, condensers, evaporators, cooling towers, boilers, and pipe walls. When the scale deposits in a heat exchanger surface, it is conventionally called fouling. The objective of the present study is to analyze the process of the fouling formation in a heat exchanger according to different types of water using visualization techniques. In order to experimentally investigate the formation of the fouling, this study built a lab-scaled heat exchanging system. Using the visualization techniques of Scanning Electron Microscopy (SEM) and X-Ray diffraction method, the three dimensional configurations of the fouling formation could be successfully obtained. Based on the experimental results, it was found that the configurations of the fouling formation were different when using tap water compared to river water.