• Journal of the Korea Furniture Society
• /
• v.20 no.5
• /
• pp.490-503
• /
• 2009

The objective of this work was to investigate the mechanism of heat transfer in hot-pressing process for MDF manufacturing by reference study. Firstly, general heat transfer theory was studied. The numerical analysis of heat transfer in hot-pressing process was studied on temperature profile, moisture profile, physical properties between moisture and board. The mechanism of heat and moisture transfer inside of board was analyzed by conduction, convection, radiation and diffusion of bound water in wood cell walls. Especially, the change of core temperature as hot press time was important factor to setup hot-pressing schedule in MDF manufacturing.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.5
• /
• pp.575-582
• /
• 2000

This investigation was designed to determine whether heat-pressing and/or simulated heat treatments affected the flexure strength and the microstructure of the lithium disilicate glass-ceramic in the IPS Empress 2 system. Four groups of the specimens were prepared as follows: group 1 - as-received material, group 2 - heat-pressed material; group 3 - heat-pressed and simulated initial heat-treated material; group 4 - heat-pressed and the simulated heat-treated material with full firings for a final restoration. The three-point bending test and the scanning elec-tron microscope (SEM) analysis was conducted for the purpose of this study. The flexure strength of group 2 was significantly higher than that of group 1. However, there were no significant differences in strength among group 2, 3, and 4, and between group 1 and 4. The SEM micrographs of the lithium disilicate glass-ceramic showed the closely packed, multi-directionally interlocking microstructure of numerous lithium disilicate crystals protruding from the glass matrix. The crystals of the heat-pressed materials (group 2, 3, and 4) were a little denser and about two times bigger than those of the as-received material (group 1). This change of microstructure is more obviously exhibited particularly between group 1 and 2. However, there was no a marked difference among group 2, 3, and 4 after the heat-pressing procedure. Although there were significant increase of the strength and some changes of the microstructure after the heat-pressing operation, the combination of the heat-pressing and the simulated subsequent heat treatments did not produce the increase of strength of IPS Empress 2 glass-ceramic.

• Journal of Technologic Dentistry
• /
• v.43 no.4
• /
• pp.175-180
• /
• 2021

Purpose: This study investigates the effect of repeated use of lithium disilicate glass-ceramics on color stability. Methods: In this study, 2 types of lithium disilicate glass-ceramics were used and they were divided into 4 groups after 1st, 2nd, 3rd, and 4th heat pressing. The L^*, a^*, and b^* values of all specimens were measured using the VITA Easyshade Advance 4.0. These values was used to determine the ∆E value and transparency. IBM SPSS Statistics ver. 24.0, a statistical significance level of 0.05 and one-way ANOVA were used for all data. Results: In all groups, the L^* and b^* values were the lowest in the specimens subjected to the 4th heat pressing and the corresponding a^* value was the highest. All specimens showed ∆E values of ≤3.3, indicating color changes that were not visible with the naked eye, and the color difference increased with the number of repeated heat pressing. The transparency of all specimens decreased as the number of repeated uses increased. Conclusion: According to the number of repeated heat pressing, the color difference of Rosetta SP (HASSBIO) was larger than that of IPS e.max Press (Ivoclar Vivadent), but it was clinically acceptable in all groups. Moreover, transparency decreased as the number of heat presses increased in all groups. According to the above findings, the lithium disilicate glass-ceramic has high color stability due to repeated heat pressing, implying that it can be used in clinical settings regularly.

• Journal of the Korea Furniture Society
• /
• v.24 no.1
• /
• pp.79-87
• /
• 2013

The objective of this study was to increase the utilizability of domestic thinning and small diameter wood as applying in pattern design which can be applied in interior decoration, wood craft and wood furniture, and in developing the designs of furniture and household items. Then we investigated the physical and mechanical characteristics of Acer mono wood by pressurization and heat treatment. Color change is clear, and the wood density is increased with increasing pressing rate. The compressive and bending strengths are decreased as heating time is increased after pressing. However, shrinkage is improved after pressing and heating.

• Korean Journal of Food Science and Technology
• /
• v.54 no.2
• /
• pp.179-184
• /
• 2022

In this study, edible films made of fish and mammalian gelatins were produced using heat pressing, and their physical properties were investigated. Transparent and smooth films were formed continuously and uniformly using a mixture of fish skin gelatin (FG) or mammalian gelatin (MG), glycerol, and water under the process of heat pressing at 90℃ and 20 MPa for 5 min. Heat-pressed FG films possessed lower light transmittance and tensile strength than heat-pressed MG films; however, their appearance, surface morphology, water vapor permeability, lightness, and redness were not different from those of heat-pressed MG films. Although heat-pressed FG films had lower tensile strength, they had a flatter and more uniform surfaces and demonstrated higher transparency and moisture barrier properties compared to the casted FG films. These results demonstrate the potential utility of heat pressing for the large-scale production of edible films using both FG and MG.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.2
• /
• pp.93-99
• /
• 2002

This study was performed to investigate the color stability of IPS Empress 2 glass-ceramic after heat-pressing and/or heat-treatments. Three types of IPS Empress 2 ingots (shade 100, 300, 500) were tested. For this study, three groups were prepared as follows: group 1 is as-received material, group 2 is heat-pressed material, and group 3 is fully heat -treated material. The color of the specimens was measured with a colorimeter. The data were statistically evaluated with one-way ANOVA and Scheffe's multiple test. The results obtained were as follows: 1. IPS Empress 2 glass-ceramic demonstrated less color stability according as the shade is lighter. Namely, the shade 500 showed the lowest color shifts and the shade 100 showed the greatest color shifts after heat-pressing and heat-treatments. 2. In the cases of shade 100 and 300, the changes of ${\Delta}E^*$ were affected mostly by the changes of $L^*$ and $b^*$. 3. In ${\Delta}E^*$ of the shade 100, there were significant differences among the group 1, 2, and 3 (P<0.001). 4. In ${\Delta}E^*$ of the shade 300, there were significant differences between the group 1 and 2, and the group 1 and 3 (P<0.001). 5. In ${\Delta}E^*$ of the shade 500, there was significant difference only between the group 1 and 3 (P<0.001).

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.42-45
• /
• 2007

Recrystallization behavior during ingot-breakdown process of Alloy 718 was investigated with finite element analysis and experimental approaches. In order to analyze microstructural changes during the cogging process of an Alloy 718 ingot, the side-pressing and heat treatment tests were performed at different temperatures and ram speed. From the side-pressing and heat treatment test results, it was found that microstructural changes during hot forging of Alloy 718 ingot greatly influenced on a close interaction between dynamic and static-recrystallization behaviors. A recrystallization model of Alloy 718 was used to predict the complex microstructural variation during continuous heating and forging processes of the cogging, and the predicted grain size and its distribution were compared with the actual cogged Alloy 718 billet.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.4
• /
• pp.45-58
• /
• 1987

This study was carried out to improve the physical and mechanical properties of Pupulus alba $\times$ glandulosa treated by the heat and compression. The results obtained were as follows. 1. The specific gravity of the wood was conspicuously increased by the lincreasing of pressing level. 2. The shrinkage of the wood was increased. by the increasing of pressing level. The radial shrinkage was 6.41-8.81%, the tangential shrinkage was 8.98-19.81 %, and the longitudinal shrinkage was 1.46-1.91 %. Comparing to the untreated stock, the rate of increase was 48.7-104.4% in radial direction. 1.7-124.4% in tangential direction and 60.4-109.9% in longitudinal direction, respectively. 3. The rate absorption of 30% compressed stock was Similar to that of untreated stock. but the rate of absorption of 40 % or more compressed stock was increased highly. 4. The thickness swelling of the wood was not changed in radial direction at pressing level, but was conspicuously increased in tangential direction under the pressing level of 40% and 50%. 5. The heat and compression treatment affected on the mechanical properties of the wood. The longitudinal compressive strength was increased under the pressing level of up to 40%, but was decreased under the pressing level of 50%. The bending strength was not changed under the compression percentage of up to 30%, but was decreased under the pressing level of 30% or more. And, the absorbed energy in impact bending was increased to 128% under the pressing level of up to 30%, but was decreased under the pressing level of 30% or more. Conclusionly, the mechanical properties of the wood was improved by the heat and compression treatment, but the strength of the wood was decreased under the pressing level of a certain level or more(in this study, pressing level of 30% or more). This was because of the wood deterioration due to the deformation(shrinkage, crack, failure) of wood tissues induced by the heat and compression treatment, the heat analysis of wood components induced by the heating, and the drop of the degree of polymerization.

• Journal of the Korea Furniture Society
• /
• v.23 no.1
• /
• pp.68-74
• /
• 2012

In this study domestic thinning and small diameter woods of Giant dogwood (Cornus controversa Hemsl) was used. To increase the utilizability of wood, the utilizability was proposed after manufacturing laminated wood by pressing and heating. The physical and mechanical characteristics of Laminated wood were investigated and the color change was measured, using a Chromaticity coordinates, after being pressed at 10% (45 mm), 20% (40 mm), 30% (35 mm) for 5 minutes, using Stopper, and then heated at $180^{\circ}C$ for 6, 12, 24 and 48 hours. The results were as follows. Wood density, compressive strength, MOR, MOE are increased with increasing pressing rate but decreased as heating time is increased after pressing. However, Color change is clear, dimensional stability is improved after pressing and heating.

• Journal of the Korea Furniture Society
• /
• v.25 no.2
• /
• pp.96-103
• /
• 2014

The objective of this study was to increase the utilizability of domestic thinning and small diameter wood as applying in pattern design which can be used in interior decoration, wood craft and wood furniture, and in developing the designs of furniture and household items. We investigated the physical and mechanical characteristics of Betula platyphylla Wood by pressurization and heat treatment. Color change is clear, and the wood density is increased with increasing pressing rate. The compressive strength, modulus of rupture and modulus of elasticity in bending strength are decreased as heating time is increased after pressing. However, shrinkage is improved after pressing and heating.