• Journal of the Korean Institute of Gas
• /
• v.27 no.4
• /
• pp.62-69
• /
• 2023

The use of low-grade coal is continuously increasing with the development of combustion technology and cost reduction for coal used in thermal power plants . During combustion, the latent heat of evaporation due to moisture is large, and there is a risk of spontaneous combustion and dust explosion during the process of storing and pulverizing coal. This study compared and evaluated the minimum explosive concentration and explosive strength of four types of coal dust-fine, coal dust-coarse, wood pallet+organic dust, and wood chip with coal powder collected from domestic power plant D. The minimum explosive concentration of coal dust was measured according to JIS Z 8818:2002, and the explosion strength was tested according to ASTM E1226 using a Siwek 20 L Chamber Apparatus. As a result of the minimum explosive concentration test, it was found that coal dust-fine has a risk of dust explosion, and since an explosion occurs at a dust concentration of 130 g/m³ of wood chips, it was found that there is a risk of explosion at the lowest dust concentration. According to the dust explosion class standard, Kst is less than 200 bar m/s, and all samples fall under the explosion class St 1, and the dust has a low risk of explosion.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.3
• /
• pp.134-149
• /
• 2013

The Sudang-ri Site in Geumsan is considered the historic site where Baekje dominated the inland traffic route to Gaya through Geumsan and Jinan in the 5th Century. This study identified the production techniques of iron by conducting an analysis of metallographical microstructure of the artifacts such as an iron sword and an iron sickle that were excavated in Sudang-ri Site, Geumsan, one of the regions ruled by Baekje, and tried to figure out the characteristics and the technical systems of Baekje's ironmaking around the 5th Century by comparing them with other iron artifacts produced around the same time. The analysis showed that various production techniques were applied to the artifacts excavated in Sudang-ri Site, Geumsan. Depending on the production techniques, they can be divided largely into three methods: the simple shape-forging method, the steel manufacture method after forging, and the steel manufacture & heat-treatment method after forging. The iron sickle from the stone chamber tomb No. 1, which was produced only through forging, is mostly composed of soft ferrite at both edges of the blade and at the rear making the use of the weapon impractical. From this fact, it is presumed that they were produced as burial objects or ceremonial accessories for the person buried. The iron axe from the outer stone coffin tomb No. 1 and the iron swords and sickle from the outer stone coffin tomb No. 12, which were produced through the steel manufacture method after forging such as carburizing, did not go through the heat treatment such as quenching, but applied different production processes to each part. Therefore, it is deemed that they were produced as daily tools for cultivation rather than burial objects or ceremonial accessories. The production techniques following the forging process - carburizing and heat treatment - can be found on the iron swords from the outer stone coffin tomb No. 5 and the outer stone coffin tomb No. 12. The sturdy structure of the blade part and the durable structure of the rear processed with heat are deemed to have been produced as weaponry and used by the person buried. Based on the analysis of the iron artifacts excavated from Sudang-ri Site in Geumsan, the characteristics of iron production techniques were investigated by comparing them with the artifacts from Yongwon-ri Site in Cheonan, Bongseon-ri Site in Seocheon, and Bujang-ri Site in Seosan that were made around the same time as the cluster of Baekje tombs examined by the metallographical microstructure analysis of this study. For the iron artifacts analyzed here, the changes in the techniques were investigated using the iron swords common in all of the tombs. In the case of the iron swords, it was identified the heat treatment technique called tempering was applied from the 4th Century.

• Journal of Chest Surgery
• /
• v.13 no.4
• /
• pp.338-345
• /
• 1980

We have modified an isolated perfusion rat heart model of cardiopulmonary bypass, with which we are able to screen the effects of various cardioplegic solutions and hypothermia upon the ability of the heart to survivie during and recover from period of ischemic arrest. The modified experimental model was differed from the original as follow : a heat coil chamber of atrial and aortic reservoir provided temperature control, and the perfusate was gassed with each pure oxygen and pure carbon dioxide in 95:5 ratio. The Langendorff perfusion was initiated for a 10 minute period by introducing perfusate at $37^{\circ}C.$ into the aorta from the aortic reservoir located 100 cm above the heart. The isolated perfused working rat heart model was a left heart preparation in which oxygenated perfusion medium (at $37^{\circ}C.$) entered the cannulated left atrium at a pressure of 20 cm $H_{2}O$ and was passed to the ventricle, from which it was sponeously elected(no electrical pacing) via an aortic cannula, against a hydrostatic pressure of 100cm $H_{2}O$. during this working period various indices of cardiac functin were measured. The cardiac functions were stable for over 3 hour with perfusion of Krebs-Henseleit bicarbonate buffer solution containing only glucose (11.1 mM/L). The percentage of cardiac functins were maintained about 94% on heart rate, 80.6% on peak aortic pressure, 87.7% on coronary flow and 76.3% on aortic flow rate after 3 hour of working heart perfusion at a pressure of 20 cm $H_{2}O$. We believe this preparation to be a good biochemical model for the human heart which offers many advantages including economic, speed of preparation, reproducibility, and the ability to handle large numbers.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.1
• /
• pp.1-11
• /
• 2012

This paper reports on a prototype cooling garment applying a cooling module. The cooling module was composed of a Peltier device, a cold sink, a heat sink and two fans. A constant box was used to evaluate the cooling effect of the module. Two cooling modules were attached on each side of the garment. The wear trial was conducted using 10 male subjects in an environmental chamber maintained at $30{\pm}0.5^{\circ}C$, $50{\pm}5%$RH. Subjective sensations of thermal, humidity, and comfort were surveyed. Statistical package SPSS12.0 was used for the t-test and the Wilcoxon signed-rank test. The results showed that most effective cooling module decreased the temperature of the constant temperature box by $-4.9^{\circ}C$. The micro-temperature of the cooling garment with a Peltier device was lower than the control garment during the exercise. In particular, the chest skin temperature was $1.5^{\circ}C$ lower with the cooling garment than the control. The maximum temperature difference was $-2.57^{\circ}C$ on the sides of the $1^{st}$ layer. Subjective thermal sensation from wear trials of the Peltier device attached garment was lower than the control garment. Subjects felt more comfortable with the cooling garment in almost all the periods.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.1
• /
• pp.43-55
• /
• 2013

The window ventilation system based on the heat recovery device was developed which make air ventilation possible without opening the windows. However, mechanical and aerodynamic noises were come to pass which annoyed people in rooms. In the present study, noise of new window ventilation system was measured in both general room and anechoic chamber. Also, the noise path was detected to find cause of noise generation and vulnerable area of the device. Sound absorptive and insulation materials were applied to mitigate the noise. Finally, an alternative noise control method was suggested which can satisfy with the indoor noise standards. As a result, it was shown that the cause of noise was the low transmission loss in the ventilation system. As a result, it was shown that the main noise source of the ventilation system was the blower and the major cause of noise was the low transmission loss of the ventilation system. It is also concluded that the noise levels complies with the noise standards of 40 dBA when 2 mm rubber sheet is applied inside the ventilation system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.7
• /
• pp.988-994
• /
• 2008

The purpose of the investigation was to establish how the pineal-adrenal axis plays an important role in thermoregulation in female goats under short-term heat stress. The study was conducted to observe the influence of glucocorticoids on pineal function in goats and its influence on stress alleviation capability. Melatonin and glucocorticoid secretions and several other endocrine and biochemical blood parameters reflecting the animals well being were determined over a one week period after goats had been exposed to $40^{\circ}C$ and 60% relative humidity for 10 days. Six female goats were used in the study. These animals served as self controls prior to the start of the experiment. The study was conducted for a period of seventeen days in a psychrometric chamber at $40^{\circ}C$ and 60% relative humidity. Chemical pinealectomy was achieved using propranolol followed by exogenous hydrocortisone treatment. Blood samples were drawn twice daily after each treatment to find the effect of hydrocortisone on plasma glucose, total protein, total cholesterol, cortisol, insulin, aldosterone, melatonin and corticosterone. Chemical pinealectomy significantly ($p{\leq}0.05$) affected plasma levels of the parameters studied and these could be significantly ($p{\leq}0.05$) counteracted by administration of hydrocortisone. Chemical pinealectomy aggravated thermal stress, although administration of hydrocortisone could ameliorate the condition. This indicated a role of the pineal in support of thermoregulation. The study establishes the modulating effect of glucocorticoids on pineal activity to relieve thermal stress in goats.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.4
• /
• pp.306-313
• /
• 2014

Super duplex stainless steels (sDSS) are excellent for use under severely corrosive conditions such as offshore and marine applications like pipelines and flanges. sDSS has better mechanical properties and corrosion resistance than the standard duplex stainless steel (DSS) but it is easier for a sigma phase to appear, which depresses the mechanical property and corrosion resistance, compared to DSS, because sDSS has a higher alloy element than DSS. In addition, sDSS has a feeble ductile-brittle transition temperature (DBTT) because it has a 50% ferrite microstructure. In the actual operating environment, sDSS would be thermally affected by welding and a sub-zero temperature environment. This study analyzed how precipitated sDSS behaves at a sub-zero temperature through annealing heat treatment and a sub-zero tensile test. Six types of specimens with annealing times of up to 60 min were tested in a sub-zero chamber. According to the experimental results, an increase in the annealing time reduced the elongation of sDSS, and a decrease in the tensile test temperature raises the flow stress and tensile stress. In particular, the elongation of specimens annealed for 15 min and 30 min was clearly lowered with a decrease in the tensile test temperature because of the increasing sigma phase fraction ratio.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.6
• /
• pp.413-418
• /
• 2017

In the present study, silica-aerogel-polyurethane foams were synthesized to improve the mechanical characteristics and insulation performance of the polyurethane foam applied to a liquefied natural gas carrier at a cryogenic temperature of $-163^{\circ}C$. A silica-aerogel-polyurethane foam bulk was prepared using a homogenizer by varying the weight ratio of the silica aerogel (0, 1, 3, and 5 wt%), while maintaining the contents of the polyol, isocyanate, and blowing agent constant. Compression tests were performed at room and cryogenic temperatures to compare the mechanical properties of the silica-aerogel polyurethane foams. The internal temperature of the universal testing machine was maintained through the cryogenic chamber. The thermal conductivity of the silica-aerogel-polyurethane foam was measured using a heat flow meter to confirm the insulation performance. In addition, the effect of the silica aerogels on the cells of the polyurethane foam was investigated using FE-SEM and FTIR. From the experimental results, the 1 wt% silica aerogel polyurethane foam showed outstanding mechanical and thermal performances.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.10 no.3
• /
• pp.284-288
• /
• 2005

Baker's yeast was disrupted in a 1.4-L stainless steel horizontal bead mill under a continuous recycle mode using 0.3 mm diameter zirconia beads as abrasive. A single pass in continuous mode bead mill operation liberates half of the maximally released protein. The maximum total protein release can only be achieved after passaging the cells 5 times through the disruption chamber. The degree of cell disruption was increased with the increase in feeding rate, but the total protein release was highest at the middle range of feeding rate (45 L/h). The total protein release was increased with an increase in biomass concentration from 10 to $50\%$(w/v). However, higher heat dissipation as a result of high viscosity of concentrated biomass led to the denaturation of labile protein such as glucose 6-phosphate dehydrogenase (G6PDH). As a result the highest specific activity of G6PDH was achieved at biomass concentration of $20\%$(ww/v). Generally, the degree of cell disruption and total protein released were increased with an increase in impeller tip speed, but the specific activity of G6PDH was decreased substantially at higher impeller tip speed (14 m/s). Both the degree of cell disruption and total protein release increased, as the bead loading increased from 75 to $85\% (v/v)$. Hence, in order to obtain a higher yield of labile protein such as G6PDH, the yeast cell should not be disrupted at biomass concentration and impeller tip speed higher than $20\%(w/v)$ and 10 m/s, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.942-945
• /
• 2005

Micron-sized metal wires are widely used in industries such as filtration, catalyst and composite materials, etc. In the wire drawing process, the die that is used conventionally is an effective and, at the same time, sensitive component. However, a typical array of the dies has caused many problems in the wire drawing process, e.g., large frictional force on the interface between wire and the resulting high heat generation, precise adjustment of the dies, extended cooling system, die abrasion, etc.. Because of these problems, there have been many works that are aiming at improving the efficiency of wire drawing process by analyzing the die geometry and by applying advanced die material to prolong the die life or even at developing a dieless wire drawing system. This paper is dealing with developing a new wire drawing system that is applicable to reduce the wire drawing steps with high draw ratio. The new wire drawing system does not use the dies, but use the self-induced heater that works on the basis of the resonant phenomenon of wire material. The electromagnetic wave is the heating source. The results of the study on the diameter reduction and microwave flow analysis show that the heating effectiveness of the wire is influenced by the energy distribution in the microwave propagation chamber. We can obtain diameter-reduced wires by using microwave in the dieless drawing process. Microwave as a heating source is capable of producing wires without applying dies in wire drawing process.