• 열처리공학회지
• /
• 제20권1호
• /
• pp.1-10
• /
• 2007

The deformation behaviors of full annealed and T6 treated 6061, 7075 aluminum tubes are investigated at various temperature performing uniaxial tensile test. Full annealed Al 6061 and Al7075 tubes, and T6 treated Al7075 tube don't show sharp local necking with an elongation of 50% at $300^{\circ}C$. So it is expected that influenced by elevated tempterature. At $300^{\circ}C$ and strain rate of 0.001/s, many micro-cracks are observed in T6 treated Al 6061 tube, which is believed to be responsible for the decrease of total elongation.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.62-67
• /
• 2007

The effects of the heat-treatment temperature on the carbon (C) substitution amount, full width at half maximum (FWHM) value, critical temperature ($T_c$), critical current density ($J_c$) have been investigated for 10 wt % malic acid ($C_4H_6O_5$)-doped $MgB_2/Fe$ wires. All the samples were fabricated by the in-situ powder-in-tube (PIT) method and heat-treated within a temperature range of $650^{\circ}C$ to $1000^{\circ}C$. As the heat-treatment temperature increased, it seemed that the lattice distortion was increased by a more active C substitution into the boron sites from the malic acid addition. These increased electron scattering defects seemed to enhance the $J_c-H$ properties in spite of an improvement in the crystallinity, such as a decrease of the FWHM value and an increase of the $T_c$. Compared to the un-doped wire heat-treated at $650^{\circ}C$ for 30 min, the $J_c$ was enhanced by the C doping in a high-field regime. The wire heat-treated at $900^{\circ}C$ resulted in a higher magnetic $J_c$ of approximately $10^4\;A/cm^2$ at 5 K and 8 T.

• 열처리공학회지
• /
• 제8권2호
• /
• pp.149-154
• /
• 1995

The alloying of 6.5wt % Silicon in iron decreases the magnetization and the anisotropy and minimizes the iron loss noticeably. But it is very difficult to make thin sheets because of its poor ductility which is due to an ordering reaction (body centered cubic to CsCI type crystal structure). However the ordering reaction can be suppressed by rapid solidification method. The cooling rate of rapidly solidified Fe-6.5wt % Si alloy is about $10^3K/s$ and rapidly solidified structure are fine structure, cellular structure, dendrite and equiaxed grain from surface. The precipitates of $DO_3$ Phase emerges on $B_2$ matrix and the coercive force was 0.51 Oe (50cycle, 15KGauss) in Fe-6.5wt% Si alloy which was processed by heat treatment of $1150^{\circ}C$ for 1hr in high vacuum.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1145-1153
• /
• 2011

본 연구의 목적은 극저온 열처리를 통해 Al6061 의 열처리 잔류응력을 제거하는 것이다. 이를 위해 유한요소해석을 이용하여 열처리 잔류응력을 예측하였으며, 열처리 조건에 따른 각 단계별 대류 열전달계수를 T6 와 극저온 열처리 실험을 수행하여 결정하였다. 예측된 잔류응력 결과는 X 선회절법(XRD)으로 측정된 잔류응력 결과와 비교하여 유한요소해석 결과의 타당성을 확인하였다. 또한 T6 와 극저온 열처리에 대해 각각 전기 전도도와 경도를 측정하여 기계적 특성을 평가하고 TEM 관찰과 XRD 회절 분석을 통해 석출물의 크기 및 성분을 파악하였다. 이를 통해 Al6061 의 T6 열처리와 비교하여 극저온 열처리를 적용함에 따른 잔류응력, 기계적 특성 및 미세조직변화를 조사하였다.

• 한국응용과학기술학회지
• /
• 제33권3호
• /
• pp.411-420
• /
• 2016

The objective of this study was to determine the effect of drinking water containing trimethyl glycine or ascorbic acid on growth performance and blood parameter profiles of duck exposed to scorching heat stress. A total of 480 ducks were randomly assigned to the following eight experiment groups for 42 days : control group C with general water, treatment group 1 (T1) with drinking water containing 100 ppm ascorbic acid, treatment group 2 (T2) with drinking water containing 200 ppm ascorbic acid, treatment group 3 (T3) with drinking water containing 300 ppm ascorbic acid, treatment group 4 (T4) with drinking water containing 400 ppm trimethyl glycine, treatment group 5 (T5) with drinking water containing 800 ppm trimethyl glycine, treatment group 6 (T6) with drinking water containing 1,200 ppm trimethyl glycine, treatment group 7 (T7) with electrolytes of KCl (0.5%) + $NaHCO_3$ (1.0%)+NaCl (0.5%). Our results revealed that the body weights and feed intakes of treatment groups, especially T3 and T6, were increased compared to the control group, where as the feed conversion ratios of treatment groups were decreased (p<0.05). Blood levels of total cholesterol, triglyceride, LDL-C, glucose, AST, ALT and pH in treatment groups were lower compared to those in the control group (p<0.05). Blood levels of red blood cell, platelets profiles, electrolyte and gas in treatment groups were higher compared to those of the control group (p<0.05).

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.549-550
• /
• 2006

The corrosion performance of a powder metallurgical aluminum alloy in aeronautical environments was studied for both as sintered and heat treated states. Sintered samples were obtained by uniaxial pressing of an Al-Cu-Mg prealloyed powder followed by liquid phase sintering. The heat treatments applied were T4 and T6. Corrosion behaviour was assessed by means of potentiodynamic polarization. Results for the equivalent commercial wrought counterpart, AA2024-T3, are also presented for comparison. Similar corrosion performance was observed for both as sintered and AA2024-T3 samples, while corrosion resistance of the PM materials was improved by the heat treatment, especially in the T4 state.

• 열처리공학회지
• /
• 제27권6호
• /
• pp.288-294
• /
• 2014

The study on the migration of carbon in T23/T91 dissimilar metal welds for the boiler was conducted at $600^{\circ}C$ with an increase of aging time from 1 to 100 hrs. Following results were obtained. The heavily etched dark band tended to increase from a molten boundary owing to an increase of aging time, which leads to form hard (T91) and soft (T23) zones with different hardness. It was found that carbon was migrated from T23 area to T91 area due to different carbon activities. In addition, soft and hard zones were formed in regional area mainly resulted from carbide dissolutions and precipitates.

• 열처리공학회지
• /
• 제14권6호
• /
• pp.345-349
• /
• 2001

This study has investigated the effect of thermal stability and mechanical property of $Fe_{80-X}P_{10}C_6B_4M_X$(X=2, 4, 6, M=transition metal) amorphous alloys fabricated by the melt-spun process. The glass transition temperature($T_g$), crystallization temperature($T_x$) and hardness increase with decreasing electron concentration (e/a) from about 7.38 to 7.18. The decrease of e/a implies the increase in the attractive bonding state between the M elements and other constituent element. The decrease in a/e leads to the enhancement of the attractive bonding state among the constituent elements which is favorable for the increase in $T_g$, $T_x$ and hardness.

• 소성∙가공
• /
• 제29권1호
• /
• pp.5-10
• /
• 2020

Heat treatment conditions of 88.5% asymmetrically cold rolled oxygen free copper (OFC) sheets have been studied to obtain an equiaxed fine microstructure with a grain size of less than 10 ㎛. The commercial OFC sheets with the thickness of 10 mm were asymmetrically cold rolled by using equal speed asymmetric rolling (ESAR) processes and total rolling reduction. The thickness of the rolled sheets were 88.5% and 1.15 mm, respectively. An equiaxed fine microstructure of OFC sheets with a grain size of 6.0 ㎛ were obtained when the asymmetrically cold rolled OFC sheets were heat treated at 180℃ for 40 minutes. The tensile strength of the asymmetrically cold rolled specimen increased from 217.6 MPa to 396.1 MPa, while the elongation of the specimen asymmetrically cold rolled and heat treated increased from 29.0% to 66.9% along with an 8% increase of the tensile strength.

• Asian-Australasian Journal of Animal Sciences
• /
• 제17권5호
• /
• pp.655-658
• /
• 2004

Heat stress is known to affect physiological systems in goats. This study investigated changes in nutrient digestibility, behavior and growth hormone secretion among goats in a hot environment (H; 35${\pm}$ 1.2$^{\circ}C$, [RH] 80${\pm}$7.2%, 13 d), and in a thermoneutral environment (T; 20${\pm}$0.6$^{\circ}C$, [RH] 80${\pm}$3.4%, 20 d), and accompanied by the same restricted diet as provided in the hot environment. The following results were obtained: rectal temperature and water intake were higher in the H treatment than in the T treatment or TR treatment, while hay consumption was lower. CP, NDF and ADF digestibility was highest in H treatment. Time spent eating in the H treatment was also the highest, followed in order by T treatment and TR treatment. Ruminating time was lower in H treatment than in T treatment or TR treatment, and reposing time was highest in the TR treatment. Growth hormone concentrations in T increased 4.5 h after feeding. In H, growth hormone concentrations increased 0.5 h after feeding. However, growth hormone concentrations were not changed following TR feeding. In conclusion, heat exposure in goats decreased feed intake, but increased digestibility. However, when goats in a thermoneutral environment received the same restricted feeding as they received in the hot environment, digestibility increased. Between the H treatment and TR treatment, the changes in digestibility were accomplished by coordinate changes in hormone secretion in order to maintain body homeostasis. To maintain energy balance under a hot temperature or a restricted feeding condition, goats may control their metabolism by changing growth hormone release.