본 논문은 태양열을 구동원으로 하고 액체흡수제인 염화리튬(LiCl) 용액을 이용하여 제습/냉방 및 난방을 하나의 시스템으로 이루는 태양열 이용 냉난방 공조시스템 중 여름철 전열교환기의 제습/냉방에 관한 성능실험 결과이다. 여름의 고온다습한 실내공기는 휀에 의해 전열교환기로 유입되어 충진층에서 살수된 LiCl 용액과 직접 접촉하여 제습/냉각된 후, 건조공기로 바뀌어 실내로 취출된다. 한편 수분을 흡수하여 저농도 용액으로 변한 LiCl 용액은 재생기에서 태양열에 의해 다시 고농도 용액으로 바뀌어 흡수포텐셜을 갖는다. 본 실험에서는 형상 및 크기가 다른 3가지 충진재를 사용하여 전열교환기의 제습성능을 비교하였으며, 절대습도기준 총괄 물질전달계수인 $k_xa(kg/m^3h{\Delta}x)$로써 그 성능을 평가하였다. 특히 $k_xa$값은 액체흡수제 유량, 공기 풍량, 충진재 형상 및 충진층 높이에 따라 변한다. 따라서 이에 대한 영향을 조사하기 위하여 여러 가지 실험한 결과, 풍량은 $k_xa$값에 미치는 영향이 컸으나, 유량은 그다지 영향을 미치지 않음을 알 수 있었다. 또한 충진재의 형상에 따른 비교 실험에서 충진재의 직경이 큰 경우에는 충진층 높이의 영향이 컸으나, 직경이 작은 경우에는 높이에 의한 영향이 직경이 큰 경우보다 작았다. 이상의 실험 결과로부터 $k_xa$값을 충진재 형상 및 충진층 높이에 따라 정지하면 최적 전열교환기 설계 및 제작에 기초자료로 활용할 수 있음을 알았다.
본 연구는 최근 신소재 단열재로 주목받고 있는 실리카 에어로겔을 이용하여 현재 사용되고 있는 다겹보온커튼의 단점을 보완하고 보온성을 유지 및 향상 시킬 수 있는 새로운 조합의 다겹보온커튼을 제작 하고, 보온 특성을 분석하고자 한다. 실험에 사용된 다겹보온커튼은 에어로겔이 함유된 부직포를 사용하여 총 6가지의 조합으로 제작하였으며 중량, 두께 및 온도변화에 따른 열유속을 측정하여 비교분석하였다. 실험결과 조합별 보온커튼의 열유속은 마트지+에어로겔 멜트블로운+발포 에어로겔 부직포+에어로겔 멜트블로운+마트지 조합이 가장 낮게 측정되었다. 열유속은 단위면적당 단위시간에 통과하는 열량을 뜻하며 수치가 높을수록 다겹보온커튼을 통과하는 열량이 많다는 것을 의미하여 보온성이 낮다고 판단할 수 있다. 조합형 보온커튼의 무게와 두께는 보온성과 상관이 높은 것으로 나타났으며, 특히 에어로겔 멜트블로운 부직포가 조합된 보온커튼이 같은 매수의 단열재가 조합된 보온커튼에 비해 보온성이 상대적으로 높게 나타났다. 하지만 에어로겔 멜트블로운 부직포는 내광성과 내구성이 약하고, 까다로운 제작공정과 에어로겔이 비산하는 문제점이 있다. 이러한 문제점을 해결하기 위하여 비교적 제작공정이 단순하고 보온성이 우수한 중공사 부직포와 에어로겔 발포 부직포를 조합한 다겹보온커튼이 실제 농가에서 사용하기에 적합하다고 판단된다.
본 연구에서는 해안매립지역내 벙커C유로 오염된 토양을 대상으로 토양세정 효과를 증진시키기 위한 전기저항가열의 운전인자 별 최적 조건을 도출하여 융복합 적용가능성을 평가하였다. 회분식 실험결과 Tween-80 세정제 보다 VG-2020 세정제에서 약 1.5배 이상의 높은 세정효율 보였으며, 상온 시 대비 60℃에서 약 1.4배의 세정효율 증가를 가져왔다. 전기저항가열 박스 실험결과, 함수율 20~40%의 토양에서 약 40~80분 내에 100℃까지 상승하였으며, 포화 토양층 내 STS 316재질의 파이프형 전극봉을 3각 배열 시 열전달효율이 우수한 것으로 나타났다. 또한 상기 최적조건으로 토양온도를 60℃ 이상을 유지하기 위한 전극봉의 간격은 1.5 m인 것으로 확인되었고, 전기저항가열과 동반된 토양세정 박스실험에서는 5 PV(Pore Volume)에서 약 55%의 급격한 TPH 저감효율을 보였으며 10 PV(Pore Volume)에서 토양오염 우려기준(TPH 2,000 mg/kg 미만)을 만족하였다.
The research on the flow and heat transfer characteristics of lead bismuth(LBE) is significant for the thermal-hydraulic calculation, safety analysis and practical application of lead-based fast reactors(LFR). In this paper, a new CFD model is proposed to solve the thermal-hydraulic analysis of LBE. The model includes two parts: turbulent model and turbulent Prandtl, which are the important factors for LBE. In order to find the best model, the experiment data and design of 19-pin hexagonal rod bundle with spacer grid, undertaken at the Karlsruhe Liquid Metal Laboratory (KALLA) are used for CFD calculation. Furthermore, the turbulent model includes SST k - 𝜔 and k - 𝜀; the turbulent Prandtl includes Cheng-Tak and constant (Prt =1.5,2.0,2.5,3.0). Among them, the combination between SST k - 𝜔 and Cheng-Tak is more suitable for the experiment. But in the low Pe region, the deviation between the experiment data and CFD result is too much. The reason may be the inlet-effect and when Pe is in a low level, the number of molecular thermal diffusion occupies an absolute advantage, and the buoyancy will enhance. In order to test and verify versatility of the model, the NCCL performed by the Nuclear Thermal-hydraulic Laboratory (Nuthel) of Xi'an Jiao tong University is used for CFD to calculate. This paper provides two verification examples for the new universal model.
본 연구는 젖소 경산우와 미경산우의 다양한 발정 행동 특성과 배란 시간을 조사하기 위해 수행되었다. 공시된 89두 중 73두에서 배란이 일어났으며, 이 중 61두에서 발정 발현이 나타났다. 다양한 발정 행동은 $PGF_2{\alpha}$ 투여 후 2일째부터 72시간 동안 육안 관찰하였으며, 배란 시간(4시간 간격으로 초음파 시험)과의 관계를 각각 조사하였다. 경산우의 발정 발현율은 외음부 냄새 맡기, 턱 비빔, 승가 및 승가 허용에서 각각 81%, 78%, 78% 및 56%로 나타났으며, 미경산우에서는 외음부 냄새 맡기, 턱 비빔, 승가 및 승가 허용은 각각 61%, 68%, 82% 및 76%를 보였다. 젖소 경산우와 미경산우에서 발정 개시 후 배란까지의 평균 $25.58{\pm}7.94$와 $25.55{\pm}5.72$시간이었으며, 발정 종료 후 배란까지는 평균 $13.42{\pm}7.14$와 $7.48{\pm}7.4$시간이었다. 경산우의 발정 개시 후 배란까지의 시간에서는 승가 허용($17.33{\pm}5.83$시간)이 승가, 외음부 냄새 맡기, 턱 비빔($23.58{\pm}5.12$시간, $24.25{\pm}6.09$시간, $23.42{\pm}6.04$시간)보다 유의적으로(p<0.05) 짧게 나타났으며, 미경산우에서는 유의적인 차이가 인정되지 않았다. 승가 허용 종료에서 배란까지의 시간에서는 미경산우($6.38{\pm}4.80$)가 경산우($13.05{\pm}4.53$)에 비해 유의적으로(p<0.05) 짧게 나타났다. 본 연구 결과에 의해 우유생산에 관련한 생리적인 변화가 젖소 발정행동과 배란 특성의 변화의 주요 요인일 수 있다고 사료된다.
본 연구는 급속하게 성장하는 시설농업과 동시에 증가하는 에너지 사용량 및 탄소배출량을 저감하기 위해, 온실의 에너지 부하를 동적으로 분석하기 위한 작물에너지의 다중 회귀모델 개발을 수행하였다. 온실은 연중 안정적인 대량 생산을 위한 적절한 환경을 조성하기 위해 에너지 투입이 필요하다. 도시농업의 일종인 옥상온실 플랫폼을 통해 건물에서 버려지거나 활용되지 않는 에너지를 옥상온실에서 사용할 수 있다. 옥상온실의 효율적인 운영을 위해서는 다양한 환경 조건에 대한 동적 에너지 분석이 선행되어야 하며, 온실에 도입되는 태양 에너지의 40-75%가 작물을 위한 에너지 교환이므로 필수적으로 고려되어야 한다. 한국기계연구원 내 옥상온실에서 여름철에 청경채를 재배하며 생장단계에 따른 에너지 교환을 분석하였다. 작물을 중심으로 미기상 및 양액 환경 분석과 생장 특성 조사를 수행하였다. 정식일수에 따른 엽면적지수를 추정하였으며, 개발된 수식은 결정계수 0.99로 분석되었다. 또한 작물에너지 흐름에 지배적인 잎 표면온도로부터의 현열부하와 증발산에 의한 잠열부하로 나누어 모델을 개발하였다. 엽온과 증발산량을 각각 다중 회귀모델을 이용하여 추정하고 실측한 값을 비교해 보았을 때, 평균 결정계수 0.95, 0.71로 분석되었으며, 이 모델을 이용하여 옥상온실의 에너지 부하를 동적으로 산정하기 위한 모델에 입력값으로 사용할 수 있을 것으로 판단된다.
펄스 코로나 방전에 의한 페놀 수용액 처리 특성에 관해 실험실 규모 실험을 수행하였으며 페놀 전환에 미치는 인가전압, 유입 산소, 전극 구조의 영향을 관찰하였다. 액체상 내에서 일어나는 방전은 전류 흐름으로부터 용액으로의 열전달에 의해 용액의 온도를 상승시키고 페놀을 분해하여 각종 유기산을 생성시킴으로써 pH를 감소시키며, 하전입자의 생성과 유기산 생성으로 인해 용액의 전도도 값을 증가시키는 것으로 나타났다. 외부로부터 공급되는 산소는 용액 내에서 오존 생성과 용해를 통해 OH 라디칼을 생성시킴으로써 페놀의 분해속도를 증가시키는 것으로 나타났다. 방전이 액체상 및 기체상에서 동시에 발생하는 series type의 전극 구조를 사용하면 기체상에서 높은 농도의 오존을 생성시킬 수 있으므로 액체상에서만 방전이 발생하는 reference type의 전극 구조에서보다 높은 페놀 분해 속도와 TOC 제거 효율을 얻을 수 있는 것으로 나타났다.
This experiment was carried out to study on the effect of surface coating on thermal insulation of farm structures to improve thermal resistance and reflective effect of solar radiation. Nine different types of experimental specimen were compared in the temperature variations of inside and outside; A, B, C, D. E and F types are box container and G, H and I types are drum container. The size of these containers is $1,500{\times}2,000{\times}2,500$ mm and ${\varphi}$$280{\times}330$ mm, respectively. Specimen of 3-type box(A, B, C) is galvanized steel sheet of thickness 0.45 mm. D, E and F types are sandwich panel of the thickness 50 mm inserted with urethane, glass wool and polystyrene form, respectively. G, H and I types are paint pot using in general. The surface of A. D, E, F and I types didn't any treatment, B, C and G types were treated with thermal insulation coating on the outside surface(B, G) or the inside and outside surface(C). And H type was treated with water paint coating on the only outside surface. In general, the experimental results showed the following tendencies; In case of A, B and C types. it was found that the thermal insulation effect of types coated with thermal insulation coating was improved remarkably than that of no treatment. And the thermal insulation effect between steel sheet and sandwich panel type was nearly similar There was not a significant difference of thermal insulation effect between thermal insulation coating and water paint coating. In time of drum container filled with rough rice, The difference of heat transfer tendency and temperature variation among surface treatments was nearly similar that of box types of galvanized steel sheet. And there was time lag about 6 hours between the temperature of middle part of rice and that of inside or outside surface.
To use effectively the solar energy in greenhouse heating, a high performance solar collector should be developed. And then the size of the solar collector and thermal storage tank should be determined through the calculation of heating load. The solar collector must be set in the optimum tilt angle and direction to take daily solar radiation maximally, and the flow rate of heat transfer fluid through the solar collector should be kept in the optimum range. In this research, the performance tests of a capillary tube solar collector were performed to determine the optimum water flow rate and the results summarized as follows. 1. The regressive equations for efficiency estimations of the capillary tube solar collector in the open loop were modeled in the water flow rate of 700-l,000 $\ell$/hr. 2. The optimum water flow rate of the solar collector was estimated by the second order polynomial regression and the maximum efficiency was 80% at the water flow rate of 850 $\ell$/hr. 3. The solar thermal storage system consisted of a capillary tube solar collector and a water storage tank was tested at the water flow rate of 850 $\ell$/hr in the closed loop, and obtained the solar thermal storage efficiency of 55.2%. 4. As the capillary tube solar collector engaged in this experiment was made of non-corrosive polyolefin tubes, its weight was as light as 1/30 of the flat plate solar collector made of copper tubes. Therefore it was considered to be suitable for the greenhouse heating system.
Interest in three-dimensional (3D) printing processes has grown significantly, and several types have been developed. These 3D printing processes are classified as Selective Laser Sintering (SLS), Stereo-Lithography Apparatus (SLA), and Fused Deposition Modeling (FDM). SLS can be applied to many materials, but because it uses a laser-based material removal process, it is expensive. SLA enables fast and precise manufacturing, but available materials are limited. FDM printing's benefits are its reasonable price and easy accessibility. However, metal printing using FDM can involve technical problems, such as suitable component supply or the thermal expansion of the heating part. Thus, FDM printing primarily uses materials with low melting points, such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) resin. In this study, an FDM process for enabling metal printing is suggested. Particularly, the nozzle and heatsink for this process are focused for stable printing. To design the nozzle and heatsink, multi-physical phenomena, including thermal expansion and heat transfer, had to be considered. Therefore, COMSOL Multiphysics, an FEM analysis program, was used to analyze the maximum temperature, thermal expansion, and principal stress. Finally, its performance was confirmed through an experiment.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.