• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.88.1-88.1
• /
• 2010

In recent days, the study for the renewable energy is required to supplement traditional energy source. One of the renewable energy of Fuel Cell is classified according to the electrolytes. It is the MCFC (Molten Carbonate Fuel Cell) for this study. One of the equipments of the heat exchangers is important component for efficiency and cost. In MCFC system, several heat exchangers are used according to the application. It is named for the humidifier because it is to preheat the fuel and water so that a reactor will convert some of the incoming fuel to hydrogen. Then, hot side fluid service is used the exhausted gas from the fuel cell and cold side fluid service is the fuel and water. The operation temperature range is about 25~500 Celsius Degree. This heat exchanger has the problems of heat transfer considering to multiphase fluid and phase changing. So it is necessary to analyze the heat transfer characteristics and to propose the reasonable design methodology for the humidifier. In this study, the thermal characteristic for the humidifier is estimated by using commercial tool of heat exchanger design and rating. And this study provides the testing methodology and presents the results for test facility of fabrication and for testing.

• 태양에너지
• /
• 제9권1호
• /
• pp.70-77
• /
• 1989

Sodium pyrophosphate that melting point is $79-80^{\circ}C$ have been Studied on heat storage and heat discharge. In heat storage process, sodium pyrophosphate was kept up initial temperature $50^{\circ}C,\;60^{\circ}C,\;70^{\circ}C$ which melt by heated water at temperature $85^{\circ}C,\;90^{\circ}C,\;95^{\circ}C$. In heat discharge process, initial temperature of sodium pyrophosphate was maintained at temperature $85^{\circ}C,\;90^{\circ}C,\;95^{\circ}C$ which varied cooling temperature $50^{\circ}C,\;60^{\circ}C,\;70^{\circ}C$. The experiment has been reached conclusions as follows. 1) Heat transfer properties of phase change material is controlled by conduction during heating and cooling process. 2) The temperature increased rapidly at initial stage and transient region increase slowly because of characteristic of latent heat. 3) The lower cooling water temperature is the less the time that get to thermal equivalent state take during discharge process. 4) The higher cooling water temperature is the less temperature difference between top and bottom in P.C.M during discharge process.

• 태양에너지
• /
• 제18권3호
• /
• pp.63-69
• /
• 1998

일반적으로 건물 단열재는 건조된 것이 사용되며 이 상태에서 열전도율을 측정하여 열 손실을 산정할 때 기초자료로 이용될 수 있다. 그러나 이러한 단열재가 흡습성 재료인 경우에는 습도평형 혹은 다른 작용에 의해 습도가 높아지기에 이에 따라 열전도율도 상승하게된다. 이처럼 재료 열전도율의 상승효과는 건축물에 흡습성 재료가 사용될 경우 그 사이에 비흡습성 단열재료가 시공됐을 때도 양쪽재료의 흡습성으로 인하여 단열재의 열전도율이 상승하게 되며 이에 따른 열손실 또한 높아진다. 본 논문에서는 이러한 열전도율의 상승을 간단하게 계획단계에서 적용할 수 있도록 실측에 의해 검증된 약산식을 통해 산출될 수 있도록 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.798-800
• /
• 2003

Recently, in optical storage device technical trends, the size of optical drive is slimmer to adopt notebook computer and the power of actuator is higher to achieve the high transfer rate. However, these trends of optical disc drives tend to increase the temperature of the actuator part, it causes some problems on the performance of optical parts - the resonance frequency of the actuator is down to lower band and the objective lens, coil and magnet are easily damaged. In this study, to overcome these thermal problems, the numerical simulations of heat transfer were performed. As the result of simulations, the thermal characteristic of the hybrid actuator is better than the previous design. And, it shows the good dynamic performance in experiment.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.530-533
• /
• 2010

This paper presents numerical analysis and design optimization of various turbine blade cooling techniques with three-dimensional Reynolds-averaged Navier-Stokes(RANS) analysis. The fluid flow and heat transfer have been performed using ANSYS-CFX 11.0. A fan-shaped hole for film-cooling has been carried out to improve film-cooling effectiveness with the radial basis neural network method. The injection angle of hole, lateral expansion angle of hole and ratio of length-to-diameter of the hole are chosen as design variables and spatially averaged film-cooling effectiveness is considered as an objective function which is to be maximized. The impingement jet cooling has been performed to investigate heat transfer characteristic with geometry variables. Distance between jet nozzle exit and impingement plate, inclination of nozzle and aspect ratio of nozzle hole are considered as geometry variables. The area averaged Nusselt number is evaluated each geometry variables. A rotating rectangular channel with staggered array pin-fins has been investigated to increase heat transfer performance ad to decrease friction loss using KRG modeling. Two non-dimensional variables, the ratio of the eight diameter of the pin-fins and ratio of the spacing between the pin-fins to diameter of the pin-fins selected as design variables. A rotating rectangular channel with staggered dimples on opposite walls are formulated numerically to enhance heat transfer performance. The ratio of the dimple depth and dimple diameter are selected as geometry variables.

• 대한기계학회논문집B
• /
• 제23권10호
• /
• pp.1327-1339
• /
• 1999

Characteristics of two-phase flow and heat transfer were numerically investigated in a submerged gas Injection system. Effects of both the gas flow rate and bubble size were investigated. In addition, heat transfer characteristic and effects of heat transfer were investigated when temperature of the injected gas was different from that of the liquid. The Eulerian approach was used for the formulation of both the continuous and the dispersed phases. The turbulence in the liquid phase was modeled by the use of the standard $k-{\varepsilon}$ turbulence model. The interphase friction and heat transfer coefficient were calculated by means of correlations available in the literature. The turbulent dispersion of the phases was modeled by introducing a "dispersion Prandtl number". The plume region and the axial velocities are increased with increases in the gas flow rate and with decreases in the bubble diameter. The turbulent flow field grows stronger with the increases in the gas flow rate and with the decreases in the bubble diameter. In case that the heat transfer between the liquid and the gas is considered, the axial and the radial velocities are decreased in comparison with the case that there is no temperature difference between the liquid and the gas when the temperature of the injected gas is higher than the mean liquid temperature. The results in the present research are of interest in the design and the operation of a wide variety of material and chemical processes.

• 한국자기학회지
• /
• 제12권2호
• /
• pp.73-79
• /
• 2002

자성유체는 고액혼상유체로 뉴턴유체와 달리 자기력에 반응하는 유체이다. 본 연구에서는 금속과 유체의 특성을 겸비한 자성유체의 열전달 특성을 밀도 있게 연구함을 목적으로, 그 대상을 이중원관으로 하여 열대류현상을 고찰하기 위해 내부원관을 가열하고, 외부원관을 냉각하면서, 또한 외부에서 인가자장의 세기와 방향에 따라 자연대류 현상의 변화 및 열전달 특성을 수치해석적으로 연구하여, 실험결과와 비교 검토하였다. 자성유체의 자연대류현상은 인가자장에 따라 제어할 수 있었고, 평균 뉴셀트수를 구한 결과로서 자장을 가하지 않았을 경우와 비교해 보면 열전달은 자장을 중력방향으로 가하거나 중력과 반대방향으로 그세기를 -14 mT이상 가했을 때 증가하였고, 중력과 반대방향으로 감했을 때 감소하였다. 특히 자장의 세기가 -14 mT가 되면 열전달은 최소가 되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권2호
• /
• pp.224-231
• /
• 2011

핀-휜 구조물이 삽입된 채널은 열전달이 향상되는 것으로 알려져 있다. 복잡한 핀-휜 구조물은 다공성 매체로 모사할 수 있을 만큼 매우 불규칙적인 유동을 보여준다. 본 연구는 수치해석을 통하여 핀-휜 구조물이 삽입된 채널의 열전달과 압력강하의 특성을 분석하였다. 유효유동공간비가 높고 직경이 큰 경우 실험데이터를 잘 예측 하였지만, 유효유동공간비가 낮은 경우 비교적 오차가 큰 편이었다. 유효유동 공간비가 낮을수록 유동교란이 강해져서 열전달이 증가하지만 압력강하도 증가하여 팬의 동력이 증가하기 때문에 최적점을 찾아서 설계하여야 한다. 본 연구에서는 전면유속이 5m/s 일 때, D25 모델에서는 유효유동공간비가 0.5인 지점에서, D05 모델에서는 0.9에서 압력강하가 급격하게 늘어나기 때문에 이보다 더 작은 유효유동공간비에서의 작동은 바람직하지 않다.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.685-692
• /
• 1991

The pool boiling behavior of a heated surface has been investigated experimentally, focusing on the cases when only a part of the contact surface is heated. Characteristic boiling curves are obtained with circular metal surface test pieces heated below while immersed in Refrigerant-113. Locally heated test pieces are fabricated by inserting a heating block at the center inside a larger conducting block. Overall heat transfer rates are measured while the experimental conditions are systematically varied. The local temperature profiles along the radius are measured for conducting blocks. It is found that the conjugated boiling condition exists and the total heat fluxes should be correlated to a suitably defined temperature difference.

• Journal of Mechanical Science and Technology
• /
• 제20권3호
• /
• pp.382-390
• /
• 2006

The present study proposes a modified temperature-dependent non-Newtonian viscosity model and investigates the flow characteristics and heat transfer enhancement of the viscoelastic non-Newtonian fluid in a 2:1 rectangular duct. The combined effects of temperature dependent viscosity, buoyancy, and secondary flow caused by the second normal stress difference are considered. Calculated Nusselt numbers by the modified temperature-dependent viscosity model give good agreement with the experimental results. The heat transfer enhancement of viscoelastic fluid in a rectangular duct is highly dependent on the secondary flow caused by the magnitude of second normal stress difference.