• 한국기계가공학회지
• /
• 제12권5호
• /
• pp.76-85
• /
• 2013

This study was carried out to investigate the relation between surface roughness and heat absorption capability of materials for solar collector. For this purpose, 3 kinds of materials (copper, aluminum, iron), 5 kinds of surface roughness (scrubber, alumina sand #80, #200, #400, glass bead) and 2 kinds of surface treatment (black chrome plating, copper black coating) were used for finding optimal conditions to apply solar collector. As the results, it was confirmed that the optimal relations between surface roughness and surface treatment as well as optimal materials were necessary. Further, heat absorption capability was showed good results in cases of copper materials, glass bead and black chrome plating.

• Journal of the Korean Wood Science and Technology
• /
• 제46권2호
• /
• pp.149-154
• /
• 2018

The changes in sound absorption capability and air permeability of Malas wood after high temperature heat treatment were investigated. The average air permeability of Malas in longitudinal direction after heated under the temperature of $190^{\circ}C$ during 3 hours was about 23.48 darcys and that of control was about 3.11 darcys. The noise reduction coefficients of Malas specimens were 17% for treatment and 10% for control. The means of sound absorption coefficient of specimens in the frequency range of 50~6,400 Hz were 42% for treatment and 17% for control, respectively.

• 설비공학논문집
• /
• 제7권2호
• /
• pp.196-206
• /
• 1995

Experimental investigations on heat and mass transfer characteristics in a vertical tube absorber have been carried out. Three different copper tubes with a length of 1.5m have been tested using LiBr solution and LiBr-$CaCl_2$ solution. The effects of solution flow rate, cooling water temperature, solution inlet temperature and evaporation temperature have been investigated in detail. It is found that heat transfer coefficient increases gradually with the increase of solution flow rate, but decreases rapidly for the flow rates less than 0.02kg/ms. The grooved tube generally shows better heat transfer performances than the smooth tube. LiBr solution shows almost no absorption capability for the cooling water temperatures over $40^{\circ}C$. LiBr-$CaCl_2$ gives less decreasing rate in absorption capability at these temperatures and the heat transfer coefficient becomes less dependent on the types of tubes in use. Considering heat and mass transfer rates, LiBr-$CaCl_2$ solution is found to be more suitable than LiBr solution for air cooled absorber, which operates at higher temperature than water cooled absorber.

• 대한금속재료학회지
• /
• 제46권9호
• /
• pp.572-576
• /
• 2008

Elastostatic compression tests were carried out on amorphous alloys to evaluate their energy absorption capability during homogeneous deformation at room temperature. Experiments demonstrated that a compressive stress below the global yield imposed on amorphous alloys for extended periods causes homogeneous plastic strain associated with the irreversible structural disordering. During the disordering process, free volume was created, dissipating the externally applied strain energy and the rate of creation was found to converge to a saturated value. We evaluated the capability of energy absorption of amorphous alloys during homogeneous deformation using recent theories on the evolution of the structural state.

• 한국가스학회지
• /
• 제3권1호
• /
• pp.14-20
• /
• 1999

[ $H_2O/LiBr$ ]계 흡수식 사이클에 압축기를 조합한 흡수압축사이클을 도입하여 증기를 단열압축시켜 그 증기의 응축열을 재생열로 이용하는 사이클에 대해서 시뮬레이션을 통하여 횹수압축사이클의 특성을 밝힌 연구이다. 기존의 흡수사이클에 압축기를 도입함에 따라 고효율 사이클을 실현할 수 있음을 제시하였으며, 흡수$\cdot$압축사이클의 구체적인 가능성을 제시하였다. 재생기에서 발생한 냉매증기를 단열압축시킨 TYPE 2는 단열압축 증기의 응축열만으로는 재생이 어려우므로 외부로부터 별도의 열량을 투입해야 하며 투입하는 외부열량에 폐열이나 2차 에너지를 이용할 수 있다면 높은 COP를 얻을 수 있어 실현가능성이 높다.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 1998년도 추계학술발표회 논문집
• /
• pp.255-260
• /
• 1998

This study describes the results of Coefficient Of Performance(COP) analysis by cycle simulation for two types of absorption-compression hybride cycle using the water/Lithium Bromide solution pair, These types are basic hybride systems introducing a mechanical compression process into the refrigerant vapor phase of the single effect absorption cycle. In absorption-compression hybrid cycles, coefficient of performance is improved compared with absorption cycle. Hybride cycle Type ll is considered as a key technology to support energy utilization system, given its capability of utilizing waste heat to drive system with a high level of efficiency.

• 설비공학논문집
• /
• 제20권1호
• /
• pp.49-56
• /
• 2008

When the outdoor air temperature decreased less than the freezing temperature, frost forms at the surface of heat exchangers and it makes the performance degradation of a heat pump system. In this study, a heat pump system has been developed which has a refrigerant heating device as an auxiliarly heating equipment. To reduce power consumptions of the system, a liquid pump, rather than a compressor, was used to drive refrigerant in the heat pump cycle. Ratio of refrigerant mass flow between a refrigerant heating heat exchanger(GHX) and a outdoor plate heat exchanger(PHX) was varied and the system performance was measured and analyzed. As results, when the refrigerant flow rate to the GHX was decreased, the system performance is decreased due to heat absorption capability restriction of the GHX and small variation of the power consumption in the compressor. The effect on the evaporating and condensing pressure by the distribution ratio of the refrigerant to the each heat exchanger is small compare to the effect by the frequency change in the compressor. When the compressor was replaced by the liquid pump, the capacity of the system decreased a little, however the power consumption decrease approximately 80% compare with the power used in the compressor.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.77.2-77.2
• /
• 2015

Recently, metamaterials attracted much attention because of the potential applications for superlens, cloaking and high precision sensors. We developed several dielectric metamaterials for enhancing antireflection or light trapping capability in solar energy harvesting devices. Colloidal lithography and electrochemical anodization process were employed to fabricate self-assembed nano- and microscale dielectric metamaterials in a simple and cost-effective manner. We improved broadband light absorption in c-Si, a-Si, and organic semiconductor layer by employing polystyrene (PS) islands integrated Si conical-frustum arrays, resonant PS nanosphere arrays, and diffusive alumina nanowire arrays, respectively. We also demonstrated thin metal coated alumina nanowire array which is utilized as an efficient light-to-heat conversion layer of solar steam generating devices. The scalable design and adaptable fabrication route to our light management nanostructures will be promising in applications of solar energy harvesting system. On the other hands, broadband invisible cloaks, which continuously work while elastically deforming, are developed using smart metamaterials made of photonic and elastic crystals. A self-adjustable, nearly lossless, and broadband (10-12GHz) smart meatamaterials have great potentials for applications in antenna system and military stealth technology.

• 한국수소및신에너지학회논문집
• /
• 제23권1호
• /
• pp.8-18
• /
• 2012

This paper presents a three-dimensional, transient cold-start polymer electrolyte fuel cell (PEFC) model to numerically evaluate the effects of membrane electrode assembly (MEA) design and cell location in a PEFC stack on PEFC cold start behaviors. The cold-start simulations show that the end cell experiences significant heat loss to the sub-freezing ambient and thus finally cold-start failure due to considerable ice filling in the cathode catalyst layer. On the other hand, the middle cells in the stack successfully start from $-30^{\circ}C$ sub-freezing temperature due to rapid cell temperature rise owing to the efficient use of waste heat generated during the cold-start. In addition, the simulation results clearly indicate that the cathode catalyst layer (CL) composition and thickness have an substantial influence on PEFC cold-start behaviors while membrane thickness has limited effect mainly due to inefficient water absorption and transport capability at subzero temperatures.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권2호
• /
• pp.122-129
• /
• 2019

콘크리트 구조물에서 균열은 수축, 수화열 및 외부하중 등에 의해 발생하는 불가피한 현상으로, 외부 유해인자를 콘크리트 내부로의 침투를 용이하게 하여 내구성을 크게 감소시킨다. 최근 스스로 균열을 치유하는 자기치유 콘크리트에 대한 연구가 활발히 수행되고 있다. 또한 콘크리트에 발생하는 균열을 제어하여, 그 성능을 극대화하기 위한 자기치유 섬유 보강 콘크리트의 연구가 수행되고 있다. 본 연구에서는 PVA 섬유를 혼입한 자기치유 모르타르를 제작하였다. PVA 섬유 혼입율에 따른 압축강도 및 휨 성능 평가를 수행하였다. 또한, 흡수율 실험을 통해 자기치유 성능평가를 수행하였으며, 시간에 따라 균열 폭의 감소로 흡수되는 수분의 양이 감소하는 것을 확인하였다. 자기치유 생성물 분석을 통해 PVA 섬유 혼입에 의해 탄산칼슘 침전이 더 유리한 것으로 확인되었다.