• 한국산업보건학회지
• /
• 제8권1호
• /
• pp.36-49
• /
• 1998

The purpose of this study is to investigate the relationship between the work postures and upper extremity cumulative trauma disorders(CTDs) in female medical insurance bill reviewers(n=448). This study included diagnosis for CTDs, anthropometry and job analysis (workstations and posture). The characteristics of subject were 33.6 years of average age and 8.7 years of average work duration. The results were as fallows. Ergonomic conditions of workstation were unsuitable compared with anthropometry result. The height of work surface(79.5 cm) and chair(43.0 cm)were high. work space was small, and legs space under the table was limited. Work postures were awkward compared with recommended neutral postures. Neck flexion($21.0-36.0^{\circ}$), elbow elevation, shoulder abduction ($46.0-47.0^{\circ}$). wrist radial and ulnar deviation, forearm supination and pronation, and wrist repeated motion(12.7-21.5 freq./min) were analyzed as hazardous risk factors by job analysis. The prevalence of CTDs was 32.8 % by medical diagnosis. The prevalence rate of CTDs in hazardous work posture group was significantly greater than safe work posture group both neck-shoulder (relative prevalence = 5.2, p<0.001) and wrist-hand (relative prevalence = 2.5, p<0.05).

• 한국안전학회지
• /
• 제12권4호
• /
• pp.161-168
• /
• 1997

Most plants producing semiconductors use a lot of chemicals, hazardous materials, and explosive gases. Though those materials are hazardous too much, some works still have to be done manually by human workers. However, according to a historical survey, more than half industrial accidents of those plants resulted from human errors or malfunctions. Thus, this research aimed 1) to diagnose shifting hazardous materials of semiconductor plants, 2) to estimate failure probability of human workers through human reliability analysis, and 3) to find out the tasks on which educational emphasis should be put. Through personal interview and visiting working spots, shifting tasks were analyzed, and modelled into a 24-step work, and after that, THERP and ETA was applied. During the shifting work, estimated human failure probability under the assumption of independency, 2.3004E-05, underestimated that probability 8. l008E-05 which could be calculated under the assumption of dependency. And this analysis showed that gas leakage from an old cylinder occupies 78.27% in the case of independent failures whereas gas leakage from a new cylinder occupies 75.06% in the case of dependent failures. So it was concluded that dependency assumption may gloss real situations. In addition, confirming gauge of regulators and closing valves turned out to be the most important tasks than purge tasks.

• 대한치위생과학회지
• /
• 제5권2호
• /
• pp.1-11
• /
• 2022

Background: This study was aimed at investigating the type of work of dental hygienists and identifying factors affecting the subjective health status according to hazardous risk factors in the working environment. Methods: From May 15 to 31, 2019, we surveyed 411 dental hygienists working at dental hospitals in the metropolitan area. SPSS 25.0 was used to perform the frequency analysis, t-test, one-way analysis of variance, Pearson's correlation analysis, and multiple regression analysis. Results: Regarding factors related to the degree of exposure to hazardous risk factors in the work environment and subjective health status, the more exposed the ergonomic (p<0.05) and psychological (p< 0.001)factors, the worse is the subjective health status. Conclusion: The results of this study suggest that the working environment should be improved for dental hygienists such that they can perform their duties in a safe environment.

• 한국산업보건학회지
• /
• 제34권1호
• /
• pp.1-7
• /
• 2024

Objectives: The study was performed to investigate characteristics of hazardous factors regarding chemical(liquid lime) tank dredging workers by case survey. Methods: Field data such as working condition, MSDS and respirators applied to chemical tank dredging work were analyzed and the work environmental factors of noise and indoor air quality were measured to compare existing data with actual work situations. Results: No health hazards to workers due to working conditions were confirmed during dredging work inside the chemical storage tank. All air quality measurement data during dredging work satisfied the management standards, and there were no by-products. During dredging work, there was a significant change in noise depending on the type of work, but considering the noise reduction rate(NRR) of the earplugs worn by workers, there was no actual health hazard due to noise exposure. Conclusions: A fit test for respirator and the expiration date of the safety helmet should be observed to ensure an appropriate level of safety and health for dredging workers in the chemical storage tank.

• 한국학교ㆍ지역보건교육학회지
• /
• 제17권1호
• /
• pp.59-73
• /
• 2016

Objectives: The working environment affects employees' physical and mental aspects, and has a deep associations with depression. The purposes of this study are to investigate how hazardous environment working experience impacts on depression, to provide rationale and practical implications for reducing depression and drinking. Methods: This study targeted 215 dental hygiene students from 3 universities located in Gyeonggi-do from November 30 to December 4, 2015. We analyzed the data with frequency analysis, descriptive statistics, t-test. One-way ANOVA, Pearson correlation coefficient, Regression analysis by using SPSS. Results: This study showed that experience working in hazardous environments increased depression and alcohol drinking, on the other hand alcohol drinking reduced depression. In addition, experience working in hazardous environments effected on depression indirectly through mediating of drinking, subjective health had not role of Moderating Effects between experience working in hazardous environments and depression. Conclusions: In order to reduce workers' depression and alcohol, the improvements of harmful environment are needed. For this governments and local governments should efforts to support enhancing workplace environment, to develop model of standard work environment, and to change employers' awareness on the harmful environment.

• 한국의류산업학회지
• /
• 제15권3호
• /
• pp.452-460
• /
• 2013

This study conducted a performance evaluation of protective clothing materials used for welding in a hazardous shipbuilding industry work environment. The welding process was selected as the one that most requires industrial protective clothing according to work environment characteristics. Flame proofing and convection heat protection performance (HTI) in the heat transfer characteristics of protective clothing material were indicated in the order of SW1(Oxidant carbon)>SW2(silica coated Oxidant carbon)>SW4(Oxidant carbon/p-aramid)>SW3(flame proofing cotton). However, radiant heat protection performance (RHTI) and the heat transfer factor (TF) were indicated in the order of SW1>SW4>SW2>SW3 and showed different patterns from the convection heat protection performance. SW1 showed superior air permeability and water vapor permeability. The tensile strength and tear strength of welding protective clothing material were indicated in the order of SW4>SW2>SW3>SW1 and showed that a blend fabric of p-aramid was the most superior for the mechanical properties of SW4. SW1 had excellent heat transfer properties in yet met the minimum performance requirements of tensile strength proved to be inappropriate as being a material for welding protective clothing. The abrasion resistance of woven fabric proved superior compared to nonwoven fabric; however, seam strength and dimensional change both met the minimum performance requirements and indicated that all samples appeared non-hazardous. Finally, oxidant carbon/p-aramid blend fabric appeared appropriate as a protective clothing materials for welding.

• 한국산업보건학회지
• /
• 제34권2호
• /
• pp.156-165
• /
• 2024

Objectives: This study aims to identify and analyze the exposure status of welding students in specialized high school welding labratories, compare it with the exposure to welding hazards of industrial workers, and seek to improve the educational environment for youth through domestic and international exposure standards. Methods: This study compares the level of exposure to hazardous factors in a welding laboratory of a vocational high school in Jeollanam-do and a welding process in a general industrial site by measuring the work environment. A 10-question survey was conducted to review the effects of welding hazards on the human body, carcinogenicity information, international (US, UK, France) exposure standards, general characteristics between the two groups, and awareness of occupational health. Results: Exposure to hazardous factors in both groups was below the standards set by MOEL. Specialized high school students were exposed to higher levels than workers, and some hazardous factors exceeded the standards when compared to international exposure standards. During the survey, students were less aware of the hazards of welding, safety and health education, and the need for work environment measurement than workers. Conclusions: For the respiratory protection of students in vocational high school welding labs, it is necessary to create a comfortable training environment. Exposure standards for harmful factors should be strictly applied, such as overseas standards, or exposure should be limited by setting a limit on the number of hours of welding practice per week. In addition, it is necessary to conduct safety and health education for welding students to raise their awareness of the importance of measuring the working environment and wearing appropriate protective equipment.

• Korean Chemical Engineering Research
• /
• 제52권6호
• /
• pp.736-742
• /
• 2014

사고대비물질 취급 사업장에서 사고가 발생하면 일반 화학물질사고보다 더 많은 인명, 재산피해를 야기한다. 사고를 예방하기 위해 여러 시스템들과 제도들을 개발하고 있지만, 사고발생의 주원인인 작업자의 오류를 제거 또는 감소시키기 위한 기술들은 미흡한 실정이다. 본 논문에서는 2012년 9월 구미 불산 누출사고 case study를 통해 국내기술지침들을 기반으로 위험작업 수치화 및 잠재위험확인, 작업평가를 수행하였으며 기존 시스템들을 보완하기 위한 새로운 risk mapping 방법론 개발에 관한 연구를 진행하였다.

• 한국산업보건학회지
• /
• 제28권4호
• /
• pp.393-405
• /
• 2018

Objective: This study examines the types of hazardous factors in the working environment and the time-trend for their exposure levels over 10 years (2007 to 2016). Study Design and Method: The types of hazardous factors and exposure levels were drawn from the 19 measurement reports on the working environment over 10 years at a shock absorber manufacturing facility. Risk assessment of the types of factors and time-trend of exposure levels were evaluated using the factors and exposure levels. Results: A total of 34 hazardous factors were evaluated. The types were noise, 15 organic compounds, seven kinds of acid sand alkalis, eight kinds of heavy metals, and three other compounds. Special management materials used were nickel, hexavalent chrome, and sulfuric acid. Human carcinogens (1A) used were trichloroethylene, nickel, and sulfuric acid. There were six types of substances belonging to the IARC's 2B (body carcinogens) classification or higher, including, methyl isobutyl ketone, ethyl benzene, and trichloroethylene. No detection was found for 627 out of the 2065 total measurements in 19 exposure survey reports, representing 30.4%. Organic solvents, acid and alkali products, and heavy metals showed continuous low exposure concentrations. Noise, welding fumes, and the evaluation of mixed solvents show a gradual decrease in geometric mean and maximum over the time-trend of 10 years. Conclusions: In the case of a shock absorber manufacturing facility, the hazardous factors of noise and the evaluation of mixed solvents still indicate high concentrations exceeding the exposure limits and necessitate reduction studies. These two factors and welding fumes showed a continuous decrease in their ten-year tendency. Organic compounds, acids/alkalis, and heavy metals were managed smoothly in a work environment of continuous low concentrations.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.246-251
• /
• 2005

Accident scenarios analysis is a course to understand, analyze, and describe a process of an accident and behavior pattern of the parties to an accident. The method of accident scenarios is that we described patterns represented between accidents and hazardous conditions, and then provide data to prevent the accident. We have carried out scenarios analysis in various fields so far, but it was not taking account of system. In this research, we made a study on technology of accident scenarios analysis using QFD (Quality Function Deployment) to analyze systematically and evaluate quantitatively types of hazards and scenarios of railway accident. And we analyses accident scenarios of a subject of work-related fatality accident to railway employee and conducted risk assessment for different scenarios. Also we defined relation between unsafe events and hazardous conditions caused to work-related fatality accident, and attempted to quantitatively assess work-related fatality accident and the parties to accidents. The results of this research will be used in analyzing for important causes and contributing factors of work-related fatality accidents at the step of risk assessment of railway system, and quantitatively assessing frequency of work-related accidents and risk.