• 한국가스학회지
• /
• 제17권6호
• /
• pp.27-32
• /
• 2013

바이오가스, 매립가스와 같은 신재생 가스 연료는 Biomass, 유기성 폐기물 등으로부터 얻을 수 있기 때문에 대기 중의 이산화탄소를 증가시키지 않고 재순환시키는 탄소중립적인 특성이 있어 지구온난화에 대응할 수 있는 장점이 있다. 따라서 다량의 불활성가스로 인한 저발열량, 원료 및 공정에 따른 연료조성 변화 등의 단점에도 불구하고 이를 엔진에 적용하여 에너지를 생산하고자 하는 노력이 계속되어왔다. 이중에서도 연료조성의 변화는 엔진 성능에 큰 영향을 미칠 수 있기 때문에 이에 대한 연구가 필요한 실정이다. 따라서 이번 연구에서는 신재생가스연료에 포함된 불활성가스의 양을 변화시켜 연료 조성 변화를 모사하고 이를 엔진의 연료로 사용함으로써 연료 조성의 변화가 엔진 성능 및 배기배출 특성에 주는 영향을 파악하였다. 또한 엔진 효율 및 배기 성능을 향상시키기 위한 방안에 하나로 보다 긴 전극을 갖는 스파크 플러그를 적용하였으며 그 결과를 기존의 Base 스파크 플러그 시험 결과와 비교하였다.

• 한국안전학회지
• /
• 제23권2호
• /
• pp.1-6
• /
• 2008

The present study investigates on improvement of inhalation efficiency of hood in ventilation system for elimination of industrial dust. The hood, one of local exhaust ventilation system, has an important function to inhale a pollution source such as harmful dust and industrial waste. In this study, in order to improve the inhalation efficiency of the industrial hood, a new device named "gas-guide-device" was attached to inside of hood. The thermal fluid commercial code "Phoenics ver 3.1" was used to analyze the flow velocity distribution at the hood inlet and around the hood after gas-guide-device was installed. And the flow velocity on each position inside and around the hood was actually measured using the hot wire type anemometer under the same condition as that of numerical analysis. Also, in order to identify the optimum shape of gas-guide-device, numerical analysis and experiments are performed under various conditions and their results are presented. The results of this study revealed that the hood attached with gas-guide-device was higher the inhalation efficiency than that for without one and can be possible to improve the capture velocity of the industrial dust. And the optimum shape of gas-guide-device was identified that the ratio of two sizes of gas-guide-device, X to Y, has 4 to 6 on the basis of the hood size in use and the width (b) of gas-guide-device.

• 한국가스학회지
• /
• 제27권1호
• /
• pp.63-69
• /
• 2023

대한민국은 세계 1위의 반도체 생산 국가임에도 불구하고 산업 보호를 위한 현장의 폐쇄성으로 대부분의 연구가 단순한 물질 위험에 대한 위험성평가로 이루어지고 있다. 산업 안전 측면에서 유해위험물질의 누출 상태를 파악하는 가스 감지기 등의 모니터링 시스템 등을 구축하고 있으나, 누출 시 유해위염 물질을 효과적으로 배기하기 위한 연구는 최근에서야 시작되었다. 인화성 물질이 다량 취급되는 반도체 제조설비(가스박스)는 현재 가스 감지기 및 공기투입구를 막는 방법으로 안전관리를 하고 있는데, 공기투입구가 없으면 박스 내부를 음압으로 관리할 수는 있으나 내부 기류가 원활히 생성되지 않아 인화성 물질 누출 시 단시간 희석이 어렵다. 따라서 본 연구에서는 여러 기준들을 기본으로 하여 가스박스 규모에 따른 덕트 사이즈의 결정, 공기 투입구의 적정크기 연구를 통하여 인화성 누출 시 유해화학물질이 외부로 노출되지 않으면서 배기 성능 요구량을 최소로 할 수 있는 최적 배기 설계를 해보고자 한다.

• 대한임베디드공학회논문지
• /
• 제7권6호
• /
• pp.301-309
• /
• 2012

In this paper, a real-time monitoring system based on WSN is designed and implemented to monitor livestock growth environment information which includes the temperature, humidity and harmful gases such as $CO_{2},\;CO,\;NH_{3},\;H_{2}S$ and so on. The proposed system consists of the wireless sensor nodes, the monitoring management device, the management server and the user interface program based on PC/Smart phone. To verify the performance of the implemented system, gas measurement experiments are performed in laboratory environment by using the designed wireless sensor nodes. And it is able to estimate the concentration of gases. The implemented system is able to monitor the proposed environmental element information through the developed GUI.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.524-529
• /
• 2001

Because of the ozone layer depletion and global wanning, new alternative refrigerants are being developed. Among them, HFC refrigerants are thought promising, but some European countries are arguing that these refrigerants are also harmful to the global wanning. Therefore, natural refrigerants should be considered as an eventual alternative in refrigerators and heat pumps. In the present study, the supercritical gas cooling process are computationally analysed by employing various turbulence models of carbon dioxide in a trans critical refrigeration cycle. The gas cooling process near the critical point experiences a drastic change in thermodynamic and transport properties, thus the heat transfer characteristics would be different from those of two or single phases. Based on the computational results, the correlations to estimate the near-critical heat transfer characteristics will are obtained.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.76-81
• /
• 2006

Modem after-treatment technology has been developed variously in order to decrease exhausted emission in diesel engine. However, it seems very difficult to comply with updated stringent emission standards. Specially, it has been many years that exhaust gas from gasoline automobile rather than from diesel is the major object concerned by Korea and other countries, and it is strongly required on the reduction techniques on harmful NOx and PM among those compositions. Thus, this research focused on the electronic control EGR and the target for this research is heavy-duty turbo-diesel engine with EGR technology(High pressure route and low pressure route system).

• 센서학회지
• /
• 제27권3호
• /
• pp.143-149
• /
• 2018

In this paper, we introduce an edge-spike modulation method for visible light communication (VLC). This method is effective in preventing LED flicker and 120 Hz noise interference in base-band VLC. In the VLC transmitter, edge-spikes are generated by passing the digital data through a simple RC-high pass filter (HPF). The LED modulation of the edge-spikes does not change the average power of the LED light; thus it prevents LED flicker. In the VLC receiver, the 120 Hz noise from other lighting lamps is easily eliminated by RC-HPF, while the edge-spike signal is detected normally. In our experiment, the message of an air-quality sensor was successfully transmitted using edge-spike modulation. This structure is useful in constructing, e.g., wireless gas monitoring sensor systems to warn and prevent harmful gas leakage accidents in buildings using LED light.

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.37-41
• /
• 2012

Usually compound dies are used in clinch washer production. However, in this study, a fine blanking die is designed and manufactured, and clinch washers are produced by the die. Clinch washers are for electric exhaust gas recirculation (EEGR) and they recirculate some of exhaust gas to reduce harmful substances. Fine blanking automation production eliminates difficulties operators face on conventional press.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.1-8
• /
• 2001

It is a present situation that the control on automobile emission is getting more restrictive and also the regulations for emission are changing greatly up to level of those advanced foreign countries. Specially, it has been many years that exhaust gases from gasoline automobile rather than from diesel is the major object concerned by Korea and other countries, and it is strongly required on the reduction techniques on harmful NOx and PM among those compositions. Thus, this research focused on the Exhaust Gas Recirculation (EGR) and the target for this research is heavy-duty turbo-diesel engine with Cooled EGR. Furthermore, this research has been made efforts to accomplish the regulation on emission for heavy duty diesel engine.

• 한국전산유체공학회지
• /
• 제2권2호
• /
• pp.89-96
• /
• 1997

High injection pressure system has been developed as a measure to reduce harmful exhaust gases. In order to understand the effect of pressure on diesel spray injection process, wide range of high injection pressure was tested. The gas phase is modelled by the Eulerian continuum conservation equations of mass, momentum, energy and fuel vapour fraction. The liquid phase is modelled following the discrete droplet model approach in Lagrangian form. The droplet distributions, vapor fractions and gas flows are analyzed in various injection pressure cases. The distributions of spray and vapor increase and the Sauter mean diameter decreases with increasing injection pressure quickly in a low pressure area but slowly in a high pressure area.