• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.36-41
• /
• 2005

PCV(Positive Crankcase Ventilation) valve acts as a flow control valve to get a re-combustion of blow-by gas by having it flow from a crankcase to an inlet manifold suction tube. The blow-by gas of the crankcase should be eliminated or taken properly because it cause corrosion to critical parts, and contributes to increase crankcase pressure that can cause a drop in efficiency. The excessive stress and strain on the PCV valve that remove these harmful gas would be bring the difficult on the flow rate control and failure of the valve. Those condition inevitably induce the accident. Therefore, this study purpose is FEM evaluation of the stresses and deformation in the X3 PCV model according to the change of the differential pressure between inlet and outlet. From results, the maximum equivalent stresses increased linearly according to the increase of the differential pressure at the about 50mm from the inlet position and were under the yield strength of the valve. And the deformations were relatively small regardless of the in-outlet differential pressure variation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.22-28
• /
• 2008

A closed type crankcase ventilation system has been adopted to engines to prevent emission of blow-by gas to atmosphere. In the early closed type crankcase ventilation system, blow-by gas which contains engine lubricating oil is re-circulated into the intake system. The blow-by gas containing oil mist leads to increased harmful emissions and engine problems. To reduce loss of the engine oil, a highly-efficient oil separation device is required. Principle of a cyclone oil separator is to utilize centrifugal force in the separator and, therefore, oil separator designs depend on rotational flow which causes the centrifugal force. In this paper, flow characteristics and oil separation performances for cyclone type designs are calculated with CFD methodology. In the CFD model, oil particle was injected on a inlet surface with Rosin-Rammler distribution and uniform distribution. The major design parameters considered in the analysis model are inlet area, cone length and outlet depth of the oil separator. As results, reducing inlet area and increasing cone length increase oil separation performance. Changes in outlet depth could avoid interference between rotational flow and outlet flow in the cyclone oil separator.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.2
• /
• pp.60-67
• /
• 2011

Ternary B-C-N coatings were deposited on Si(100) wafer substrate from $B_4C$ target by RF magnetron sputtering technique in $Ar+N_2+CH_4$ gas mixture. In this work, the effect of reactant gas ratio, $CH_4/(N_2+CH_4)$ on the composition, kinds and amounts of bonding states comprising B-C-N coatings were investigated using two different bias power sources of continuous and unipolar DCs. In addition, the tribological properties of coatings were studied with the composition and bonding state of coating. It was found that the substrate bias power had an effect on chemical composition, and all of the obtained coatings were nearly amorphous. Main bonding states of coatings were revealed from FTIR analyses to be h-BN, C-C, C-N, and B-C. The amount of C-C bonging mainly increased with increase of the reactant gas ratio. From our studies, both C-C and h-BN bonding states improved the tribological properties but B-C one was found to be harmful on those. The best coating from tribological points of view was found to be $BC_{1.9}N_{2.3}$ composition.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.21-26
• /
• 2011

Emissoin of heavy duty vehicle have much positioned in air pollution although its limited number of vehicles. CNG vehicles are coming to the fore as one of the solution of diesel vehicles. CNG vehicles exhaust smaller emission than diesel vehicles on PM and NOx. In this study, aftertreatment technologies are introduced on vehicles which use CNG and hydrogenmixed fuel. Withmixing hydrogen with CNG, combustion efficiency is enhanced, and harmful emission might be decreased, but methane that is main component of CNG brings green house effect. In order to remove methane and NOx in exhaust gas of CNG engine, methane oxidation catalyst and SCR technologies were respectively analyzed.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.40-46
• /
• 2015

Stoichiometric combustion engine with Three-way catalyst had an advantage that can reduce the harmful emissions effectively. Fuel equivalence ratio controlled from engine is very important because Fuel equivalence ratio with high conversion efficiency was narrow. This study analyzed the conversion efficiency under whole range of operating area for to evaluate the performance of three-way catalyst. In order to identify the Optimum conversion efficiency, the conversion efficiency due to change the control value of fuel equivalence ratio was investigated. The result show that conversion efficiency of emissions(more than 95%) has discovered by means of fuel equivalence ratio control at each test condition. As engine power increases, optimal fuel equivalence ratio tended to increase linearly under operating conditions of similar exhaust gas temperature.

• Journal of the Korean Institute of Gas
• /
• v.7 no.4 s.21
• /
• pp.36-43
• /
• 2003

This paper provides the possibility of the district cooling system by using a LNG cold thermal energy. A liquefied natural gas provides a plenty of cooling source energy during a gasification of a liquefied natural gas. In recent, an ice thermal storage system is used for cooling a building, and a deep water source cooling system has been introduced as a district cooling system in which is used to cool the office towers and other large buildings in old and new downtown. LNG cooling energy refers to the reuse of a large body of naturally cold fluids as a heat sink for process and comfort space cooling as an alternative of conventional, refrigerant based cooling systems. Coincident with significant clean energy and operating cost savings, LNG cold energy cooling system offers radical reductions in air-borne pollutants and the release of environmentally harmful refrigerants in comparison to the conventional air-conditioning system. This study provides useful information on the basic design concepts, environmental considerations and performance related to the application of LNG cold thermal energy.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.91-97
• /
• 2023

Aging construction machinery and vehicles with old diesel engines usually have a long life span, so they continue to emit harmful emissions. Therefore, replacing these older diesel engines with engines that meet the latest emisstion standard is expected to help improve air quality, and engines with propane fuels, which are easily available at construction sites, can be an appropriate alternative. In this study, a propane fueled engine was developed based on a 6.8-liter CNG engine, and technologies such as gas injectors, exhaust gas recirculation (EGR), and enhanced catalysts were applied. As a result, nitrogen oxides achieved half of the emission performance at the Stage-V level, the latest emission standard, while securing diesel engine output and torque in the same class.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.1043-1048
• /
• 1998

The decomposition performance of the Surface induced Plasma Chemical Processing(SPCP) for benzene, toluene, xylene and $NO_2$ were experimentally examined. Discharge exciting frequency range was 5kHz and 10kHz, and low frequency discharge requires high voltage to inject high electric power in gas and to decompose contaminants. The decomposition rate of dioxide nitrogen for 5kHz power in gas and to decompose contaminants. The decomposition rate of dioxide nitrogen for 5kHz power supply is only 85%, but it’s rate for 10kHz power supply is very high, more than 96% when peak voltage is 12kv. Aromatic hydrocarbon vapor of up to 1000ppm is almost throughly decomposed at the flow rate of 1000$\ell$/min or lower rate under the discharge with electric power of several hundred watts. High decomposition rate is shown in every case, that is, for SPCP reactor is necessary to obtain the decomposition rate of more than 80~98%. The decomposition rate of benzene, toluene and xylene were 90~98% and dioxide nitrogen was 45~96%.

• Journal of the Korean Institute of Gas
• /
• v.14 no.3
• /
• pp.35-40
• /
• 2010

This study is to develop of an adsorbent for the removing of human body harmful benzene, toluene, and p-xylene as VOCs. Thus, this study researched the adsorption efficiency of the commercial ACF and the reactivated ACF by KOH/ACF to molar 1: 1. As the results, the effects have shown to enlarge with the increasing of VOCs concentration for adsorptive breakthrough time and breakthrough percentage on each substance. Also, the study have investigated as a similar tendency in case of desorption efficiency for toluene and p-xylene at constant concentration as 125PPM and 0.5$\ell$/min volume flow rate. But in case of benzene, it has been investigated to have rather lower desorption efficiency re-activation ACF than commercial ACF.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.117-120
• /
• 2007

Fuel cells are currently attracting tremendous interest because of their huge potential in stationary applications, in terms of substantiality of our energy use. They also offer environmental advantages, combining significantly higher efficiency with very much lower emission of SOx, NOx, and residual hydrocarbons, and significantly reduced $CO_{2}$ emissions compared to conventional power generation. The molten carbonate fuel cell (MCFC) was introduced from Fuel Cell Energy(FCE), which the one MCFC was operating by LNG and the other was operating by ADG. The ADG contains normally CH4, CO2 and various impurities such as sulfur compounds and siloxanes. Using the ADG as a fuel, MCFC have the potential to provide significant environmental and economic benefits. However, such impurities would be harmful to fuel cells. In this work, a purification process for the ADG was designed and installed in order to utilize the gas as a fuel for MCFC.