• 한국연소학회지
• /
• 제14권3호
• /
• pp.24-28
• /
• 2009

To improve its efficiency, most of the industrial furnace had been used recuperator. However, commonly used metal recuperator is not suitable under condition of temperature higher than $1000^{\circ}C$. The other hand, ceramic recuperator is able to use in high temperature condition. In the present study, the design program based on the basic heat exchanger design theory, and CFD modelling are applied to ceramic recuperator to verify the design results. Using design program to find the optimum design factor on the variation of recuperator condition. The result of this study are as follows : Thinner fin-plate thickness reduces pressure drop and increases heat-transfer rate, However, thin plate or plate with thin thickness(< 5 mm) is difficult to manufacture, due to limited mechanically strength.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.602-605
• /
• 2007

Soybean and rape seed are common feedstocks for biodiesel product ion in USA and Europe, respectively. On the other hand, South Eastern countries like Malaysia and Indonesia have surplus palm crops. However due to substantial amount of saturated fats in palm, the palm biodiesel has poor low temperature properties. To improve the low temperature flow properties as biodiesel, the dependence of the cold filter plugging point (CFPP) on the fatty acid compositions was examined. Two different kinds of biodiesels, palm and soybean biodiesels, were blended with the different volume ratios. And the low temperature flow properties of 0.5%, 1%, and 5% biodiesel in diesel blend fuels was tested. The decrease of CFPP was not observed for BD1 with Palm BD. Also, WDI test didn't exceed in the range of 4oC by the mixing of Palm BD upto 5% in commercial diesels.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.599-602
• /
• 2005

In this research, the characteristics of the strength development and chloride attack resistance on the concrete using high early strength cement by steam curing temperature condition were studied. As a result, It is observed that the early strength(16hr) is increasing and the strength of 28 days is decreasing, according as the rising of the steam curing temperature without the kinds of base cement(OPC and high early strength cement). On the other hand, it is observed that the more the contents of the unit binder(base cement + GGBF) is abundant, the more the steam curing temperature can be reduced in case of the high early strength. Also, the chloride attack resistance is improved according as the amount of GGBF is increased with the kinds of base cement(OPC and high early strength cement).

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2009년 춘계학술발표대회 논문집
• /
• pp.199-203
• /
• 2009

The purpose of this research is to investigate how the indoor temperature has influence on occupants' attention abilities as a basis of productivity. To achieve the purpose, the experiment in chamber was conducted. In the experiment, temperature was controlled according to two levels ($20^{\circ}C$ or $23^{\circ}C$) and other of factors were controlled uniformly. Subjects were exposed to those two different thermal environments. Each participant was asked to mark their answers on the state of attention measurement sheets (FAIR and Trail making test), in two conditions. Total 60 times of experiments were conducted. The main results are as follows. First, subjects showed the better attention abilities in relation to Q score at $20^{\circ}C$. But on the other hand attention abilities in relation to C score were better at $23^{\circ}C$. Second, subjects showed the better attention abilities in relation to concentrate on one task at $20^{\circ}C$.

• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1679-1688
• /
• 1996

Laser flash technique was applied to measure thermal properties of FGM made by a CVD method. System stability and reproducibility of this measuring system were proved and calibrated with glassy carbon used as reference material. Specimens was prepared by cutting FGM diagonally. Measurements were performed for a wide range of temperatures up to 1500K. Relative heat capacity of the FGM specimen was scattered with in $\pm$13% at room temperature and at high temperature above 1200K, and $\pm$3% at medium temperature range. On the other hand, thermal diffusivity data showed excellent reproducibility and stability through the whole temperature range. In conclusion, the multi-target radiometer can be applied to measure the thermal properties of non homogeneous materials like FGM.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.946-951
• /
• 2001

This experimental study is to investigate the intermittent spray characteristics of a pintle nozzle. High speed camera used in this expreiment with 9000fps. The factor, which controls the diesel spray, is the Injection pressure, ambient pressure and ambient temperature. In this paper, experiments were conducted free spray for the ambient pressure(3, 4, 5Mpa), nozzle Injection pressure(10, 14, 18MPa) and ambient temperature(293, 473K). With the higher opening pressure, the spray tip velocity and spray penetration increases while the spray angle decreases, On the other hand, With the higher ambient pressure, the spray angle increase while the spray tip penetration and spray tip velocity decrease. also, With the higher ambient temperature, the spray penetration decrease while the spray angle decrease.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.322-327
• /
• 2000

Natural convection heat transfer in an enclosure with an opening in the right vertical wall and a heat source at the bottom surface is investigated using a holographic interferometric technique. The effects of the opening length, divider length attached to the top wall, and heater temperature on the temperature distribution are examined. The openging length as well as the divider length greatly affects the degree of inflow and outflow of air. With a small opening, the opening doesn't affect much the upward warm air flow resulting in the symmetric temperature distribution. On the other hand, with the increase of the opening length, the inward cold flow moves the upward flow to the left direction. With the increase of the divider length, temperature in the lower region of enclosure becomes higher for the small opening and lower for the large opening.

• Bulletin of the Korean Chemical Society
• /
• 제35권2호
• /
• pp.407-414
• /
• 2014

Polyacrylonitrile (PAN) copolymers with different methyl acrylate (MA) contents were synthesized via solution polymerization and used as precursors for high-performance PAN ultrafine fibrids. The chemical structures of the copolymers were characterized using Fourier-transform infrared spectroscopy and $^{13}C$ nuclear magnetic resonance spectroscopy. Their particle sizes and aspect ratios increased with increasing viscosity, and the degree of crystallinity increased with decreasing concentration of copolymer solution. In contrast, their peak temperature and heat of exotherm increased with decreasing concentration of the copolymer solution. The aromatization indices (AIs) of the fibrids increased with increasing heat-treatment time; however, the AIs decreased when the heat-treatment temperature was higher than the onset temperature of the copolymers. On the other hand, the crystal sizes of the fibrids decreased with increasing concentration of the copolymer solution when the MA content was held constant.

• 반도체디스플레이기술학회지
• /
• 제6권2호
• /
• pp.15-18
• /
• 2007

Effects of $O_2$ flow during deposition on Si crystallization at low substrate temperature were studied. Silicon thin films were prepared on $SiO_2$ substrates in a low-pressure chemical vapor deposition chamber using a mixture of $SiH_4$ and $H_2$. In some cases $O_2$ was intentionally introduced during deposition. Growth of poly silicon was observed at the substrate temperature as low as $480^{\circ}C$ when $O_2$ was flowed during deposition implying that crystallization of Si was enhanced by $O_2$ flow. On the other hand, $O_2$ flow did not show any significant effects at higher substrate temperature, where deposition rate is relatively fast. Enhancement mechanism of Si crystallization by $O_2$ flow was suggested from these results.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1997년도 추계학술대회논문집
• /
• pp.72-96
• /
• 1997

To investigate the difference of sweating reaction on somato types. We measured total sweat rate, locl sweat rate, skin temperature, physiological reactions and psyschological reactions at $25{\pm}1^{\circ}C$ and $25{\pm}1^{\circ}C$ under laboratory conditions. Nine healthy adult females were divided into three somato types (slender(3), normal(3) and obese type(3)). The results were as follows; Total sweat rate was highest in obese type, and then comes normal type and slender type in order. Local sweat rate was highest in infrascapular area, and then breast, the back of the hand, upperarm, ant. leg, and ant. thigh in order in all somato types. Mean skin temperature was highest in slender type, and then normal type and obese type in order. Rectal temperature, blood pressure and pulse rate were highest in boese type. Psychological reactions were appeared 'hot' 'humid' 'sweat' as ambient temperature go up. And somato types make little difference in psychological reactions.