• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.782-784
• /
• 2002

Many compound semiconductors which have high carrier mobility and small band gap have attentive in application of various practical a field. Especially, InSb served for Hall device and magnetic resistor such as magnetic sensor because InSb thin film has high mobility. Many studies on InSb thin film deposition because In and Sb has been very different feature of vapor pressure($10^4$ times) When In and Sb deposited. In this paper studied it In and Sb deposited simultaneously using by method of co-sputtering deposotion. This process, get to effects of manufacture process simplification. After that this paper observed micro structure and electronic behavior of InSb thin film using by co-sputtering.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.113-114
• /
• 2008

Conventional furnace annealing (CFA) for activating Mg-doped p-type GaN films had been performed in pure $N_2$ ambient. All sample activated the same gas ambient. The annealing process change temperature: the first process is performed at $550^{\circ}C$ for 10 min. but, the first process is the same bulk. From second to five process increase activation temperature to change $50^{\circ}C$ and annealing time keeping for 10 min. It is found that the samples characteristic measure hall measurement. Similar results were also evidenced by photoluminescence (PL) measurement.

• 한국생산제조학회지
• /
• 제22권3_1spc호
• /
• pp.558-565
• /
• 2013

This paper describes a whole-body (human body's) motion generation scheme for an android robot that uses motion capture device and a nonlinear constrained optimization method. Because the captured motion data are based on global coordinates and the actors have different heights and different upper-lower body ratios, the captured motion data cannot be used directly for a humanoid robot. In this paper, we suggest a method for obtaining robot joint angles, which allow the resultant robot motion to be as close as possible to the captured human motion data, by applying a nonlinear constrained optimization method. In addition, the results are animated to demonstrate the similarity of the motions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.955-959
• /
• 2004

The effects of conduction band offset on 2 dimensional electron gas (2DEG) in N-InAlAs(AlAsSb)/InGaAs/InAlAs (AlAsSb) metamorphic heterostructures (MMHS) are studied. A combination of the Shubnikov-deHaas oscillations and the Hall measurements is used to investigate the electron transport properties of these structures. The mobility in the second subband is higher than that in the first subband in all heterostructures. This is attributed to the fact that electrons in the first subband we, on average, closer to the interface and are therefore scattered more strongly by ionized impurities. The results suggest that intersubband scattering rate is more dominant in structures with higher conduction band offset whereas alloy scattering is found to be more dominant in the higher band offset system.

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권1호
• /
• pp.32-36
• /
• 2008

An HTS conductor with parallel HTS tapes is essential for a large power HTS device to flow a large current. One of the most important factor for this conductor is a current distribution. Non-uniform current distribution in parallel tapes makes the critical current of the conductor low and the AC losses high. In this paper we proposed a non-contact method which measured each current in parallel tapes by using an array of Hall sensors. A matrix can be derived from this array for calibration. The current distributions of 4 and 6 parallel tapes were measured.

• 한국IT서비스학회지
• /
• 제22권6호
• /
• pp.87-102
• /
• 2023

Existing child car seats do not have a monitoring means for the driver or guardian to effectively recognize the status of whether the seat belt of car seat is fastened and whether the ISOFIX of the car seat is fastened to the inside device of the vehicle. In this paper, we propose a smart car seat system which can monitor in real time, whether the seat belt of a child seated in the car seat is fastened and whether the ISOFIX of the car seat is fastened. The proposed system has been developed with a prototype, in which a Hall sensor, magnet, Bluetooth, and display device are used to detect whether these are fastened and to display the detection results. The prototype system provides the detection results as texts and alarm signal to the display for driver or guardian' smartphone in the car in motion. With functional tests of the prototype system, it was confirmed that the detection functions are properly operated, and the detection results were transmitted to the display device and smartphone via Bluetooth within 0.5 seconds. It is expected that the development system can effectively prevent safety accidents of child car seats.

• 한국자기학회지
• /
• 제16권4호
• /
• pp.216-220
• /
• 2006

10개의 다중 홀(Hall)소자를 이용하여 요골동맥에 놓여진 영구자석의 위치 변화에 따른 전압의 변화를 전기적 신호로 얻었다.전기적 신호는 맥의 파형 신호를 의미하며 이들을 다시 회로의 하드웨어를 통해 신호들을 미분하여 자장의 변화 신호만 얻었다.소프트웨어를 통해 위치 변화에 따른 자장 변화의 크기에 따라 그 형태를 3차원 영상을 얻어 착용형 맥진기로서의 개발 가능성을 보여주었다.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.25-39
• /
• 2020

In this study, an edge device that monitors the injection molding process by measuring the mold vibration(acceleration) signal and the mold surface temperature was developed and evaluated its performance. During injection molding, signals of the injection start, V/P switchover, and packing end sections were obtained through the measurement of the mold vibration and the injection time and packing time were calculated by using the difference between the times of the sections. Then, the mold closed and mold open signals were obtained using a magnetic hall sensor, and cycle time was calculated by using the time difference between the mold closed time each process. As a result of evaluating the performance by comparing the process data monitored by the edge device with the shot data recorded on the injection molding machine, the cycle time, injection time, and packing time showed very small error of 0.70±0.38%, 1.40±1.17%, and 0.69±0.82%, respectively, and the values close to the actual were monitored and the accuracy and reliability of the edge device were confirmed. In addition, it was confirmed that the mold surface temperature measured by the edge device was similar to the actual mold surface temperature.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 동계학술연구발표회 및 스핀트로닉스와 나노물리에관한 국제심포지움
• /
• pp.118-118
• /
• 2007

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2012년도 자성 및 자성재료 국제학술대회
• /
• pp.140-142
• /
• 2012