• Journal of Biosystems Engineering
• /
• 제36권6호
• /
• pp.397-406
• /
• 2011

In this study, surveys on operation status of the 73 tractors with rated power of over 75 kW from six provinces in Korea were performed to obtain basic data required for development and efficient use of the high-power and high-performance tractors. And types of tractors and implements, operation crops, types of operations, annual operation areas, annual operation days, annual operation hours, operation speeds and widths, and problems and improvements in use were investigated. Most (91.7%) of the tractor surveyed were operated for forage and silage crops such as rice straw, whole barley, rye grass, reed canary grass, sudan grass, and the remains were operated for upland crops such as ginseng, sweet potato, potato, chinese cabbage, radish. Main operations of the tractors were cutting, baling, and wrapping for forage crops, plow tillage, rotary tillage, and manure spreading. About half (47.9%) of the tractors were used exclusively for forage crop harvesting such as forage crop cutting, forage baling, and bale wrapping, 24.5% of the tractors were used exclusively for plow or rotary tillage, and 27.4% of the tractors were used for both forage crop harvesting, and plow or rotary tillage. For the tractors with power ranges of 75~83, 89~94, 98~101, 113, 124 kW, average annual operation areas per tractor for plow tillage, rotary tillage, forage crop harvesting (cutting, baling, wrapping), and manure spreading operations were analyzed as 112.6. 144.8, 158.9. 390.0. 215.6 ha, respectively. and total average annual operation area per tractor was 171.3 ha. Average annual operation days per tractor for those operations were analyzed as 24.1, 28.9, 38.3, 55.4, 33.4, respectively, and total average annual operation days per tractor was 33.6. Average annual operation hours per tractor for them were analyzed as 260.0, 321.6, 408.1, 664.8, 413.8, respectively, and total average annual operation hours per tractor for the all tractors was 377.1. Ranges of operation widths of plow tillage, rotary tillage, forage crop cutting, forage baling, bale wrapping, and manure spreading operations were shown as 1.5~2.6, 2.3~3.0, 1.8~3.2, 1.8~2.0, 1.8~2.3, 3.1~6.6 m, respectively. Ranges of operation speed of plow tillage, rotary tillage, forage crop cutting, forage baling, bale wrapping, and manure spreading were shown as 6~9, 4~11, 9~16, 8~15, 8~17, 12~16 km/h, respectively.

• 한국잠사곤충학회지
• /
• 제13권2호
• /
• pp.81-94
• /
• 1971

적기의 조상중간벌채시기 및 잔조에서의 적엽정도가 재발아와 선단고사, 수량 및 아고병등의 발생에 미치는 영향을 조사한바, 다음과 같은 결과를 얻었다. 1. 조상의 중간벌채시기가 늦어지는데 따라서 재발아 조수가 감소하는 것이며 또 잔조에 잔엽을 많이 할수록 재발아조수가 적어질뿐만아니라 재발아엽수도 적어지는데 잔엽은 잔조의 상부에 하여야만 재발아억제의 효과가 있는 것이니 실용적으로는 3∼5 엽정도의 잔엽이 유리할 것 같다. 3∼5엽정도 잔엽을 하고 9월 20일 이후벌채를 하면 재발아조수가 격감한다. 2. 벌채후의 잔조에서 전적엽을 하면 지조의 선단고사비율이 매우 높고 상반부적엽구도 그외의 다른구들보다 약간 많은 것 같으며 벌채시기에 따라서는 전적엽구를 제외한 다른구에서는 별로 차가 없는 것 같지만 전적엽구만은 9월 15일 벌채구가 특히 높으니 이것은 전적엽으로 인한 지조의 불윤실과 이때의 온도조건이 아지병균의 기생에 호적하였다는 것이 그 원인인 것 같다. 3. 수량과의 관계를 보면 추잠기는 벌채시기에 따라서는 별로 차가 없지만 잔조에시의 적엽양이 많아질수록 전수량이 많아진다. 춘잠기수량은 무적엽구와 전적엽구는 벌채시기의 여하에 불구하고 가장 적으며 무적엽구를 제외한 그 외의 각구에서는 9월 15일과 9월 20일 벌채구가 수량이 발은 반면에 이보다 이르거나 늦은 경우에는 수량이 적어진다. 또 적엽각구는 9월 15일과 9월 20일 벌채구를 제외하고는 대체로 무적엽구보다 적으니 추기에 있어서의 적엽이 익춘기의 수량에 상당한 영향을 미치고 있다. 춘추합계수량에 있어서는 무적엽구와 전적엽구보다 그 외의 각구가 수량이 많으며 그 중에서도 9월 15일과 9월 20일 벌채구가 특히 많고 잔엽정도에 따르는 차는 별로 없는 것 같다. 이것을 종합해 볼때에 연간수량이 가장 많은 것은 9월 15일∼20일경에 중간벌채수확을 한후 그잔조에 3∼5 엽잔엽을 하는 방법이며 9월 5일∼10일 벌채구도 무적엽구나 그 이후의 벌채구와 별로 차가 없다. 4. 잔조에 발생하는 병은 아고병 가장 심하고 맛사리아병과 동고병도 약간 발생하였으며 아고병은 전적엽구에 가장 심하게 발생하였고 시기적으로는 9월 15일구에서 지수 92.9, 9월 20 일구에서는 지수 100으로 가장 심하게 발생하였으며 상반부적엽구에서도 상당히 발생하였고 무적엽구는 거의 발생하지 않았다. 5. 재발아비율 및 평균재발아엽수와 익춘잠기 수량과의 사이에는 각각 상관계수 r=-0.42, r=-0.27로서 부외 상관을 가지고 있으나 깊은 상관관계는 없으며 선단고사비율 및 아고병발생비율과 익춘잠기수량과의 사이에는 거의 상관이 없다. 아고병발생비율과 선단고사비율과의 사이에는 상관계수 r=＋0.8로서 깊은 정의 상관이 있다.

• Journal of Chest Surgery
• /
• 제15권3호
• /
• pp.366-369
• /
• 1982

Single coronary artery is rare congenital anomaly with incidence about 0.04%. Above half of single coronary artery is symptomless, and about 41% of cases are associated with another congenital cardiac anomalies . Single coronary artery is sometimes important for cardiac operation to avoid fatal result from cutting of coronary artery during the right ventriculotomy. Among the associated anomaly of the single coronary artery, coronary arteriovenous fistula is very rare. We experienced congenital single coronary artery with coronary arteriovenous fistula drained into the right ventricle, and so we report this case with literatures.

• 전자통신동향분석
• /
• 제32권6호
• /
• pp.57-65
• /
• 2017

Neural network based AI computing is a promising technology that reflects the recognition and decision operation of human beings. Early AI computing processors were composed of GPUs and CPUs; however, the dramatic increment of a floating point operation requires an energy efficient AI processor with a highly parallelized architecture. In this paper, we analyze the trends in processor architectures for AI computing. Some architectures are still composed using GPUs. However, they reduce the size of each processing unit by allowing a half precision operation, and raise the processing unit density. Other architectures concentrate on matrix multiplication, and require the construction of dedicated hardware for a fast vector operation. Finally, we propose our own inAB processor architecture and introduce domestic cutting-edge processor design capabilities.

• 대한치과보철학회지
• /
• 제13권1호
• /
• pp.23-26
• /
• 1975

The purpose of this study was to measure the retentive force of various kinds of dental cement. Cross-cutting the half of the occlusal surface, pinholes were prepared on the dentin with No. 557 carbide bur. No. 557 steel burs were cemented in the pinholes and retentive force was measured by removing the burs with Instron testing machine. The Instron testing machine was operated at a rate of 0.2 cm per minute. The following results were obtained : 1. The retentive force of zinc phosphate cement(A), reinforced zinc oxide and eugenol cement and polycarboxylate cement were similar to each other, but that of zinc phosphate cement (A) was the highest of all. 2. The retentive force of zinc phosphate cement (B) was the lowest of all.

• 한국조경학회지
• /
• 제25권2호
• /
• pp.9-19
• /
• 1997

These studies were carried out to investigate seed propagation method and conducted using stem cuttings of Styrax japonicus for using as a woody landscape plant. The results are obtained as follows. After the H\sub2\SO\sub 4\ and GA\sub 3\ treatment to the seeds of Styrax japonicus, three months of warm treatment followed by cold stratification for four months increased seed germination rate. The rooting rate of Styrax japonicus was increased by the treatment with concentrated IBA, especially highest at 7,000ppm. Rooting percentages were highest for cuttings taken on July 15, 1995. Therefore, the most effective method for rooting of Styrax japonicus was treatment with 7,000ppm IBA on July 15 cuttings, which showed rooting rate of over 90%. Half-leaf-remained cuttings were more effective than those with two leaves on rooting of Styrax japonicus. Dipping for 10 seconds in IBA solution resulted in rooting rate of over 70%. The longer the treatment time the worse the rooting.

• 한국기계가공학회지
• /
• 제20권9호
• /
• pp.48-56
• /
• 2021

Tungsten carbide (WC) circular saws have been widely used to cut plywood. Recently, expensive polycrystalline diamond (PCD) were adopted to extend the tool life of circular saws. This study developed a PCD-WC combination circular saw and compared its performance with that of existing WC and PCD saws. Flank wear of WC saw blades and edge chipping of rectangular PCD was observed during the experiments. The PCD-WC saw replaced half of the chamfered teeth with PCD and applied tough WC for all rectangular teeth. In the experiments, edge chipping was not observed in rectangular WC teeth and the flank wear of chamfered teeth was decreased compared with that of conventional circular saws.

• Composites Research
• /
• 제34권2호
• /
• pp.96-100
• /
• 2021

The lightweight industry continuously demands reliable near-net-shape fabrication where the preform just out-of-machine is close to the final shape. In this study, different half-finished preforms are made π-beams. Then the preforms are unfolded to make a 3D shape with integrated structure of fibers, providing easier handling in the further processing of composites. Several 3D textile preforms are made using weaving technique and are examined after resin infusion for mechanical properties such as inter-laminar shear strength, compressive strength and tensile strength. Considering that the time and labor are important parameters in modern production, 3D weaving technique reduces the manufacturing steps and therefore the costs, such as hand-lay up of textile layers, cutting, and converting into preform shape. Hence this 3D weaving technique offers many possibilities for new applications with efficient composite production.

• 한국기계가공학회지
• /
• 제21권5호
• /
• pp.77-83
• /
• 2022

A high-hardness tool material is required to reduce extreme abrasive wear when drilling carbon fiber reinforced plastic (CFRP). Single-crystal diamond is the hardest material in the world, but it is very expensive to be used as a cutting tool. Polycrystalline diamond (PCD) is a diamond grit fused at a high temperature and pressure, and diamond-like carbon (DLC) is an amorphous carbon with high hardness. This study compares DLC coatings and PCD inserts to conventional TiAlN-coated tungsten carbide drills. In fiberglass and carbon fiber reinforced polymer drilling, the tool wear of DLC-coated carbide was approximately half that of TiAlN-coated tools, and slight tool wear occurred in the case of PCD insert end drills.

• 대한본초학회지
• /
• 제31권3호
• /
• pp.37-41
• /
• 2016

Objectives : The purpose of this study is to assume the size of sliced piece, daily dose and extracting Method of Rhubarb in Treatise on Cold Damage Diseases.Methods : I contrast results of recent studies with assuming results based on original text of Treatise on Cold Damage Diseases.Results : Daily dose was 6, 4 or 2 Ryang in case of cutting Rhubarb in bean-size. These prescriptions were decocted with water or sinked in boiled water. Another daily doses were large baduk-piece size 6 units and baduk-piece size 6 units in case of cutting Rhubarb in size bigger than bean. The former was used in adding to the Jisilchijasi-tang in case of constipation, the latter was used in Sihogayonggolmoryeo-tang and Jeodang-tang. The size of large baduk-piece was 2.32 cm in width, 4.64 cm in length, 4.3 g in weight, and the length and weight of baduk-piece was half of that was. Two sizes of Rhubarbs were sunk in water for 12 hours. After decocting the other ingredients, mixed Rhubarb extraction and Rhubarb, and then boiled it for 1 minute.Conclusions : From this study, daily dose of Rhubarb was 6, 4 or 2 Ryang and the 6 pieces of large baduk-piece or baduk-piece are respectively 4 or 2 Ryang. The extracting methods was decocting, sinking in boiled water for short time, sinking in water for long time and then mixing these with other decocted solution.