• 한국해양환경ㆍ에너지학회지
• /
• 제17권3호
• /
• pp.174-181
• /
• 2014

선형발전기가 연결된 부이의 수직운동에 대한 시간영역 해석을 수행하여 얻은 시계열 자료를 가지고 선형발전기를 설계하고 전기에너지 출력특성 및 효율에 대해 살펴보았다. 1차 변환장치로 원통형 부이를 선택하였고, 2차 변환장치로 양측식 할박(Halbach) 배열 영구자석 가동자와 철심형 슬롯리스(Slotless) 고정자로 구성된 선형발전기를 사용하였다. 시간영역에서 부이의 수직운동 속도와 파랑하중을 입력자료로 직선형 영구자석 발전기가 설계되었고, 설계된 발전기는 규칙파 조건에서 유한요소 해석법을 적용하여 발전특성해석을 수행함으로써, 그 타당성이 입증되었다. 또한 불규칙파 조건에서 합리적이고 빠른 해석을 위해, 등가회로법을 적용하여 발전특성 해석을 수행하였는데, 그 결과 역시 매우 타당함을 확인하였다.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.438-444
• /
• 2013

This paper presents the replication of a desired vibration response by iterative learning control (ILC) system for a vibration motion replication actuator. The vibration motion replication actuator has parameter uncertainties including system nonlinearity and joint nonlinearity. Vehicle manufacturers worldwide are increasingly relying on road simulation facilities that put simulated loads and stresses on vehicles and subassemblies in order to reduce development time. Road simulation algorithm is the key point of developing road simulation system. With the rapid progress of digital signal processing technology, more complex control algorithms including iterative learning control can be utilized. In this paper, ILC algorithm was utilized to produce simultaneously the six channels of desired responses using the Stewart platform composed of six linear electro-magnetic actuators with Halbach magnet array. The convergence rate and accuracy showed reasonable results to meet the requirement. It shows that the algorithm is acceptable to replicate multi-channel vibration responses.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권3호
• /
• pp.60-64
• /
• 2012

In this paper, an investigation of a room temperature active magnetic regenerative refrigerator is carried out. Experimental apparatus includes two active magnetic regenerators containing 186 g of Gd spheres. Four E-type thermocouples are installed inside the Active magnetic regenerator(AMR) to observe the instantaneous temperature variation of AMR. Both warm and cold heat exchangers are designed for large temperature span. The cold heat exchanger, which separates the two AMRs, employs a copper tube with length of 80 mm and diameter of 6.35 mm. In order to minimize dead volume between the warm heat exchanger and AMRs, the warm heat exchangers are located close to the AMRs. The deionized water is used as a heat transfer fluid, and maximum 1.4 T magnetic field is supplied by Halbach array of permanent magnets. The AMR plate, which contains the warm and the cold heat exchangers and the AMRs, has reciprocating motion using a linear actuator and each AMR is alternatively magnetized and demagnetized by a Halbach array of permanent magnet. Since the gap of the Halbach array of permanent magnets is 25 mm and two warm heat exchangers have the motion through it, a compact printed circuit heat exchanger (PCHE) is used as a warm heat exchanger. A maximum no-load temperature span of 26.8 K and a maximum cooling power of 33 W are obtained from the fabricated Active Magnetic Regenerative Refrigerator (AMRR).

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권8호
• /
• pp.400-407
• /
• 1999

This paper treated the design, manufacture and the performance characteristics under each mode of high speed motor/generator for an electro-mechanical battery(EMB). This machine is employed as an integral part of a flywheel energy storage system(FESS), i.e., a modular flywheel system to be used as a device for storing electrical or mechanical energy. In this machine, the magnetic field system is constructed by using special magnet array, dipole Halbach array with 16 permanent magnet segments and the armature is composed of a plastic bobbin and multi-phase windings with Litz wire. The magnet array produces a highly uniform dipole field without back iron. The motor/generator is 3-phase machine in which the dipole Halbach array surrounding the winding is rotating. Since there are no iron laminations, this field system offers some unique advantages for the simplicity of the design and the theoretical prediction of characteristics of a high speed electric machine. This paper describes the results obtained when EMB system was tested in the laboratory.

• 대한기계학회논문집A
• /
• 제35권4호
• /
• pp.353-358
• /
• 2011

본 논문에서는 환형 영구자석을 이용한 스러스트 베어링의 최적설계에 대하여 기술하였다. 영구자석형 스러스트 베어링은 두 조의 환형 영구자석으로 이루어지며, 한 조의 영구자석이 다른 한 조의 영구자석 내부에위치한다. 영구자석간의 축방향 변위 (엇갈림)에 의해 축방향 힘이 발생하고 이를 통해 스러스트 베어링 역할을 하게 된다. 최소한의 영구자석으로 베어링 부하용량을 만족하는 베어링 설계 파라미터를 구하기 위해 본 논문에서는 등가전류판 방법을 이용하여 해석적 설계식을 유도하고, 적절한 제한 조건을 설정하여 최적 설계를 수행하였다. 최적 설계 결과는 3 차원 유한요소해석을 통해 검증하였다. 본 논문에서 고려한 축방향 배열과 Halbach 배열의 스러스트 베어링 중 Halbach 배열이 축방향 배열에 비해 동일한 부피의 영구자석으로 더 큰 부하용량을 얻을 수 있음을 확인하였다. 등가전류판 방법의 유효성을 3 차원 유한요소해석을 통해 검증하였고, 축방향 배열보다Halbach 배열이 등가전류판 방법의 가정에 좀 더 민감하게 영향을 받는 것을 알 수 있었다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.180.2-180.2
• /
• 2008

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.222.2-222.2
• /
• 2008

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권4호
• /
• pp.146-150
• /
• 2001

Comparison on the performances between the Halbach array type permanent magnet linear synchronous motor (HA-PMLSM) and the convensional array type permanent magnet linear synchronous motor (CA-PMLSM) was made with finite element analysis (FEA) and experiment. The HA-PMLSM is seen to be superior to the CA-PMLSM. Optimum ratio of magnet length to slot pitch of the HA-PMLSM which reduces the detent force was determined. Also, Comparison of forces of the HA-PMLSM and the CA-PMLSM with minimum detent force is presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.641-643
• /
• 2002

Synchronous generator needs slip-ring and brush for supplying current to rotor with external source. but slip-ring and brush have some problems to supply DC power to field winding with friction and high power loss due to brush voltage drop at high field current. Thus synchronous generator have been designed to brushless machine. Brushless synchronous machines of using permanent halbach array can composed without back core and coreloss. In this paper, analyse on the characteristics of external rotor type permenant magnet brushless with halbach array.

• 전기학회논문지
• /
• 제59권12호
• /
• pp.2319-2323
• /
• 2010

The existing contact-type bearings using rolling or sliding require continuous maintenance due to abrasion caused by friction and are not suitable for high-speed rotation and slimming. A magnetic bearing without contact can overcome such problems but the performance depends on the allocation of magnets and the structure of bearings. This paper proposes a method designing parameters of a passive magnetic bearing to improve levitation force. The proposed method employs Halbach array as the allocation of magnets, uses particle swam optimization to determine the structure of bearings. The numerical experiment shows that the levitation force is improved by the proposed method compared with the existing one using finite element analysis.