• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.1
• /
• pp.27-34
• /
• 2001

The effects of pre-heat treatment(Q/T) on microstructure and hardness of STD11 and STD61 tool steel nitrided by micro-pulse plasma were investigated. The quenching temperature for obtaining matrix hardness of STD11 and STD61 steel on range of HRC 50 to HRC 60 desired for machine parts is about $1070^{\circ}C$ and $1020^{\circ}C$ respectively. The hardness of STD11 and STD61 quenched at the temperature was HRC 63 and HRC 56 respectively. The nitrided case depth of STD11 and STD61 nitrided at $550^{\circ}C$ for 5 hours was independent of pre-heat treatment condition and the depth was approximately $100{\mu}m$. However, hardness and compactness of nitrided layer on Q/T treated specimen were higher than the annealed specimen. The case depth increased linearly with the increase of nitriding temperature, however, the hardness of nitrided layer decreased with the increase of temperature. Phase mixture of ${\gamma}-Fe_4N$ and ${\varepsilon}-Fe_{2-3}N$ was detected by XRD analysis in the nitrided layer formed at the optimum nitriding condition. The optimum nitriding temperature was approximately $490^{\circ}C$ which was $10^{\circ}C$ lower than the tempering temperature for preventing softening behavior of STD11 and STD61 matrix during nitriding process and the surface hardness of nitrided layer obtained by optimum pre-heat treatment condition was about Hv1400.

• Korean Journal of Soil Science and Fertilizer
• /
• v.47 no.2
• /
• pp.85-91
• /
• 2014

Ground-based polarimetric scatterometers have been effective tools to monitor the growth of crop with multi-polarization and frequencies and various incident angles. An important advantage of these systems that can be exploited is temporal observation of a specific crop target. Polarimetric backscatter data at L-, C- and X-bands were acquired every 10 minutes. We analyzed the relationships between L-, C- and X-band signatures, biophysical measurements over the whole corn growth period. The Vertical transmit and Vertical receive polarization (VV) backscattering coefficients for all bands were greater than those of the Horizontal transmit and Horizontal receive polarization (HH) until early-July, and then thereafter HH-polarization was greater than VV-polarization or Horizontal transmit and Vertical receive polarization (HV) until the harvesting stage (Day Of Year, DOY 240). The results of correlation analysis between the backscattering coefficients for all bands and corn growth data showed that L-band HH-polarization (L-HH) was the most suited for monitoring the fresh weight ($r=0.95^{***}$), dry weight ($r=0.95^{***}$), leaf area index ($r=0.86^{**}$), and vegetation water content ($r=0.93^{***}$). Retrieval equations were developed for estimating corn growth parameters using L-HH. The results indicated that L-HH could be used for estimating the vegetation biophysical parameters considered here with high accuracy. Those results can be useful in determining frequency and polarization of satellite Synthetic Aperture Radar stem and in designing a future ground-based microwave system for a long-term monitoring of corn.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4365-4370
• /
• 2012

AZ31 Mg alloy were coated by Macro Arc Oxidation(MAO) with 3 types of electrolyte and various coating times at 4A/$cm^2$. The Surface morphology of coatings became lager pores and surface crack initiated as the coating time increased. The thickness and micro-hardness of coatings increased as the coating time increased. also. The phase of coatings on AZ31 alloy consisted of MgO, $Mg_2SiO_4$ and $MgAl_2O_4$ oxides. The salt spray corrosion resistance of coated AZ31 alloys revealed excellent corrosion resistance in 5% NaCl solution for 168hr.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.5
• /
• pp.147-154
• /
• 2015

In this paper, we employed a model which defines the sensitivity according to the background luminance, so called JND (Just Noticeable Difference), and applied to the video coding. The proposed method finds out the maximum possible quantization parameter for the current unit based on the threshold of JND model and reduce the bitrate with similar perceptual quality. It selects the higher quantization parameter and reduce the bitrate when the reconstructed signal which is coded with higher quantization parameter is in a range of allowance based on the JND threshold, i.e. the signal has the similar perceptual quality compared to that is coded with the initial quantization parameter. The proposed algorithm was implemented on HM16.0, which is a reference software of the latest video coding standard HEVC (High Efficiency Video Coding) and the coding performance was evaluated. Compared to HM16.0, the proposed algorithm achieved maximum 20.21% and 6.18% of average bitrate reduction with the similar perceptual quality.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.126-135
• /
• 1997

$H_2/O_2$ 비에 따른 Hybrid HVOF 용사된 $Cr_3C_2$-7wt%(NiCr) 용사층의 특성 및 산화거동 This study was performed to investigate the influence of fuel/oxygen ratio (F/O=3.2, 3.0, 2.8) on the characteristics and the oxidation behavior of the hybrid-HVOF sprayed $Cr_3C_2$-7wt%NiCr coatings. Decomposition and the oxidation of the $Cr_3C_2$was occured during spraying. The degree of transformation from $Cr_3C_2$to $Cr_7C_3$ was increased with decreasing the F/O ratio. The microstructural differences of the as sprayed coating with F/O ratio can not be distinguished, However, large pores were diminished and then the coatings became dense by heat treatment. Microhardness of the as-sprayed specimen which sprayed with F/O=3.0 condition was hightest ($Hv_{300}$=1140) and the hardness was increased to 1500 after heat treatment at $600^{\circ}C$ for 50hrs in air. It was supposed that hardness was increased due to the formation of $Cr_2O_3$ within $Cr_3C_2$/$Cr_7C_3$matrix and the densification of coating layer during heat treatment. Apparent activation energy for oxidation was varied from 21.2 kcal$mol^{-1}K^{-1}$ to 23.8 kcal$mol^{-1}K^{-1}$ with respect to the F/O ratio. The surface morphology was changed to porous and oxide chusters were grown after oxidation $1000^{\circ}C$ for 50 hours by the aggressive evolution of gas phase ($CrO_3$ and$CO_2$). The oxide cluster was composed of Ni and Cr.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.5
• /
• pp.87-93
• /
• 2008

The objective of this paper is the investigation of the statistical properties of Vickers hardness (HV) of friction welded parts in nickel based super resisting steel, alloy 718 steel. First, we examine the statistical properties on the case of as-welded parts. Several Virkers indentations were made under same nominal conditions. This was repeated for three different applied loads, 100, 200 and 300g with a duration time, 10 second. The arithmetic mean of Vickers hardness in base metal (BM) materials is larger than that of HAZ in all applied loads. The measure of dispersion, that is, the coefficient of variation (COV) for BM and HAZ is decreased by increasing with the applied load. The distribution of Vickers hardness was not found to be symmetric type. The probability distribution of Vickers hardness was well followed Weibull distribution. The shape parameter and the scale parameter (characteristic hardness) are increased by increasing with the applied load, as both BM and HAZ.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.334-344
• /
• 1998

Yew coating pmccss t.o form a surface layer ol CrN phasc on mild steel (A81 1020!, AlSI Hi3, 1Cr-0.5Mo steel (ASTM A213 and Nickrl-base superalloy (Inconel 718) was developed. Surlaces of various alloys t,n.ateii by chromizing for the formation ol Cr diffusion layer was subsequently trcaled by plasma nitriding in order t.o form the hard CrS coating layer on the surfaces. This duplex plasma surface tri-atments of chromizing and plasma nitriding have induced a lormation of a duplex-lrcated surfacr hyer of approximat~ls 70-80 $\mu\textrm{m}$thickncss with a iargcly improved microiiardnrss up to approxiniateW 1500Hv(50gf). The main cause for the lage improvment in the surface hardncss is altribilted to [.he fact that CrN and $Fe_xN$ phases are created successfully by ccliromizins and plasma nilriding treatment. High tenipera1,urc wear resislance of the duplex-treated mild steel and HI3 steels at $600^{\circ}C$ was examined. Comparing the duplex-treated specimens with the specimens treated only by chromizing, the rcsults shovmi that, thc wear volume of the duplex-treated mild skcl and 1113 stcel aSt.er a wear test, at $600^{\circ}C$ were reduced hy a Iactor of 8 and 3, respectively. Characteristics of the CrS phase by duplrx treatment were compared with $CrN_x$,/TEX> film by ion plating and the wear behaviors of CrN film lormed by two different nroccsses arc nea.riy identical.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.8
• /
• pp.958-968
• /
• 2003

The purpose of this study was to clarify the different mechanical properties of fabrics among the theme groups classified by fashion fabric trend. This study can be useful for fabric marketers and planners to design new products. In order to carry out this study, the fabric samples of representative theme for‘2002/03 F/W fashion fabric trend were collected from a fashion company and were measured to analyze the mechanical properties, hand value(H.V) and total hand value(T.H.V) by KES-FB System. The results were as follows. 1. The theme-A of‘Luxury, Elegance’was consisted of wool, rayon and PET and had a lower B, 2HB of bending properties and a lower G and 2HG5 of shear properties. The theme-B of‘Technical, Functional’was consisted of synthetic fibers such as PET, PA, PU and elastic fiber and had a higher MIU and a lower MMD, SMD of surface properties. The theme-C of‘Vintage, Aged’was consisted of mostly cotton and had the highest B and 2HB. The theme-D of‘Fancy, Airy’was consisted of mostly woolen wool, polyacryl and polyamide and had a high MMD and SMD of surface properties and a high LC and RC of compression properties. 2. As the results of analyzing H.V and T.H.V through KES-FB system, the theme-A showed a higher Smoothness and lower Stiffness. The theme-B had a lower Smoothness, Fullness, Soft feeling and T.H.V and the theme-C had the highest Stiffness. The theme-D showed the highest Fullness and Soft Feeling but the lowest Stiffness.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.9_10
• /
• pp.1453-1464
• /
• 2007

The purpose of this study is to examine the hand of spring/fall fabrics for 'Saenghwal Hanbok' on subjective hand, objective hand and the preference. In this study, 28 varieties of spring/fall fabrics such as cotton fabrics, synthetic fabrics, blended fabrics and a silk fabric for 'Saenghwal Hanbok' are used. To evaluate the subjective hand of fabrics, the holistic touch and preferences, 33 seven ranks' segmentic differential scale questions are developed with adjective pairs and are gathered by surveying experts on clothes. The mechanical properties, HV and THV of them are measured and calculated by KES-FB system. Through subjective hand, items could be classified into six hand expressions: 'bulky/extensibility', 'stiffness', 'feeling of weight', 'surface property', 'drapability' and 'moisture property'. Through mechanical properties, the results indicated that the character of cotton fabrics are slight flexible, tough, rough, uneven, a bit heavy, thick and low resilience on tensile and compression, and then those of synthetic fabrics, blended fabrics and a silk fabric are thin and light, smooth, flat and bulkless. In correlation on subjective evaluations and the preference for 'Saenghwal Hanbok', cotton fabrics mainly depend on 'surface property' and 'moisture property' and then synthetic fabrics, blended fabrics and a silk depend on 'bulky/extensibility' and 'surface property' In correlation on objective hand and the preference for 'Saenghwal Hanbok'. people aren't satisfied with low resilience. high stiffness and low drape.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.559-569
• /
• 2010

The liquid-phase sintering method was used to prepare a glass lens forming core composed of SiC-$Al_2O_3-Y_2O_3$. Spark plasma sintering was used to obtain dense sintered bodies. The sintering characteristics of different SiC sources and compositions of additives were studied. Results revealed that, owing to its initial larger surface area, $\alpha$-SiC offers sinterability that is superior to that of $\beta$-SiC. A maximum density of $3.32\;g/cm^3$ (theoretical density [TD] of 99.7%) was obtained in $\alpha$-SiC-10 wt% ($6Al_2O_3-4Y_2O_3$) sintered at $1850^{\circ}C$ without high-energy ball milling. The maximum hardness and compression stress of the sintered body reached 2870 Hv and 1110 MPa, respectively. The optimum ultra-precision machining parameters were a grinding speed of 1243 m/min, work spindle rotation rate of 100 rpm, feed rate of 0.5 mm/min, and depth of cut of $0.2\;{\mu}m$. The surface roughnesses of the thus prepared final products were Ra = 4.3 nm and Rt = 55.3 nm for the aspheric lens forming core and Ra = 4.4 nm and Rt = 41.9 for the spherical lens forming core. These values were found to be sufficiently low, and the cores showed good compatibility between SiC and the diamond-like carbon (DLC) coating material. Thus, these glass lens forming cores have great potential for application in the lens industry.