• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.3-15
• /
• 1996

The formation of a thicker hard alloyed layer have been investigated on the surface of aluminum cast alloy (AC2B) by PTA overlaying process with Cr, Cu and Ni motel powders under the condition of overlaying current 125-200A. overlaying speed 150 mm/min and different powder feeding rate 5-20 g/min. In addition the characteristics of hardening and wear resistance of alloyed layer here been examined in relation to the microstructure of alloyed layer. Main results obtained were summarized as follows: 1) There was an optimum overlaying condition to get a good alloyed layer with smooth surface. This good layer became easy to be formed as increasing overlaying current and decreasing powder feeding rate under a constant overlaying speed. 2) Cu powder was the most superior one in metal powders used due to a wide optimum overlaying condition range, uniform hardness distribution of Hv250-350, good oar resistance and freedom from cracking in alloyed layer with fine hyper-eutectic structure. 3) On the contrary, irregular hardness distribution was usually obtained in Cr ar Ni alloyed layers of which hardness was increased as Cr or Ni contents and reached to maximum hardness of about Hv400-850 at about 60wt%cr or 40wt%Ni in alloyed layer. 4) Cracking occurred in Cr or Ni alloyed layers with higher hardness than Hv250-300 at mere than 20-25wt% of Cr or Ni contents in alloyed layer. Porosity was observed in all alloyed layers but decreased by usage of spherical powder with smooth surface.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.7-11
• /
• 2014

The Polarization and Depolarization Current (PDC) measurement is an efficient and effective diagnostic technique based on time domain measurement, for evaluating the high voltage insulation condition. This paper presents a review and comparison results from several published papers on the application of the PDC method to finding the conductivity and moisture content of various types of insulators. For solid insulation, the study was focused on cable insulation, electric machine stator insulation, and paper insulator in transformer insulation with different conditions. For liquid insulation, the review and comparison was done on biodegradable and mineral transformer oils, with fresh oil condition, and aged condition. The results from previous researchers tests were complied, analyzed and discussed, to evaluate the application of the PDC method to monitor the conductivity and moisture of HV equipment insulation systems. From the review results, the PDC technique successfully gives an indication of the conductivity and moisture level of high voltage insulation.

• Journal of Korea Foundry Society
• /
• v.19 no.5
• /
• pp.403-409
• /
• 1999

Mg-Zn-Zr ternary alloys containing 6wt% Zn and (0, 0.4, 0.6)wt% Zr, which is added for grain refinement, can be cast into complex shape by squeeze casting. The influence of Zn and Zr as additional elements on microstructure and mechanical characteristics is investigated by OM, SEM, WDX, XRD and microvickers hardness measurement. The microstructure of Mg-Zn-Zr alloys consists of primary ${\alpha}-Mg$ and MgZn eutectic compound between dendrites. The grain size is decreased from $136{\mu}m$ to $97\;{\mu}m$ by Zr addition, resulting in that the hardness is increased from 42Hv to 59Hv. Furthermore, the grain size is changed to $83{\beta}$ and the hardness is increased to 65Hv by additional infiltration pressure. These results indicate that the Zr addition and additional infiltration pressure are effective for grain refinement acting as an important factor to increase the hardness. The increment in hardness by the Zr addition is slightly larger than that by the additional infiltration pressure.

• Korean Journal of Materials Research
• /
• v.21 no.7
• /
• pp.364-370
• /
• 2011

Currently, there are two main issues regarding the development of core technologies in the automotive industry: the development of environmentally friendly vehicles and securing a high level of safety in the event of an accident. As part of the efforts to address these issues, research into alternative materials and new car body manufacturing and assembly technologies is necessary, and this has been carried out mainly by the automotive industries. Large press molds for producing car body parts are made of cast iron. With the increase of automobile production and various changes of design, the press forming process of car body parts has become more difficult. In the case of large press molds, high hardness and abrasive resistance are needed. To overcome these problems, we attempted to develop a combined heat treatment process consisting of local laser heat treatment followed by plasma nitriding, and evaluated the characteristics of the proposed heat treatment method. From the results of the experiments, it has been shown that the maximum surface hardness is 864 Hv by the laser heat treatment, 953 Hv by the plasma nitriding, and 1,094 Hv by the combined heat treatment. It is anticipated that the suggested combined heat treatment can be used to evaluate the durability of press mold.

• Korean Journal of Remote Sensing
• /
• v.24 no.5
• /
• pp.445-452
• /
• 2008

Preliminary results are reported on ship detection using coherence images computed from cross-correlating images of multi-look-processed dual-polarization data (HH and HV) of ENVISAT ASAR. The traditional techniques of ship detection by radars such as CFAR (Constant False Alarm Rate) rely on the amplitude data, and therefore the detection tends to become difficult when the amplitudes of ships images are at similar level as the mean amplitude of surrounding sea clutter. The proposed method utilizes the property that the multi-look images of ships are correlated with each other. Because the inter-look images of sea surface are covered by uncorrelated speckle, cross-correlation of multi-look images yields the different degrees of coherence between the images and water. In this paper, the polarimetric information of ships, land and intertidal zone are first compared based on the cross-correlation between HH and HV images, In the next step, we examine the technique when the dual-polarization data are split into two multi-look images, It was shown that the inter-look cross-correlation method could be applicable in the performance improvement of small ship detection and the land masking, It was also found that a simple combination of coherence images from each co-polarised (HH) inter-look and cross-polarised (HV) inter-look data can provide much higher target-detection possibilities.

• Korean Journal of Soil Science and Fertilizer
• /
• v.48 no.5
• /
• pp.528-534
• /
• 2015

Green manure crops have been well recognized as the alternative for chemical fertilizer, especially N fertilizer, because of its positive effect on soil and the environment. Hairy vetch and green barley are the most popular crops for cultivation of rice in paddy field. This study was conducted to evaluate effects of hairy vetch and green barley on soil microbial community and chemical properties during short-term application (three years). For this study, treatments were composed of hairy vetch (Hv), green barley (Gb), hairy vetch + green barley (Hv+Gb), and chemical fertilizer without green manure crops (Con.). Hv+Gb treatment showed the highest microbial biomass among treatments. Principal component analysis (PCA) showed that PC1 (73.0 %) was affected by microbial biomass and PC2 (21.5 %) was affected by fungi, cy19:0/18:$1{\omega}7c$ (stress indicator). Combined treatment with hairy vetch and green barley could be more efficient than green manure crop treatment as well as chemical fertilizer treatment for improvement of soil microorganisms.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.18 no.2
• /
• pp.123-128
• /
• 1998

Legume winter cover crop hairy vetch(Vicia villosa Roth, HV) can supply mineral nitrogen for silage corn by HV cover killed. The purphose of this study was to understand changes of soil mineral N, yield and N uptake of silage corn by N level (0, 135kgFN/ha) and cover cmp(no cover crop: NCC, hairy vetch cover crop: HVC) at field of Crop Experiment Station in 1996. HV growth decreased soil mineral N concentration before seeding corn, but killed HV cover increased concentration of soil mineral N at surface soil (0~7.5cm) at six-leaf stage of corn. Total dry matter(DM) and N uptake of corn averaged over N level was more decreased in HVC than in NCC at silk stage, but N uptake of corn after silk was more increased in HVC than in NCC by N mineralized fiom HV killed, especially in OkgFNJha. N fertilization increased total DM and and N uptake of corn averaged over cover crop, especially more increased the DM and N uptake before silk stage. Early application of N fertilizer was recommendable in netillage silage corn using hairy vetch cover crop.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.3
• /
• pp.134-141
• /
• 2005

Cultivation of winter cover crops and its soil utilization for summer main crops in slope upland is very important at the respects of diminution of soil erosion and non-point pollution source. The effects of cover crop, hairy vetch as no-tillage or conventional tillage on prevention of soil erosion and reduction of chemical nitrogen fertilization were investigated in the slope upland with whiter clover living mulch (partial tillage) in Suwon for three years and with rye (conventional tillage) in Hongcheon for two years, respectively. In Suwon, amounts of soil lost by rainfall runoff decreased as much as 90% by hairy vetch-no tillage (HV-NT), white clover-partial tillage (WF-PT) together with the decrease of rainfall runoff compared to winter fallow with conventional tillage (WF-CT). In addition, amounts of weed also decreased as much as 80-90% by HV-NT and WF-PT. Corn yield decreased much at the plot of WF-PT mainly due to competition for soil water and nutrients between clover and corn at the early corn growth stage. On the contrary, corn yield increased by HV-NT compared to WF-CT regardless of weed control. In Hongcheon, amounts of soil eroded during winter season before corn seeding were reduced as much as 95% by cultivation of hairy vetch and rye compared to winter fallow. Amount of soil eroded during waxy corn growing season was reduced as much as 98% by HV-NT compared to WF-CT. Also, soil incorporation of hairy vetch and rye as green manure with conventional tillage at corn seeding time could reduce soil erosion as much as 70% compared to no soil cover with conventional tillage. Ear yields of waxy corn were increased 10% higher at hairy vetch green manure (HV-CT) without nitrogen fertilizer, 20% higher at HV-NT with standard nitrogen fertilizer, respectively than WF-CT. But ear yields of waxy corn were decreased by rye green manure (R-CT) and HV-NT at the condition of no nitrogen fertilizer. It was concluded that hairy vetch was better as winter cover crop to reduce both soil erosion and chemical nitrogen fertilizer simultaneously in slope upland than other cover crops.

• Proceedings of the Zoological Society Korea Conference
• /
• 1995.10b
• /
• pp.356-356
• /
• 1995

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1229-1231
• /
• 1995

XLPE cable, which has excellent electrical and thermal performance, has been widely used for HV transmission & distribution lines. The most important thing to produce the cable products having good performance is to set the optimal operating conditions of cable machinery. Because it is very difficult to measure the temperature of cable under curing process practically, it is necessary to evaluate the cable temperature by using the method to simulate real conditions numerically. In this work, We investigate the basic theory on transient heat transfer between curing tube and cable for making a numerical simulation program using computer. In this program, a differential equation is approximated by a infinite differential method and a few assumptions are used to simplify the model and minimize the calculation time of program.