• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.58-64
• /
• 2001

An investigation of the TMR(Track Misregistration) requirements to achieve the capacity of 80GBytes／Platter in 7200rpm disk drive system is reported. This paper also gives an overview of the PES(Position Error Signal) characteristics in the 57,500TPI disk drive to estimate the required 95,000TPI-system PES. The TMR measured by PES are presented and decomposed in order to identify the portions and their contributions of the spindle-disk system vibration and HSA(Head-Stack-Assembly) system vibration respectively. A comprehensive review on the servo system is also presented to provide the practical limits of the modem servo architecture into TMR budget design. The decomposed PES energy distribution shows that the spindle-disk pack vibration is one of the top-ranking sources of the total TMR budget and its percentage contribution is about 50％ considering all the other TMR sources.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.340.2-340
• /
• 2002

A practical implementation method of squeeze-film aeroelastic disk vibration damping and its practical design performance are presented to provide a solution method to meet the tight TMR(Track Mis-Registration) design budget of high-TPI HDDs. Most previous research results are mainly based on the component-level study in the 'open-cover state' which is far from the realistic operations HDD condition. (omitted)

• 한국자기학회지
• /
• 제8권6호
• /
• pp.395-399
• /
• 1998

평면 실리콘 헤드를 사용한 디스크 드라이브(hard disk:HDD) 시스템의 average bit error rate(ABER)를 계산하였다. ABER을 구하기 위해 3차원 유한 요소법을 사용하여 헤드 자장 분포를 구하고 error rate response surface(ERRS)를 구하엿다. 다음에 track misregistration(TMR)과 계산되어진 ERRS를 컨볼루션하여 ABER을 시뮬레이션 하였다. 허용할 수 잇는 에러 율이 10-6이라 하고 트랙 피치가 3.7$\mu$m일 때, 요구되는 TMR은 0.36$\mu$m이었다. 이는 트랙 피치의 9.7이었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.887-887
• /
• 2004

The areal density of the hard disk drive(HDD) has been increased due to technological advances recently. To achieve the high areal density magnetic recording requires an extremely small gap between the air-bearing surface (ABS) and disk. At the same time, the slider mass and size should be reduced to minimize the physical contact under the operational and environmental conditions. Almost all of 2.5＂HDD companies will get ready for adoption of FEMTO slider and already utilized the small slider. FEMTO and small size slider will be mainstream in the 2.5" and other small form factor HDD in the near future. In this study, the flying characteristic of FEMTO slider was examined. Based on the simulation, FEMTO slider is very stable in flying dynamic under the disk modulation, however the flying height sensitivity of the manufacturing tolerances is much bigger than PICO slider. And the other characteristics like impulse response and load/unload dynamic were also examined in this study.tudy.

• 정보저장시스템학회논문집
• /
• 제2권3호
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.413-418
• /
• 2004

Recently, the development of mobile devices demands information storage systems to use micro drive devices. 1-inch micro drive hard disk uses the load/unload(L/UL) technology to increase area recording density and reduce power consumption. Because micro drive has light actuator, effects of the flexible cable that is ignored in 3.5-inch hard disk drive is important to load/unload performances. In this paper, effects of flexible cable on load/unload performances are studied.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.736-741
• /
• 2004

In high-capacity disk drives with ever-growing track density, the allowable level of position error signal (PES) is becoming smaller and smaller. In order to achieve the high TPI disk drive, it is necessary to improve the writing accuracy during the STW(servo track writing) process through the reduction of TMR sources. Among the main contributors of the NRRO(Non-Repeatable Run-out) PES, the disk vibration and the HSA(head-stack assembly) vibration is considered to be one of the most significant factors. Also the most contributors of RRO(Repeatable Run- out) come from the contributors of NRRO which is written-in at the time of STW(servo track writing) process. In this paper, the experimental test result shows that the effect of NRRO on servo written-in RRO effectively can be reduced through a STW process under low dense medium condition such as semi-vacuum.

• 대한기계학회논문집A
• /
• 제26권1호
• /
• pp.196-202
• /
• 2002

In this work, we propose a new type of HDD suspension featuring shape memory alloy (SMA) actuator in order to prevent the contact between the slider and disk. The principal design parameters are obtained from the modal analysis using finite element analysis, and then the dynamic model is established to formulate the control scheme for Non-Contact Start/stop mode drive. Subsequently, a robust H$\_$$\infty$/ control algorithm is designed by integrating experimentally-Obtained SMA actuator dynamics to the proposed HDD suspension system. The controller is empirically realized and control results for the load/unload profiles are presented in time domain. In addition, the contact signal between the slider and disk is measured by the electrical resistance method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1615-1620
• /
• 2000

The extensive increase of the rotating speed of HDD (hard disk drive) has improved the performance of HDD. One of drawbacks, however, is that it increase noise level. For the systematic noise control of HDD, it is important to know the way in which each source of HDD contributes to resulting noise. A conventional method for contribution analysis by using statistical information, however, is not proper for HDD. This paper reviews the conventional method, and explains the reason why the method is not proper for HDD, even though it is possible to find the number of independent sources by using statistical information. This paper also shows an experimental result for the identification of the number of independent sources of HDD.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1391-1399
• /
• 2001

The AE measurement is one of the most convenient methods for detecting contacts between the slider and the disk. The AE method has been widely used in the investigation of the tribology of sliding interfaces due to its convenience. We examined the relationship between the AE signal and the flying height of a slider. We investigated the influence of the disk linear velocity on the AE rms signal by using the AE measurement system. The experiment also gives the relationship between the take-off velocity and the disk surface conditions. To investigate the behavior of the slider further, the variances of the AE signals are analyzed. The experimental results indicate that the increase in the magnitude of the AE rms signal does not necessarily mean the slider/disk contacts.