• Analytical Science and Technology
• /
• v.16 no.5
• /
• pp.391-398
• /
• 2003

Basic research for the determination of boron content in biological sample has been carried out using the PGAA facility of the 24MW research reactor(HANARO). For investigation of characteristics for the measurement condition, neutron flux and its homogeneity were measured at irradiating geometry. The size of thermal neutron beam collimated from beam guide is $2{\times}2cm^2$ at the sample position. The neutron flux measured was the range of $1.0{\sim}6.5{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$, and flux distribution from center within the radius of 4.5 mm and 9.0 mm was $5.77{\pm}0.71{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$ and $4.68{\pm}1.64{\times}10^7n{\cdot}cm^{-2}{\cdot}s^{-1}$, respectively. Accordingly, sample size is adjusted within 10 mm for a homogeneous irradiation of high quality. Measurement system is designed to reduce the background source by Compton scattering and to improve the analytical sensitivity. To investigate the energy calibration and Compton suppression effect of gamma-ray counting system, the background conditions on both of Compton and single-mode were measured using NaCl standard. On the other hand, degree of spectral interference for sodium 472 keV peak as a matrix effect in the sample is established for an accurate boron analysis, and then boron content in three certified reference materials (NIST SRM 1570a, 1547, 1573a) was measured by using two modes and the results were compared with each other.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.552-558
• /
• 2016

A control rod drive mechanism(CRDM) is a reactor regulating system, which inserts, withdraws or maintains a control rod within a reactor core to control the reactivity of the core. The CRDM for Jordan Research and Training Reactor with 5MW power has been designed and fabricated based on the HANARO’s experience through KAERI and DAEWOO consortium. This paper describes the seismic test results to demonstrate the operability, the drop performance and the structural integrity of CRDM during or after seismic excitations. The seismic tests are carried out under 5 OBE and 1 SSE loads at three Test Rigs simulating the reactor structure and the pool top. From the tests, the CRDM is smoothly driven without a malfunction of stepping motor under OBE load. The pure drop time under OBE and SSE loads is measured as 1.169s and 1.855s to meet the design requirement. Also, it is found that the CRDM maintains the structural integrity without a change of the function and natural frequency before and after seismic loads.

• Journal of Radiopharmaceuticals and Molecular Probes
• /
• v.8 no.1
• /
• pp.9-15
• /
• 2022

Anti-cancer and therapeutic effects using therapeutic radioisotopes have been demonstrated by various studies, and it is well-known that therapeutic radioisotopes are useful in cancer treatment. Recently, one of the therapeutic radioisotopes, scandium is emerging as a radioisotope applicable to PET imaging (⁴³Sc, ⁴⁴Sc) and therapy (⁴⁷Sc) in cancer theranostic approach. However, ⁴⁷Sc has little known radiobiological and therapeutic efficacy compared to other therapeutic radioisotopes. Here, we investigated the quality and therapeutic efficacy of ⁴⁷Sc radioisotope produced by our production/isolation technology at the research reactor 'HANARO' in KAERI (Korea Atomic Energy Research Institute). We showed that the therapeutic efficacy of ⁴⁷Sc, produced by our production/isolation technology, effectively suppressed epidermal growth factor receptor (EGFR)-targeted non-small cell lung cancer (NSCLC) cells. Consequently, these results suggest that the high quality of the produced ⁴⁷Sc by our production/isolation technology enables the development of therapeutic strategies for cancer treatment and radiopharmaceuticals using ⁴⁷Sc.

• Journal of Radiation Industry
• /
• v.17 no.4
• /
• pp.417-425
• /
• 2023

Lutetium(¹⁷⁷Lu), with its theranostic properties, is one of the most widely used radioisotopes and has a large share of the radiopharmaceutical market due to its many applications and targeted therapeutic research using lutetium-based radiopharmaceuticals. However, lutetium-based radiopharmaceuticals currently approved by the US Food and Drug Administration (FDA) are limited to the indications of gastrointestinal cancer, pancreatic neuroendocrine cancer and metastatic castration-resistant prostate cancer. To overcome these limitations, we aimed to demonstrate the feasibility of expanding the use of lutetium-based radiopharmaceuticals by verifying the availability and therapeutic efficacy of lutetium produced in a research reactor(HANARO). In this study, we confirmed the therapeutic efficacy of lutetium by using cancer cells from different types of cancer. In addition, we selected cancer biomarkers based on characteristics common to various cancer cells and compared and evaluated the therapeutic efficacy of lutetium by regulating the expression of target genes. The results showed that modulation of cancer biomarker gene expression resulted in higher therapeutic efficacy compared to lutetium alone. In conclusion, this study verified the potential use and therapeutic efficacy of lutetium based on the production of a research reactor (HANARO), providing fundamental evidence for the development of lutetium-based radiopharmaceuticals and the expansion of their indications.

• Journal of Radiation Industry
• /
• v.9 no.3
• /
• pp.111-117
• /
• 2015

In this paper, production of $^{166}Ho$ by double neutron capture from HANARO research reactor was evaluated. This production approach provides $^{166}Ho$ with high specific activity. $^{164}Dy$ is transmuted into $^{165g+m}Dy$ by (n,${\gamma}$) reaction, then $^{165g+m}Dy$ is transmuted into $^{166}Dy$ by (n,${\gamma}$) reaction. At the end of neutron irradiation, population of $^{166}Dy$ atoms reaches highest point. And $^{164}Dy$ exists as a mixture with $^{165m}Dy$, $^{165}Dy$, $^{166}Ho$ and $^{165}Ho$ at this point. To obtain $^{166}Ho$ with high specific activity, Ho isotopes from irradiated target is separated out. Then $^{166}Ho$ decayed from $^{166}Dy$ is eluted at radioactive equilibrium state. At each step, the number of relevant nuclide is calculated by the state equation. The neutron irradiation time for maximum $^{166}Dy$ is calculated for 283 hour. When 100 mg target of $Dy_2O_3$ (96.8% enriched $^{164}Dy$) is used, possible activity of $^{166}Ho$ is 3.54 Ci($1.31{\times}10^{11}Bq$). For separation efficiency of Dy/Ho is 99.99%, $^{166}Ho/Ho$ is 0.62.

• Nuclear Engineering and Technology
• /
• v.31 no.4
• /
• pp.365-374
• /
• 1999

A nuclear design of fission moly production targets for a research reactor, HANARO was peformed. It was found that the use of MCNP-4A, ORIGEN-2 code was reliable for the analysis of production characteristics of $^{99}$ Mo in a target fuel at an irradiation holes. A parametric study was done for the optimization of target location, target dimension, target shape and fuel materials. It was shown that a fuel thickness was the most sensitive parameters and electro-deposited target gave the highest 99Mo yield ratio. A pellet target with vibro-compaction powder, however, showed the largest production capacity and better engineering feasibility even with less yield ratio. Ten kinds of optimized target design for both LEU and HEU satisfied all the given design constraints. The most favorable design was the HEU ring-shaped electro-deposited target, considered the safety limit, production yield, chemical process easiness, yield ratio, and amount of radioactive waste.

• Nuclear Engineering and Technology
• /
• v.28 no.2
• /
• pp.150-161
• /
• 1996

A deformation model was developed to calculate the deformation of the uranium-silicide dispersion fuel (U$_3$Si-Al) elements for research reactors. The model was based on the elasto-plasticity theory and power-law creep theory. Also, isotopic swelling was assumed for the fuel meat and isotropic thermal expansion for the fuel meat and dadding. The new model calculated successfully the deformation of the fuels of HANARO and NRU (in Canada). As the most important result, it was shown that the primary deformation mechanism in the fuel meat was swelling and that in the cladding was creep. For all cases simulated, the maximum hoop stress at cladding outer surface was lass than 5MPa, probably well below the yield stress of the dadding, and finally, the volume change was predicted to be less than 10% in the whole burnup range.

• Journal of Radiation Protection and Research
• /
• v.48 no.1
• /
• pp.52-57
• /
• 2023

Background: Korea Atomic Energy Research Institute (KAERI) operates several nuclear research facilities licensed by Nuclear Safety and Security Commission (NSSC). The emergency preparedness requirements, GSR Part 7, by International Atomic Energy Agency (IAEA) request protection strategy based on the hazard assessment that is not applied in Korea. Materials and Methods: In developing the protection strategy, it is important to consider an accident scenario and its consequence. KAERI has tried the hazard assessment based on a hypothesis accident scenario for the major nuclear facilities. During the assessment, the safety analysis report of the related facilities was reviewed, the simulation using MELCOR, MACCS2 code was implemented based on a considered accident scenario of each facility, and the international guidance was considered. Results and Discussion: The results of the optimized protective actions were 300 m evacuation and 800 m sheltering for the High-Flux Advanced Neutron Application Reactor (HANARO), the evacuation to radius 50 m, the sheltering 400 m for post-irradiation examination facility (PIEF), 100 m evacuation or sheltering for HANARO fuel fabrication plant (HFFP) facility. Conclusion: The results of the optimized protective actions and its distances for the KAERI facilities for the maximum postulated accidents were considered in establishing the emergency plan and procedures and implementing an emergency exercise for the KAERI facilities.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.2
• /
• pp.179-184
• /
• 2009

The Fuel Test Loop(FTL) which is capable of an irradiation testing under a similar operating condition to those of PWR(Pressurized Water Reactor) and CANDU(CANadian Deuterium Uranium reactor) nuclear power plants has been developed and installed in HANARO, KAERI(Korea Atomic Energy Research Institute). It consists of In-Pile Section(IPS) and Out-of Pile System(OPS). The IPS, which is located inside the pool is divided into 3-parts; the in-pool pipes, the IVA(IPS Vessel Assembly) and the support structures. The test fuel is loaded inside a double wall, inner pressure vessel and outer pressure vessel, to keep the functionality of the reactor coolant pressure boundary. The IVA is manufactured by local company and the functional test and verification were done through pressure drop, vibration, hydraulic and leakage tests. The brazing technique for the instrument lines has been checked for its functionality and performance. An IVA has been manufactured by local technique and have finally tested under high temperature and high pressure. The IVA and piping did not experience leakage, as we have checked the piping, flanges, assembly parts. We have obtained good data during the three cycle test which includes a pressure test, pressure and temperature cycling, and constant temperature.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.655-659
• /
• 2003

The research reactor (TRIGA Mark-III(KRR-2)) was constructed and had been operated in 1972. In 1999 the radioisotope process units had stopped its operation due to normal operation of HANARO. In 2003 the core assembly was decommissioned by D&D program. The contact exposure rate on the core assembly and the rotary specimen rack are from 300mSv/h to 700mSv/h. This report describes the decontaminationing procedures, the health physics programs, and the waste management.