• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.913-920
• /
• 2006

Three-dimensional flow and aerodynamic loss in the tip-leakage flow region of a high-turning first-stage turbine rotor blade with a squealer tip have been measured with a straight miniature five-hole probe for the tip gap-to-chord ratio, h/c, of 2.0%. This squealer tip has a indent-to-chord ratio, $h/{st}/c$, of 5.5%. The results are compared with those for a plane tip $(h_{st}/c=0.0%)$. The squealer tip tends to reduce the mass flow through the tip gap and to suppress the development of the tip-leakage vortex. Therefore, it delivers lower aerodynamic loss in the near-tip region than the plane tip does. At the mid-span, however, the aerodynamic loss has nearly the same value for the two different tips.

• Progress in Superconductivity
• /
• 제3권1호
• /
• pp.111-114
• /
• 2001

Short-length and long-length Ni tapes were fabricated by powder processing, cold rolling and recrystallizatioon heat treatment. In the case of the short-length Ni tape, both in-plane and out-of-plane texture were less than $10^{\circ}$. In the case of the long-length Ni tape, the degree of texture is lower than that of the short-length Ni tape. The relationship between the texture formation and the processing parameter is reported.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1500-1502
• /
• 1997

We investigated the tracking and erosion resistance of the silicone rubber by Inclined-Plane Method. And, with the variation of the accelerated conditions such as the applied voltage and composition of contaminant, the change of the tracking characteristics according to such conditions was evaluated. The leakage current significantly increases with the increasing voltage, but the weight loss remains almost the same. The voltage above 5.0 kV isn't recommended because tracking breakdown occurs as fast as it does without erosion, and the typical discharge waveform was the form of rectifying wave.

• 한국통신학회논문지
• /
• 제22권4호
• /
• pp.605-610
• /
• 1997

An analysis method for the electromagnetic scattering of a Tm polarized plane wave from a periodic strip grating over a grounded dielectric slab is considered from the viewpoint of reflection grating problem. The parameters of strip gratings showing Bargg and Off-Bragg blazing phenomena at the frequency of 10GHz are derived teoretically. The strip grating structure is implemented using Aluminum plate(groung conductor), paraffin(dielectric material.epsilon.$_{r}$=2.24), and copper(strip conductor0.08m thickness). The experimental results(reflection power) of Bragg as well as Off-Bragg blazing phenomenon for TM polarized plane wave have been compared with the theoretical results and fairly good agreements between theory and experiment have been observed.d.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.663-665
• /
• 1993

An H-Plane waveguide component with arbitrary shape is analyzed using finite element technique(FEM) cooperated with boundary element method(BEM). For the application of BEM in the waveguide structure, a hybrid ray-mode representation of the waveguide Green's function is used. This technique is applied to the waveguide step load and the computed results are compared with the earlier theoretical results.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.104-109
• /
• 1994

This research describes some developments of computer-aided process planning and die design for hot forging products of H-shaped plane strain produced by the press. The system is composed of three main modules(process planning module, die design module and simulation module) which are used independently or in all. Systm capabilities include as follows: 1. In die design module, using the results of process planning module, the shape and size of bolcker and finish die in each operation are determined and the ouput id generated in graphic form for manufacturing drawing. 3. In simulation module, the flow pattern of workpiece and the load/stroke curve are approximately predicted. Design rules for process planning and die design are extracted from plasticity theories, handbooks, relevant references and empirical know-how of field experts in hot forging companies. The developed system provides poweful capabilities for process planning and die design of hot forging products.

• 천문학회보
• /
• 제46권2호
• /
• pp.66.2-66.2
• /
• 2021

We list up the Paα-emitting sources observed in the Carina Region (l = 276°-296°) using the MIRIS Paα Galactic Plane Survey data. A total of 201 sources are cataloged. Out of them, 118 sources are coincident with those in the WISE H II region catalog. 52 H II region candidates are newly confirmed as definite H II regions by detecting the Paα recombination lines. For the remaining 83 sources, we search the corresponding objects in the SIMBAD database. 26 point-like sources are associated with planetary nebulae or emission-line stars (such as Wolf-Rayet and Blue supergiant stars). Also, we carry out aperture photometry to measure Paα fluxes for the sources that show circular features without overlapping with other bright sources. For the whole Galactic Plane, the complete Paα-emitting source catalog is in progress.

• Journal of Animal Science and Technology
• /
• 제54권6호
• /
• pp.449-454
• /
• 2012

The present study was performed to investigate the effects of the plane of nutrition on growth performance and meat quality traits, especially marbling and PSE (pale, soft, and exudative), in finishing pigs. One hundred and four barrows and 102 gilts born to Yorkshire ${\times}$ Landrace dams and Duroc sires were randomly allocated to 16 pens at approximately 80-kg body weight, with 13 animals housed per pen except for two pens. Each eight pens received a diet containing either 3.4 Mcal ME/kg and 0.98% total lysine (high plane) or 3.1 Mcal ME/kg and 0.81% total lysine (medium plane). All animals were slaughtered at approximately 112 kg BW on an average, after which the Longissimus muscle (LM) was analyzed physicochemically. The ADG, ADFI, gain:feed as well as marbling score did not differ between the two dietary groups, whereas backfat thickness was greater in the high-plane group than in the medium-plane group (24.1 vs. 22.5 mm P<0.05). No LM exhibited PSE, i.e. $L^*$ (lightness) > 50, pH < 6.0 and drip loss > 5.0%, nor were these PSE-related variables influenced by the dietary treatment. Contents of crude protein and fat in LM did not differ between the two dietary groups. In conclusion, the present results suggest that growth performance and the occurrence of the PSE or 'watery' carcass are not influenced significantly by increasing the plane of nutrition in finishing pigs when the finisher is adequate nutritionally for supporting maximal lean growth. However, increasing the plane of nutrition is likely to result in an increase in fat deposition.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2018년도 춘계학술대회
• /
• pp.55-56
• /
• 2018

본 논문에서는 H-모양 공진 개구를 이용한 평면 기판의 유전율 특성 분석 방법을 제안하였다. 이를 위해 마이크로스트립 전송선로의 접지면에 H-모양 공진 개구를 추가하여 대역 저지 필터를 생성하였다. 마이크로스트립 전송선로의 접지면 뒤에 2 mm 두께의 평면 기판을 놓고 기판의 유전율 변화에 따른 공진주파수의 변화를 조사하였다. 기존의 상보 분할 링 공진기 구조를 사용하였을 때와 비교하여 기준 공진주파수에 대한 주파수의 변화 비가 커짐을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제38권5호
• /
• pp.399-406
• /
• 2014

본 연구에서는 압력면윙렛/흡입면스퀼러형 터빈 동익 팁에 대하여 익렬 하류에서 3차원 유동 및 압력손실을 측정하였다. 팁간극비 h/s = 1.36%에 대하여, 흡입면스퀼러의 높이는 $h_s/s$ = 3.75%로 일정하게 유지하고, 압력면윙렛의 폭은 w/p = 2.64%, 5.28%, 7.92%, 10.55% 등으로 변화시키면서 실험을 수행하였다. 그 결과, 본 연구의 팁은 평면팁 대비 통로와류 영역에서 압력손실의 저감 효과가 매우 뛰어났지만, 팁누설와류 영역에서는 오히려 압력손실을 크게 증가시켰다. 본 연구의 질량평균 압력손실은 평면팁에 비해 크게 낮았지만, 전면스퀼러팁보다는 더 크게 나타났다. 압력면윙렛의 폭이 증가할수록 질량평균 압력손실은 감소하는 경향을 보였다.