• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.551-555
• /
• 2004

The two-transformer full bridge (TTFB) PWM converter has two transformers which act as the output inductor as well as the main transformer, i.e. as the forward and the flyback transformer. Although the doubled leakage inductor of the TTFB makes it easier to achieve the zero-voltage switching (ZVS) of the lagging leg switch along the wide load range, it instigates a serious voltage ringing in the secondary rectifier diodes, which would require the dissipative snubber circuit, cause the serious power dissipation, and increase the voltage stress across those diodes. To overcome these problems, a, new lossless diode-clamp rectifier (LDCR) is employed as the output rectifier, which helps the voltage across rectifier diodes to be clamped on a half the output voltage $(V_o/2)$ or the output voltage $(V_o)$. Therefore, no dissipative snubber for rectifier diodes is needed and a high efficiency as well as low noise output voltage can be realized. The operations, analysis and design consideration of proposed converter are presented in this paper. To verify the validity of the proposed converter, experimental results from a 425W, 385-170Vdc prototype for the plasma display panel (PDP) sustaining power module (PSPM) are presented.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.304-308
• /
• 2001

This paper presents a novel prototype of ZCS-PFM high frequency series resonant inverter using IGBT power module for electromagnetic induction eddy current-heated roller in copy and printing machines. The operating principle and unique features of this voltage source half bridge inverter with two additional soft commutation inductor snubber are presented including the transformer modeling of induction heated rolling drum. This soft switching inverter can achieve stable zero current soft commutation under a discontinuous and continuous resonant load current for a widely specified power regulation processing. The experimental results and computer-aided analysis of this inverter are discussed from a practical point of view.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.246-252
• /
• 2011

In this paper proposes the soft-switching boost converter and MPPT control for improving the efficiency of PV system. The proposed converter designed H-bridge auxiliary resonant circuit. By this circuit, all of the switching devices perform the soft switching under the zero voltage and zero current condition. Therefore the periodic switching losses can be decreased at turn on, off. The soft switching boost converter designs for 1.5[kW] solar module of the power conversion. Thus, this soft switching boost converter is simulated by MATLAB simulation using Newton-Method algorithm. As a result, Proposed Soft Switching Converter compared to a typical boost converter switching loss was reduced about 61%. And the overall system efficiency was verified to increase about 3.3%.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1316-1323
• /
• 2016

Multilevel inverters (MLIs) have been preferred over conventional two-level inverters due to their inherent properties such as reduced harmonic distortion, lower electromagnetic interference, minimal common mode voltage, ability to synthesize medium/high voltage from low voltage sources, etc. On the other hand, they suffer from an increased number of switching devices, complex gate pulse generation, etc. This paper develops an ingenious symmetrical MLI topology, which consumes lesser component count. The proposed level dependent sources concoction multilevel inverter (LDSCMLI) is basically a multilevel dc link MLI (MLDCMLI), which first synthesizes a stepped dc link voltage using a sources concoction module and then realizes the ac waveform through a conventional H-bridge. Seven level and eleven level versions of the proposed topology are simulated in MATLAB r2010b and prototypes are constructed to validate the performance. The proposed topology requires lesser components compared to recent component reduced MLI topologies and the classical topologies. In addition, it requires fewer carrier signals and gate driver circuits.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.954-955
• /
• 2015

본 논문에서는 기존 직렬결합 커패시터 입력단을 갖는 7-레벨 인버터에 커패시터 전압균형 제어법을 적용하여 출력 전압의 중간레벨 구간이 제대로 형성되지 않는 문제점을 해결하고자 한다. 기존에 제시된 직렬결합 커패시터 입력단 구성을 갖는 7-레벨 인버터는 2개의 양방향 스위치모듈과 3개의 직렬 연결된 커패시터를 이용한 변형된 Cascaded H-bridge 인버터이다. 기존 논문에서는 입력 전압원으로부터 3개의 직렬 연결된 커패시터의 충전을 통해 레벨을 형성하는 과정에서 커패시터 전압불균형 문제를 해결하지 못하여 결국 출력전압레벨이 7-레벨에서 5-레벨로 감소하는 것을 볼 수 있다. 본 논문에서는 세 개의 직렬결합된 커패시터중 중앙에 위치한 커패시터의 충 방전량을 조절하여 커패시터 전압불균형 문제를 해결한다. 제어법의 타당성은 PSIM 기반의 컴퓨터 시뮬레이션을 통하여 기존 스위칭 제어법과 비교하여 검증한다.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.128-130
• /
• 2006

We introduce 2[MVA] 3300[V] 7-level voltage source inverter system developed by POSCON and describe the main characteristics of inverter system i.e. PWM converter, H-bridge power module, phase shifted carrier PWM The PWM converter is a three-phase boost converter, which operates in a 4-quadrant and in a nearly unit displacement power factor. Experimental waveforms are also presented to verify the proposed method and performance of the developed system.

• Journal of Internet Computing and Services
• /
• v.17 no.4
• /
• pp.11-17
• /
• 2016

In this paper, we proposed a multi-viewer system with multiple HD cameras based AVB(Audio Video Bridge) ethernet cable using IP networking, and FPGA(Xilinx Zynq 702) for bus safety systems. This AVB (IEEE802.1BA) system can be designed for the low latency based on FPGA, and transmit real-time with HD video and audio signals in a vehicle network. The proposed multi-viewer platform can multiplex H.264 video signals from 4 wide-angle HD cameras with existed ethernet 1Gbps. and 2-wire 100Mbps cables. The design of Zynq 702 based low latency to H.264 AVC CODEC was proposed for the minimization of time-delay in the HD video transmission of car area network, too. And the performance of PSNR(Peak Signal-to-noise-ratio) was analyzed with the reference model JM for encoding and decoding results in H.264 AVC CODEC. These PSNR values can be confirmed according the theoretical and HW result from the signal of H.264 AVC CODEC based on Zynq 702 the multi-viewer with multiple cameras. As a result, proposed AVB multi-viewer platform with multiple cameras can be used for the surveillance of audio and video around a bus for the safety due to the low latency of H.264 AVC CODEC design.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.248-256
• /
• 2005

This paper presents the design method of the DC/DC converter using flat transformer which is suitable for midium or large capacity and high density power supply. Flat transformer module is composed and manufactured of multi-transformers in parallel and has a number of parallel single turn secondary windings. Therefore, its leakage inductance is highly decreased and it is more suitable for high frequency operation than conventional one. In this paper, we manufactured and tested 750W AC/DC converter with variable output powers to verify the performance of the flat transformer.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.490-497
• /
• 2016

The analysis of the switch status of each unit module of a cascaded multi-level inverter reveals that the working condition of the switch of a chopper arm causes unnecessary switching under the conventional unipolar sinusoidal pulse width modulation (SPWM). With an increase in the number of cascaded multilevel inverters, the superposition of unnecessary switching gradually occurs. In this work, we propose an improved SPWM strategy to reduce switching in cascaded multilevel inverters. Specifically, we analyze the switch state of the switch tube of a chopper arm of an H-bridge unit. The redundant switch is then removed, thereby reducing the switching frequency. Unlike the conventional unipolar SPWM technique, the improved SPWM method greatly reduces switching without altering the output quality of inverters. The conventional unipolar SPWM technique and the proposed method are applied to a five-level inverter. Simulation results show the superiority of the proposed strategy. Finally, a prototype is built in the laboratory. Experimental results verify the correctness of the proposed modulation strategy.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.11
• /
• pp.171-179
• /
• 1997

This paper describes a nesting system of a computer-aided design of blanking and piercing for irregularly shaped sheet metal products. An approach to the system is based on knowledge-based rules. A nesting system is designed by considering several factors, such as utilization ratio which minimises the scrab for single or pairwise operation, bridge width, grain orientation and design requirements which maximise the strength of the part when subsequent bending is involve. Therefore this system which was implemented blank layout and strip layout module can carry out a nesting with a best utilization and a process planning for irregular shaped sheet metal products in single or pairwise operation and generate the blank layout and strip layout in graphic forms. Knowledges for a nesting and a process planning are extracted from plasticity theories, relevant references and empirical know-hows of experts in blanking industries. This provides its efficiency and effectiveness for nesting irregularly shaped sheet metal products.