• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.181-190
• /
• 2007

This paper presents a novel circuit topology of a DC bus line series switch and parallel snubbing capacitor-assisted soft-switching PWM full-bridge inverter type DC-DC power converter with a high frequency planar transformer link, which is newly developed for high performance arc welding machines in industry. The proposed DC-DC power converter circuit is based upon a voltage source-fed H type full-bridge soft-switching PWM inverter with a high frequency transformer. This DC-DC power converter has a single power semiconductor switching device in series with an input DC low side rail and loss less snubbing capacitor in parallel with the inverter bridge legs. All the active power switches in the full-bridge arms and DC bus line can achieve ZCS turn-on and ZVS turn-off transition commutation. Consequently, the total switching power losses occurred at turn-off switching transition of these power semiconductor devices; IGBTs can be reduced even in higher switching frequency bands ranging from 20 kHz to 100 kHz. The switching frequency of this DC-DC power converter using IGBT power modules can be realized at 60 kHz. It is proved experimentally by power loss analysis that the more the switching frequency increases, the more the proposed DC-DC power converter can achieve a higher control response performance and size miniaturization. The practical and inherent effectiveness of the new DC-DC converter topology proposed here is actually confirmed for low voltage and large current DC-DC power supplies (32V, 300A) for TIG arc welding applications in industry.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.3
• /
• pp.125-130
• /
• 2014

This paper is research result for a development of solar cell silicon ingot glowing(SCSIG) PWM converter system for 120[kW] 3[kA]. The system include 3-phase AC-DC rectifier diode converter of input voltage AC 460[V] and 60[Hz], DC-AC single phase full bridge PWM inverter of high frequency, AC-DC single-phase full wave rectifier using center-tapped of transformer for low voltage 50[V] and large current 3,000[A], carbon resistor load 0.2 [$m{\Omega}$]. PWM switching frequency for IGBT inverter control set 15KHz. The suggested researching contents are designed data sheets of power converter system, PSIM simulation, operating characteristics and analysis results of developed SCSIG system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.33-41
• /
• 2014

This paper is research result for a development of sapphire silicon ingot glowing(SSIG) PWM converter system for 80kW 10kA. The system include 3-phase AC-DC diode rectifier of input voltage AC 380V and 60Hz, DC-AC single phase full bridge PWM inverter of high frequency, AC-DC single-phase full wave rectifier using center-tapped of transformer for low voltage 8.0V and large current 10,000A of output specification, tungsten resistor load 0.1[$m{\Omega}$]. PWM switching frequency for IGBT inverter control set 30kHz. The suggested researching contents are designed data sheets of power converter system, PSIM simulation, operating characteristics and analysis results of developed SSIG system. This paper propose

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1270-1273
• /
• 2000

A novel zero voltage and zero current switching (ZVZCS) full bridge (FB) PWM converter is proposed. The new converter improves the drawbacks of the previously proposed ZVZCS FB PWM converters [1-5]. A simple auxiliary circuit with neither lossy components nor active switches achieves ZVZCS of the primary switches. Since the proposed converter has many advantages such as simple auxiliary circuit, high efficiency, and low voltage stress of the rectifier diode, it is very attractive for the high power applications. The principles of operation and design considerations are presented. The experimental verifications from 2.5kW prototype converter operating at 70kHz are presented.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.251-255
• /
• 2005

This paper proposes a new soft switching technique for a phase-shift controlled bi-directional DC-DC converter. The described converter employs a low profile high frequency transformer and two active full-bridge converters for bidirectional power flow capability. A new soft switching technique is proposed, which guarantees soft switching over wide range (no load to full load) without any additional circuit components. In the proposed switching scheme, the switch pairs in the diagonal position of the converter each are turned on/off simultaneously by the switching signals with a variable duty ratio depending on the phase shift amount, and the converter is operated without freewheeling interval.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.147-149
• /
• 1998

In this paper, zero voltage switched half bridge converter and an active-clamped, zero voltage switched forward converter equipped with self-driven synchronous rectifier is designed and investigated for high efficiency BC-DC converter. A synchronous rectifier is has a lower conduction power loss than shottky diode rectifier. The purpose of this paper is to investigate the effect of parasitic inductance in a synchronous rectifier of DC-DC converters and examine overall efficiency of zero voltage switched DC-DC converters.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1634-1640
• /
• 2012

This paper develops the high-efficiency drive system of the small-size electric vehicles (EVs) driven by the brushed dc motors. A power circuit for driving the dc motor is designed with the H-bridge circuit and buck converter by considering both the efficiency and cost. In order to change smoothly the rotating direction of dc motor driven by the proposed power circuit, an operating sequence for both the field current and the armature voltage according to an accelerator pedal angle is suggested. Through the simulation studies and experimental results with the low-cost 8-bit AVR, the performances of the proposed methods are verified.

• Proceedings of the KIPE Conference
• /
• 2004.11a
• /
• pp.49-53
• /
• 2004

High density power supply technology has been researched over the last few years. In this paper, integrated LLCT(Inductor-Inductor-Capacitor-Transformer) structure is described for use in the half-bridge series resonant converter. The structure is analysed by means of FEMM(Finite Element Method Magnetics) and the experimental results of an U structure for a 300W converter we presented.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.355-357
• /
• 1999

Single-Phase multi-level AC-DC converter that is composed of diode bridge and switch is proposed. The number of the supply current level is depending on the individual current level of the converter. A converter circuit, the number of the level is equal to $2^{M+1}-1$, where M is the number of Switching Converter. The proposed circuit has converter with 31 current levels. When the number of current level is increased, smoother sinusoidal waveform can be obtained directly and it is possible to control the supply current almost continuously from zero to maximum without generating high voltage step changes as pulse with modulation technology. The technique illustrates its validity and effectiveness through the PSIM.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.491-495
• /
• 2001

Compare with diode or thyristor bridge AC/DC converter, the 3 phase PWM converter has some merits of low THD and unit power factor. So, in many critical application like as UPS, using PWM converter is the trends. 3 phase PWM converter had been studied widely already. But analytical design procedure can not found from publication for hardware design and controller design. So, in this paper, 3 phase PWM converter analysis review was given. And from the DC analysis result, parameter design was done. From the AC model, the voltage controller and current controller was designed. The gain of controllers was calculated by analytical method.