• Journal of the Korean Vacuum Society
• /
• v.6 no.4
• /
• pp.348-353
• /
• 1997

Hydrogenated amorphous carbon(a-C:H) films were deposited on p-type Si(100) by DC saddle-field plasma enhanced CVD to investigate the effect of substrate bias on optical properties and structural changes. They were deposited using pure methane gas at a wide range of substrate bias at room temperature and 90 mtorr. The substrate bias voltage ($V_s$) was employed from $V_s=0 V$ to $V_s=400 V$. The information of optical properties was investigated by photoluminescence and transmitance. Chemical bondings of a-C:H have been explored from FT-IR and Raman spectroscopy. The thickness and relative hydrogen content of the films were measured by Rutherford backscattering spectroscopy (RBS) and elastic recoil detection (ERD) technigue. The growth rate of a-C:H film was decreased with the increase of $V_s$, but the hydrogen content of the film was increased with the increase of $V_s$. The a-C:H films deposited at the lowest $V_s$ contain the smallest amount of hydrogen with most of C-H bonds in the of $CH_2$ configuration, whereas the films produced at higher $V_s$ reveal dominant the $CH_3$ bonding structure. The emission of white photoluminescence from the films were observed even with naked eyes at room temperature and the PL intensity of the film has the maximum value at $V_s$=200 V. With $V_s$ lower than 200 V, the PL intensity of the film increased with V, but for V, higher than 200 V, the PL intensity decreased with the increase of $V_s$. The peak energy of the PL spectra slightly shifted to the higher energy with the increase of $V_s$. The optical bandgap of the film, determined by optical transmittance, was increased from 1.5 eV at $V_s$=0V to 2.3 eV at $V_s$=400 V. But there were no obvious relations between the PL peak and the optical gap which were measured by Tauc process.

• Restorative Dentistry and Endodontics
• /
• v.35 no.3
• /
• pp.211-221
• /
• 2010

Proteoglycan is highly hydrophilic and negatively charged which enable them attract the water. The objective of study was to investigate the effects of Proteoglycan on microtensile bond strength of dentin adhesives and on architecture of dentin collagen matrix of acid etched dentin by removing the chondroitin sulphate attached on Proteoglycan. A flat dentin surface in mid-coronal portion of tooth was prepared. After acid etching, half of the specimens were immersed in 0.1 U/mL chondroitinase ABC (C-ABC) for 48 h at $37^{\circ}C$, while the other half were stored in distilled water. Specimens were bonded with the dentin adhesive using three different bonding techniques (wet, dry and re-wet) followed by microtensile bond strength test. SEM examination was done with debonded specimen, resin-dentin interface and acid-etched dentin surface with/without C-ABC treatment. For the subgroups using wet-bonding or dry-bonding technique, microtensile bond strength showed no significant difference after C-ABC treatment (p > 0.05). Nevertheless, the subgroup using rewetting technique after air dry in the Single Bond 2 group demonstrated a significant decrease of microtensile bond strength after C-ABC treatment. Collagen architecture is loosely packed and some fibrils are aggregated together and relatively collapsed compared with normal acid-etched wet dentin after C-ABC treatment. Further studies are necessary for the contribution to the collagen architecture of noncollagenous protein under the various clinical situations and several dentin conditioners and are also needed about long-term effect on bond strength of dentin adhesive.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.18 no.1
• /
• pp.99-132
• /
• 1992

Polypeptide has been used broadly as an active ingredient in cosmetics We thought it is very important to investigate the adsorption behavior of polypeptide in order to pre-estimate the effect of these polypeptides. For the study of polypeptide adsorption, we have investigated complex formation of basic homopolypeptides, poly(L-proline) Form I [PLP(I)], Form II [PLP(II)] and poly(4-hydroxy-L-proline) (PHLP) with acidic homopolypeptides, poly(L-glutamic acid) (PLGA), poly(D-glutamic acid) (PDGA) and poly(L-aspartic acid) (PLAA) through hydrogen bonding in a hydroalcoholic medium with viscometer, 1ight scatter, pH meter and circular dicroism (CD). The polypeptides used in this study have helical structure in some conditions. The result exhibited that al 1 the complexes were formed as the composition of basic/acidic homopolypeptide : L:2 irrespective of the complex systems used. A more favorable complex is formed in the PLP(II)-PLGA system than PHLP-PLGA because PLP(II) has a more flexible helical conformation, whereas PHLP has a more rigid helical conformation. The right-handed helix PLGA formed the complex favorably and quickly with the left-handed helix PLP(II), whereas the left-handed helix PDGA formed the complex favorably with the right-handed helix PLP(I). The effect of side chain of the acidic homopolypeptides on the complexation was also studied. The result showed that more favorable condition for the complexation was PLGA-PLP(II) system which has longer side chain at acidic homopolypeptide than PLAA - PLP(II). All the above facts were well supported by CD measurement for the complex systems. By the CD spectra for the complexes we could deduce the conformational change of each homopolypeptide in the complexes On the basis of the above results, we performed the adsorption test of PLP(I, II) and PHLP on the hair having a left-handed helix. The adsorption amount of each polypeptide was analyzed by HPLC. The result showed that PLP(I) was adsorbed more than PLP(II), PLP(II) was adsorbed more than PHLP on the hair. On adsorbing polypeptides having a helical structure on the hair through hydrogen bonding, it could be concluded that the helical polypeptides having the opposite directional structure to the hair are adsorbed more than those having the same directional structure with the hair and also the polypeptides having a flexible conformation are adsorbed more than those having a rigid conformation.

• Economic and Environmental Geology
• /
• v.56 no.5
• /
• pp.603-618
• /
• 2023

This study focused on evaluating the suitability of the WRK (waste repository Korea) bentonite as a buffer material in the SNF (spent nuclear fuel) repository. The U (uranium) adsorption/desorption characteristics and the adsorption mechanisms of the WRK bentonite were presented through various analyses, adsorption/desorption experiments, and kinetic adsorption modeling at various pH conditions. Mineralogical and structural analyses supported that the major mineral of the WRK bentonite is the Ca-montmorillonite having the great possibility for the U adsorption. From results of the U adsorption/desorption experiments (intial U concentration: 1 mg/L) for the WRK bentonite, despite the low ratio of the WRK bentonite/U (2 g/L), high U adsorption efficiency (>74%) and low U desorption rate (<14%) were acquired at pH 5, 6, 10, and 11 in solution, supporting that the WRK bentonite can be used as the buffer material preventing the U migration in the SNF repository. Relatively low U adsorption efficiency (<45%) for the WRK bentonite was acquired at pH 3 and 7 because the U exists as various species in solution depending on pH and thus its U adsorption mechanisms are different due to the U speciation. Based on experimental results and previous studies, the main U adsorption mechanisms of the WRK bentonite were understood in viewpoint of the chemical adsorption. At the acid conditions (＜pH 3), the U is apt to adsorb as forms of UO₂²⁺, mainly due to the ionic bond with Si-O or Al-O(OH) present on the WRK bentonite rather than the ion exchange with Ca²⁺ among layers of the WRK bentonite, showing the relatively low U adsorption efficiency. At the alkaline conditions (>pH 7), the U could be adsorbed in the form of anionic U-hydroxy complexes (UO₂(OH)₃^-, UO₂(OH)₄^2-, (UO₂)₃(OH)₇^-, etc.), mainly by bonding with oxygen (O^-) from Si-O or Al-O(OH) on the WRK bentonite or by co-precipitation in the form of hydroxide, showing the high U adsorption. At pH 7, the relatively low U adsorption efficiency (42%) was acquired in this study and it was due to the existence of the U-carbonates in solution, having relatively high solubility than other U species. The U adsorption efficiency of the WRK bentonite can be increased by maintaining a neutral or highly alkaline condition because of the formation of U-hydroxyl complexes rather than the uranyl ion (UO₂²⁺) in solution,and by restraining the formation of U-carbonate complexes in solution.

• Journal of the Korean Chemical Society
• /
• v.37 no.5
• /
• pp.473-476
• /
• 1993

Dipropargyldiphenylmetane, $C_{19}H_{16}, crystallizes in a monoclinic space group $C2/_c$$ with a = 11304(3), b = 20.799(5), c = 6.622(2)${\AA}$, ${\beta} = 112.8(3)^{\circ}$, Z = 4, V = 1435.3${\AA}^3,\;F(000)\;=\;520,\;D_c\;=\;1.14g{\cdot}cm^{-3}$ and ${\mu}\;=\;0.32\;cm^{-1}$. The structure was solved by direct methods and all non-H atoms were identified in the E-map. The final refinement gave R = 0.055 from 1328 unique observed reflections with I $\geq$ -1.0 $\sigma(I).$ The molecule belongs to the point group $C_2$ of Symmetry by possessing the 2-fold axis which coincides witeh the crystallographic symmetry axis in the unit cell. The linear propargyl moiety is nearly $perpendicular(94.2)^{\circ}$ to the molecular plane of the benzene ring. The internal angle of methane carbon atoms in $108.1(1)^{\circ}$, bonding to the benzene and the propargyl moiety with the bond lengths of 1.530(2) and $1.560(2)\AA$, respectively. The shortest contant between the molecules is $3.538(2)\AA$ between C(9) and C(9) (-x, y, -1/2-z).

• Bulletin of the Korean Chemical Society
• /
• v.26 no.12
• /
• pp.1946-1952
• /
• 2005

New group 15 organometallic compounds, M$(phenanthrenyl)_3$ (M = P (1), Sb (2), Bi (3)) have been prepared from the reactions of 9-phenanthrenyllithium with $MCl_3$. A reaction of 9-(diphenylphosphino)phenanthrene with 2,6-diisopropylphenyl azide led to the formation of (phenanthrenyl)${(Ph)}_2P$=N-(2,6-$^iPr_2C_6H_3$) (4). The crystal structures of 2 and 4 have been determined by single-crystal X-ray diffractions, both of which crystallize with two independent molecules in the asymmetric unit. Compound 2 shows a trigonal pyramidal geometry around the Sb atom with three phenanthrenyl groups being located in a screw-like fashion with an approximately $C_3$ symmetry. A significant amount of CH- -$\pi$ interaction exists between two independent molecules of 4. The phosphorus center possesses a distorted tetrahedral environment with P-N bond lengths of 1.557(3)$\AA$ (P(1) N) and 1.532(3)$\AA$ (P(2)-N), respectively, which are short enough to support a double bond character. One of the most intriguing structural features of 4 is an unusually diminished bond angle of C-N-P, attributable to the hydrogen bonding of N(1)-H(5A) [ca. 2.49$\AA$ between two adjacent molecules in crystal packing. The compounds 1-3 show purple emission both in solution and as films at room temperature with emission maxima ($\lambda_{max}$) at 349, 366, and 386 nm, respectively, attributable to the ligand centered $\pi$ $\rightarrow$ $\pi^\ast$ transition in phenanthrene contributed by the lone pair electrons of the Gp 15 elements. Yet the nature of luminescence observed with 4 differs in that it originates from $\pi$ (diisopropylbenzene)-$\pi^\ast$ (phenanthrene) transitions with the $\rho\pi$contribution from the nitrogen atom. The emission maximum of 4 is red-shifted ranging 350-450 nm due to the internal charge transfer from the phenanthrenyl ring to the N-arylamine group as deduced from the ab initio calculations.

• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.79-90
• /
• 2007

Prototype of $800{\ell}$ vacuum web coater (Vic Mama) consisting of ion source with low energy less than 250 eV for high speed surface modification and 4 magnetron sputter cathodes was designed and constructed. Its performance was evaluated through fabricating the adhesiveless flexible copper clad laminate (FCCL). Pumping speed was monitored in both upper noncoating zone pumped down by 2 turbo pumps with 2000 l/sec pumping speed and lower surface modification and sputter zone vacuumed by turbo pumps with 450 1/sec and 1300 1/sec pumping speed respectively. Ion current density, plasma density, and uniformity of ion beam current were measured using Faraday cup and the distribution of magnetic field and erosion efficiency of sputter target were also investigated. With the irradiation of ion beams on polyimide (Kapton-E, $38{\mu}m$) at different fluences, the change of wetting angle of the deionized water to polyimide surface and those of surface chemical bonding were analyzed by wetting anglometer and x-ray photoelectron spectroscopy. After investigating the deposition rate of Ni-Cr tie layer and Cu layer was investigated with the variations of roll speed and input power to sputter cathode. FCCL fabricated by sputter and electrodeposition method and characterized in terms of the peel strength, thermal and chemical stability.

• The Journal of the Korea Contents Association
• /
• v.9 no.10
• /
• pp.451-463
• /
• 2009

The purpose of this research is to develop thin film materials and fabrication process for efficient $TiO_2$/CdTe solar cells. In this work photocatalyst titanium dioxide was prepared by sol-gel procedure according to reaction condition, the mole ratio of $H_2O$/TTIP, pH of solution and aging condition of powder. The prepared titanium dioxide was thermally treated from 300 to $750^{\circ}C$. Maximum intensity of anatase phase of titanium dioxide was achieved by calcination at $600^{\circ}C$ for 2 hr. And it was mixture of anatase and rutile phase when temperature of calcination was $750^{\circ}C$. It has been known that the properties of synthesized titanium dioxide according to aging time and calcination temperature was converted to anatase phase crystal on increasing of aging time. Also the current density has been increased with aging time and temperature, the efficiency has been increased with because of reason on above results. The formation of chemical bonding on oxygen and cadmium telluride under oxygen circumstances had been observed, and oxygen of thin film surface on cadmium telluride had been decreased with the treatment of chromate and hydrazine. As results had been shown that the energy conversion efficiency of cadmium telluride use by rapidly treatmented heat at the condition of $550^{\circ}C$ under air circumstance got 12.0%, 6.0% values according to $0.07cm^2$, $1.0cm^2$ surface area, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.34-42
• /
• 2000

Recently, there is a growing need to develope small-size RF chip inductors operating to GHz to realize high-performance, micro-fabricated wireless communication products. For the development of high-performance RF chip inductors, however, the ferrite-based chip inductors can not be used above 300MHz due to the limitation of the permeability of this material. In this work, small-size, high-performance RF chip inductors utilizing amorphous $Al_2O_3$ core material were investigated. Copper (Cu) with 40${\mu}m$ diameter was used as the coils and the chip inductor size fabricated in this work is $2.1mm{\times}1.5mm{\times}1.0mm$. The external current source was applied after bonding Cu coil leads to gold pads electro-plated on the bottom edges of a core material. The composition of core materials was measured using a EDX. High frequency characteristics of the inductance (L), quality factor (Q), and impedance (Z) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The developed inductors have the self-resonant frequency (SRF) of 1 to 3.5 GHz and exhibit L of 22 to 150 nH. The L of the inductors decreases with increasing the SRF. The Z of the inductors has the maximum value at the SRF and the inductors have the quality factor of 70 to 97 in the frequency range of 500 MHz to 1.5 GHz.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.500-506
• /
• 1999

We designed and fabricated a bidirectional optical transceiver module for low cost access network. An integrated chip forming a pin-PD on an 1.3 urn FP-LD was assembled by flip-chip bonding on a Si optical bench, a single mode fiber with an angled end facet was aligned passively with the integrated chip on V-groove of Si-optical bench. Gaussian beam theory was applied to evaluate the coupling coefficients as a function of some parameters such as alignment distance, angle of fiber end facet, vertical alignment error. The theory is also used to search the bottle-neck between transmittance and receiving coupling efficiency in the bi-directional optical system. Tn this paper, we confirmed that reduction of coupling efficiency by the vertical alignment error between laser beam and fiber core axis can be compensated by controlling the fiber facet angle. In the fabrication of sub-module, a'||'&'||' we made such that the fiber facet have a corn shape with an angled facet only core part, the reflection of transmitted laser beam from the fiber facet could be minimized below -35 dE in alignment distance of 2: 30 /J.m. In the same condition, transmitted output power of -12.1 dEm and responsivity of 0.2. AIW were obtained.