• Steel and Composite Structures
• /
• 제8권5호
• /
• pp.389-402
• /
• 2008

In December 2005, one(A) of the two pre-engineered warehouse buildings in the port of K City of Korea was completely destroyed and the other(B) was seriously damaged to be demolished. Over-loaded snow and unexpected blast of wind were the causes of the accident and destructive behavior was brittle fracture caused by web local buckling and lateral torsional buckling at the flange below rafter. However, the architectural design technology of today based on material non-linear method does not consider the tolerances to solve the problem of such brittle fracture. So, geometric non-linear evaluation which includes initial deformation, width-thickness ratio, web stiffener and unbraced length is required. This study evaluates the structural safety of 4 models in terms of width-thickness ratio and unbraced length using ANSYS 9.0 with parameters such as width-thickness ratio of web, existence/non-existence of stiffener and unbraced length. The purpose of this study is to analyze destructive mechanism of the above-mentioned two warehouse buildings and to provide ways to promote the safety of pre-engineered buildings.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.329-332
• /
• 2005

Cross rolling process is one of incremental forming processes to form an axi-symmetric shaped metal component. It can be classified into two types according to the shape of dies, which are a drum type (roll type) and a plate type (straight type). It can also be classified into a wedge type and a ramp type processes according to deformation characteristics of a material. The ramp type die is applied to plate type cross rolling process in cold forming process for forming of teeth of gear or bolt, while the wedge type die is generally utilized to drum type and plate type cross rolling processes in hot forming process. A shape of the ramp type die is usually same as final shape of a product at every section of a progressing direction, while the shape of the wedge type die has different shapes in a progressing direction. In this paper, a rolling of neck part in a ball stud component has been carried out using the plate type cross rolling process with a ramp shaped die. Forming characteristics have been performed using finite element analysis in order to obtain a proper preform for the ramp type plate cross rolling process.

• Steel and Composite Structures
• /
• 제29권4호
• /
• pp.483-491
• /
• 2018

Timoshenko beam model is widely exploited in the literature to examine the mechanical behavior of stubby beam-like components. Timoshenko beam theory is well-known to require the shear correction factor in order to recognize the nonuniform shear distribution at a section. While a variety of shear correction factors are appeared in the literature so far, there is still no consensus on the most appropriate form of the shear correction factor. The Saint-Venant's flexure problem is first revisited in the frame work of the classical theory of elasticity and a highly accurate approximate closed-form solution is presented employing the extended Kantorovich method. The resulted approximate solution for the elasticity field is then employed to introduce two shear correction factors consistent with the Cowper's and energy approaches. The mathematical form of the proposed shear correction factors are then simplified and compared with the results available in the literature over an extended range of Poisson's and aspect ratios. The proposed shear correction factors do not exhibit implausible issue of negative values and do not result in numerical instabilities too. Based on the comprehensive discussion on the shear correction factors, a piecewise definition of shear correction factor is introduced for rectangular cross-sections having excellent agreement with the numerical results in the literature for both shallow and deep cross-sections.

• Steel and Composite Structures
• /
• 제48권4호
• /
• pp.443-459
• /
• 2023

This paper investigates the stability of a bi-directional functionally graded (BD-FG) cylindrical beam made of imperfect concrete, taking into account size-dependency and the effect of geometry on its stability behavior. Both buckling and dynamic behavior are analyzed using the modified coupled stress theory and the classical beam theory. The BD-FG structure is created by using porosity-dependent FG concrete, with changing porosity voids and material distributions along the pipe radius, as well as uniform and nonuniform radius functions that vary along the beam length. Energy principles are used to generate partial differential equations (PDE) for stability analysis, which are then solved numerically. This study sheds light on the complex behavior of BD-FG structures, and the results can be useful for the design of stable cylindrical microstructures.

• Nuclear Engineering and Technology
• /
• 제56권4호
• /
• pp.1244-1249
• /
• 2024

A combination of flow-accelerated corrosion (FAC) tests and corresponding computational fluid dynamics (CFD) tests were performed to determine the hydrodynamic parameters that could help predict the highly susceptible location to FAC in the elbow section. The accelerated FAC tests were performed on a specimen containing elbow sections fabricated using commercial 2-inch carbon steel pipe. The tests were conducted at flow rates of 9 m/s under the following conditions: water temperature of 150 ℃, dissolved oxygen <5 ppb, and pH 7. Thickness reduction of the specimen pipe due to FAC was measured using ultrasonic testing. CFD was conducted on the FAC test specimen, and the turbulence intensity, and shear stress were analyzed. Notably, the location of the maximum hydrodynamic parameters, that is, the wall shear stress and turbulent intensity, is also the same location with maximum FAC rate. Therefore, the shear stress and turbulence intensity can be used as hydrodynamic parameters that help predict the FAC-induced wall-thinning rate. The results provide a method to identify locations susceptible to FAC and can be useful for determining inspection priority in piping systems.

• 한국강구조학회 논문집
• /
• 제27권6호
• /
• pp.513-523
• /
• 2015

H형강 철골 모멘트 골조에서는 기둥의 강축 방향 용접 모멘트접합부를 활용하는 것이 구조적으로 가장 이상적이다. 하지만, 모멘트 골조가 직교하는 경우, 기둥의 약축 방향으로도 용접 모멘트접합부를 사용해야 한다. 국내에서는 특히 강축 및 약축 방향 모두를 용접 모멘트접합부를 자주 사용하는 관행이 있다. 대표적인 연성내진상세인 RBS(reduced beam section, 보단면감소)접합부의 경우 국내외적으로 강축접합 위주로 실험연구가 진행되어 약축 RBS 용접모멘트접합부에 대한 실험자료가 매우 희소하다. 본 연구에서는 RBS를 도입한 약축 용접 모멘트접합부의 내진성능을 실험적으로 고찰하였다. Gilton-Uang (2002)의 선행연구를 참고하여 보 플랜지는 연속판과 맞댐용접하고 웨브는 전단이음판과 C-형 필릿용접부로 설계하여 실험을 수행하였다. 보에 사용된 강재가 내진용 강재가 아닌 일반 SS400 강재임에도 불구하고 3% 이상의 소성회전각을 발휘하였다. 제한된 결과이긴 하지만, 전단이음판과 보 웨브 사이의 C-형 필릿용접부 설계에서 보 웨브에 작용하는 휨모멘트와 전단력의 편심의 영향을 구체적으로 고찰할 필요가 있는 것으로 판단된다. 본 실험결과를 토대로 전단이음판 부근의 보 웨브 파단을 방지할 수 있는 C-형 필릿용접 형상 및 설계방안을 제안하였다. 보 플랜지와 연속판의 완전용입 용접부는 맞댄이음(butt joint) 형식이 되어 국부좌굴에 취약하고 이로 인해 피로파괴가 발생하는 경향이 있으므로 용접작업에 지장이 없는 범위에서 용접접근공(스켈럽)의 크기를 최소화할 필요가 있다. RBS형상, 스틱아웃, 트림, 연속판 두께 증가 등과 같이 이미 검증된 약축 모멘트 용접접합부의 내진상세들은 따르는 것이 바람직하다.

• 한국강구조학회 논문집
• /
• 제27권5호
• /
• pp.471-481
• /
• 2015

모듈러 건축은 사전에 설계 검토된 건물 요소를 공장에서 모듈로 제작하여 현장으로 운송 조립하는 프리패브 건축 시스템이다. 모듈러 건축물의 구조 형식은 공법, 재료, 부재 구성 등에 따라 다양하게 구분될 수 있지만 사용되는 모듈의 구조 형식은 크게 벽식과 가구식으로 나눌 수 있다. 벽식 모듈은 모듈의 입면을 패널을 이용하여 구성하여 수직하중과 수평하중을 전달시키는 방식이다. 가구식 모듈은 기둥과 보를 이용하여 모듈을 구성하고, 용도에 맞춰 입면을 마감하거나 개방시켜 놓는 방식이다. 이 두 가지 모듈 방식은 국내에도 사용된 바 있으나 최근 가구식 모듈이 보편화되고 있다. 가구식 모듈의 기둥 부재로 각형강관이 일반적으로 사용되고 있으며, 보 부재로 C형강 또는 H형강이 사용되고 있다. 각형강관이 기둥 부재로 사용된 가구식 모듈간 접합을 위해 각형강관 기둥 단부에 고력볼트를 채우기 위해 액세스 홀을 가공하는 경우가 있다. 액세스 홀은 볼트체결을 위해 사람의 손이나 공구가 폐쇄형 단면인 각형강관 내부에 접근하기 위한 개구부로 액세스 홀은 기둥-보 접합부의 거동에 영향을 미치는 패널존을 약화시킬 가능성이 높다. 이 연구에서는 가구식 모듈의 기둥-보 접합부 거동에 영향을 미치는 액세스 홀, 기둥 두께, 다이아프램을 변수로 5개의 실험체를 제작하여 실험을 실시하였고 그 결과를 분석하여 제시하였다.

• Earthquakes and Structures
• /
• 제12권6호
• /
• pp.603-617
• /
• 2017

This paper presents investigation into the behavior of beam-column joints, with the joint region concrete being replaced by steel fiber reinforced concrete (SFRC) and by ultra-high performance concrete (UHPC). A total of ten beam-column joint specimens (BCJ) were tested experimentally to failure under monotonic and cyclic loading, with the beam section being subjected to flexural loading and the column to combined flexural and axial loading. The joint region essentially transferred shear and axial stresses as received from the column. Steel fiber reinforced concrete (SFRC) and ultra-high performance concrete (UHPC) were used as an innovative construction and/or strengthening scheme for some of the BCJ specimens. The reinforced concrete specimens were reinforced with longitudinal steel rebar, 18 mm, and some specimens were reinforced with an additional two ties in the joint region. The results showed that using SFRC and UHPC as a replacement concrete for the BCJ improved the joint shear strength and the load carrying capacity of the hybrid specimens. The mode of failure was also converted from a non-desirable joint shear failure to a preferred beam flexural failure. The effect of the ties in the SFRC and UHPC joint regions could not be observed due to the beam flexural failure. Several models were used in estimating the joint shear strength for different BCJ specimens. The results showed that the existing models yielded wide-ranging values. A new concept to take into account the influence of column axial load on the shear strength of beam-column joints is also presented, which demonstrates that the recommended values for concrete tensile strength for determination of joint shear strength need to be amended for joints subject to moderate to high axial loads. Furthermore, finite element model (FEM) simulation to predict the behaviour of the hybrid BCJ specimens was also carried out in an ABAQUS environment. The result of the FEM modelling showed good agreement with experimental results.

• 한국수산과학회지
• /
• 제18권1호
• /
• pp.8-14
• /
• 1985

어구의 모형실험을 위한 회유수조를 제작하여 시험한 결과를 요약하면 다음과 같다. 1. 동력 50 H.P.의 D.C. Motor에 의하여 생기는 최대 유속은 약 2.3m/sec로서 지시전압 200 V, 지시전류 185 A에서 나타났다. 2. 유속과 전압과의 관계는 $0{\sim}1.0m/sec$까지는 비선형적으로 비례하나 1.0m/sec 이상에서 직선적으로 비례하였다. 3. 공칭 유속의 범위는 0.4m/sec에서 1.8m/sec까지이다. 그 이상으로 부터 최대 2.3m/sec까지는 수십분 이상 사용하며 모터의 과열현상이 나타났다 4. 수유 횡단면을 따르는 수직 유속분포는 수로중앙을 중심으로 좌우 약 70 cm까지는 0.2m/sec 이내의 차이를 나타냈다. 그러나 그 외부는 프로펠러의 크기, 벽과의 마찰로 인하여 급격히 감소한다. 5. 수심 중앙면을 따르는 수평적 유속 분포를 보면 유입부로 부터 관측부의 중앙까지는 수류변화가 거의 없으나 그 이후는 수로의 만곡에 따라 편향되었다.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.331-337
• /
• 2010

This study compared the macro and micro electrochemical characteristics at the local area of welding metal on dissimilar welding parts for type 304 stainless steel (SS) and type 316L SS. The materials are used for double wall gas pipe of duel fuel engine for a ship. The various potentiodynamic experiments were performed several times in 10% ${H_2C_2O_2}{\cdot}{H_2O}$ solution using macro and micro methods, respectively. The micro electrochemical experiments conducted to resolve at local area on cross-section of dissimilar welding materials by micro-droplet cell device. The micro-droplet cell techniques can be used almost electrochemical experiments to resolve corrosion characteristics of the limited electrode area of the metallic surface between wetted spot of working electrode and tip of sharpened capillary tube. The results of macro electrochemical experiments show that resistance of active dissolution reaction at welding zone was high due to low current density by formation of passivation protection film at passive region. According to the micro electrochemical experiment, the corrosion current density of welding zone and bond zone were relatively high.