• Steel and Composite Structures
• /
• 제27권3호
• /
• pp.337-353
• /
• 2018

In previous weak-axis moment connection tests, brittle fracture always initiated near the edge of the beam flange groove weld due to force flow towards the stiffer column flanges, which is the opposite pattern as strong-axis moment connections. As part of the China NSFC (51278061) study, this paper tested two full-scale novel weak-axis reduced beam section moment connections, including one exterior frame connection specimen SJ-1 under beam end monotonic loading and one interior frame joint specimen SJ-2 under column top cyclic loading. Test results showed that these two specimens were able to satisfy the demands of FEMA-267 (1995) or ANSI/AISC 341-10 (2010) without experiencing brittle fracture. A parametric analysis using the finite element software ABAQUS was carried out to better understand the cyclic performance of the novel weak-axis reduced beam section moment connections, and the influence of the distance between skin plate and reduced beam section, a, the length of the reduced beam section, b, and the cutting depth of the reduced beam section, c, on the cyclic performance was analyzed. It was found that increasing three parametric values reasonably is beneficial to forming beam plastic hinges, and increasing the parameter a is conducive to reducing stress concentration of beam flange groove welds while increasing the parameters b and c can only reduce the peak stress of beam flange groove welds. The rules recommended by FEMA350 (2000) are suitable for designing the proposed weak-axis RBS moment connection, and a proven calculation formulation is given to determine the thickness of skin plate, the key components in the proposed weak-axis connections. Based on the experimental and numerical results, a design procedure for the proposed weak-axis RBS moment connections was developed.

• 소성∙가공
• /
• 제22권8호
• /
• pp.477-485
• /
• 2013

This paper aims to evaluate quantitatively the springback characteristics that evolve in the sheet metal forming of an S-rail in order to understand the reasons of shape inaccuracy and to find a remedy. The geometrical springback is classified into six modes: angle change of punch and die shoulders, wall curl, ridge curl, section twist, and axial twist. The measuring method for each springback mode is suggested and quantitative measurements were made to determine the tendency towards shape accuracy. Forming experiments were conducted with four types of steel sheets that have different tensile strengths, which were 340MPa, 440MPa, 590MPa and 780MPa, in order to evaluate the effect of the tensile strength and the bead shape on the springback behavior. Springback tendencies show that they are greatly affected by the tensile strength of the sheet and the shape of the tools. Almost all springback modes except the section twist and the axial twist show a linearly increasing trend as the tensile strength of the sheet increases. The results can be used as basic data for design and for compensation of the press die geometry when forming high strength steels which exhibit large amounts of springback.

• Computers and Concrete
• /
• 제2권4호
• /
• pp.309-324
• /
• 2005

The moment-curvature relationship of reinforced concrete beams made of normal- and high-strength concrete experiencing complex load history is studied using a numerical method that employs the actual stress-strain curves of the constitutive materials and takes into account the stress-path dependence of the concrete and steel reinforcement. The load history considered includes loading, unloading and reloading. From the results obtained, it is found that the complete moment-curvature relationship, which is also path-dependent, is similar to the material stress-strain relationship with stress-path dependence. However, the unloading part of the moment-curvature relationship of the beam section is elastic but not perfectly linear, although the unloading of both concrete and steel is assumed to be linearly elastic. It is also observed that when unloading happens, the variation of neutral axis depth has different trends for under- and over-reinforced sections. Moreover, even when the section is fully unloaded, there are still residual curvature and stress in the section in some circumstances. Various issues related to the post-peak behavior of reinforced concrete beams are also discussed.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.109-116
• /
• 2000

The objective of this study is to measure rim surface adhesion and to calculate motion resistance produced by the adhesion acting on the rim section of a circular wheel under sticky soil condition. The mechanisms of generating motion resistance by the adhesion on a circular wheel were analyzed through wheel motion. Experiments were conducted in an indoor soil bin that contains loam soil. A circular steel wheel was used for experiments. A part of the wheel rim was cut off, and transducers which can measure normal and tangential forces were installed in this section. Calculated motion resistance at a part of the rim section was superposed for one wheel rotation as motion resistance produced by the rim surface adhesion. The motion resistance increased with increasing the dynamic load. Ratio of the motion resistance to total motion resistance measured by an axis transducer was about 23 to 46 % in this study.

• Steel and Composite Structures
• /
• 제18권5호
• /
• pp.1177-1195
• /
• 2015

Six specimens are tested to investigate the cyclic behavior of beam-to-column abnormal joints in steel moment-resisting frames, which are designed according to the principle of strong-member and weak-panel zone. Key parameters include the axial compression ratio of column and the section depth ratio of beams. Experimental results indicate that four types of failure patterns occurred during the loading process. The $P-{\Delta}$ hysteretic loops are stable and plentiful, but have different changing tendency at the positive and negative direction in the later of loading process due to mechanical behaviors of specimens. The ultimate strength tends to increase with the decrease of the section depth ratio of beams, but it is not apparent relationship to the axial compression ratio of column, which is less than 0.5. The top panel zone has good deformation capacity and the shear rotation can reach to 0.04 rad. The top panel zone and the bottom panel zone don't work as a whole. Based on the experimental results, the equation for shear strength of the abnormal joint panel zone is established by considering the restriction of the bottom panel zone to the top panel zone, which is suitable for the abnormal joint of H-shaped or box column and beams with different depths.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.149-152
• /
• 2006

Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.

• Steel and Composite Structures
• /
• 제17권1호
• /
• pp.83-103
• /
• 2014

The objective of this research is to study the ultimate moment capacity of the connections between steel I-beams and concrete-filled steel tube columns using different stiffener configurations. The main parameters considered are column cross section shape, square or circular, and filling the column with concrete. This analytical study includes finite element models using ANSYS program taking geometric and material nonlinearities into consideration. These models are verified against the experimental results obtained from previous researches and current design guides. The results show that using proper stiffener configuration affects the stress distribution through the connection and increases the ultimate moment capacity of the connections. Also, circular column is advantageous than the square column for all stiffener configurations and dimensions.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.240-248
• /
• 2004

Recently, the customer's demands for automotive steel sheet have been diversified and sterned more. Therefore, as the tendency of auto industry light-weight, one among these requirements is the trend for high strength together with the thinness of automotive steel sheet. Because Mn added essentially in producing high strength steel sheet is bonded strongly with oxygen, the Fine oxidation layer was created at the welding face after the flash butt welding operated in entry section of pickling line. Thereby it was caused the crack or breakage of welding part in process of cold rolling. At this research, in order to protect the contact Mn with oxygen in atomosphere it was considered to fire oxygen with LNG and the related researches have been gone forward with the find out concrete and to apply them to operation.

• Earthquakes and Structures
• /
• 제20권4호
• /
• pp.417-430
• /
• 2021

Due to functional requirements, SRC column-RC beam abnormal joints with characteristics of strong beam weak column, variable column section, unequal beam height and staggered height exist in the Steel reinforced concrete (SRC) frame-bent main building structure of thermal power plant (TPP). This paper presents the experimental results of these abnormal joints through cyclic loading tests on five specimens with scaling factor of 1/5. The staggered height and whether adding H-shaped steel in beam or not were changing parameters of specimens. The failure patterns, bearing capacity, energy dissipation and ductile performance were analyzed. In addition, the stress mechanism of the abnormal joint was discussed based on the diagonal strut model. The research results showed that the abnormal exterior joints occurred shear failure and column end hinge flexural failure; reducing beam height through adding H-shaped steel in the beam of abnormal exterior joint could improve the crack resistance and ductility; the abnormal interior joints with different staggered heights occurred column ends flexural failure; the joint with larger staggered height had the higher bearing capacity and stiffness, but lower ductility. The concrete compression strut mechanism is still applicable to the abnormal joints in TPP, but it is affected by the abnormal characteristics.

• 한국강구조학회 논문집
• /
• 제24권1호
• /
• pp.23-34
• /
• 2012

본 연구에서는 인장강도 800MPa급 고강도강재(HSA800)의 단주 중심압축실험과 편심압축실험을 통해 균등압축과 휨-압축 부재의 강도를 평가하여 현행 강구조기준(KBC2009, AISC2005)의 적용성 여부를 검토하였다. 또한 잔류응력의 계측을 통하여 강재 항복강도와 잔류응력과의 상관성 여부도 검토하였다. 고강도강재와 일반강재의 국부좌굴 거동 차이의 여부를 확인하기 위하여 중심압축실험에 SM490 강재로 제작된 비교실험체도 포함시켰다. 강도로 무차원화한 판폭두께비와 판 단부의 지지조건을 주요변수로 하여 실험을 실시하였다. 편심압축실험은 HSA800 강재만을 대상으로 하였으며, 휨-압축의 조합력을 받는 부재의 P-M 상관관계를 알아보기 위해 가력 편심거리를 조정하여 다양한 P-M 조합에 대해 강도평가 실험을 수행하였다. 잔류응력은 중심압축실험에 사용된 H형단면 실험체를 대상으로 비파괴실험법인 압입법에 의해 가력 이전에 그 크기와 분포를 측정하였다. 실험결과 중심압축을 받는 모든 HSA800 단주는 판 단부의 지지조건 및 판폭두께비 조건에 따른 현행 강구조기준의 설계강도를 충분히 발휘하였다. 편심압축을 받는 실험체 역시 현행 설계기준의 P-M 상관관계를 충분히 안전측으로 충족하였다. 본 연구에서도 잔류응력의 크기는 강재의 항복강도와 무관하다는 선행연구결과와 합치하는 잔류응력 측정값이 얻어졌다.