• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.372-377
• /
• 2020

This paper is based on the triangular inset patch antenna as the basic structure, and the array structure is the twin tree form to improve the antenna's main lobe gain and reduce the side lobe gain. A twin tree structure was implemented by placing two identical trees of 2-4-6 arrays of triangular inset patches side by side. The parametric analysis confirmed that the gap between tree structures arranged side by side is most effective for impedance matching. The fabricated antenna has a gain of 16.74 dBi at 24.15 GHz, and the beam width of the main lobe is 22° in the E-plane and 6° in the H-plane. The antenna size was 125 mm × 50 mm, and a Taconic TLC substrate with a dielectric constant of 3.2 was used. Although the main lobe gain is improved over the twin tree structure, The directivity in the beam pattern due to the mutual interference of the two tree array structure can be improved.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.4
• /
• pp.345-354
• /
• 2010

This paper presents an experimental investigation of the structural performance of a large-span girder bridge with an under-tension system. Typical long-span structures with beam and girder members have greater structural member depths and sizes to carry the moment and deflection. An under-tension system can be an effective structural system, as it allows the cables to resist some portions of the vertical loadings and deflections. To evaluate the serviceability and ultimate strength of the under-tension system, two $10m{\times}2.4m$ experimental under-tension systems were built and tested. One was developed with an H-beam section, and the other was made with a PF500 section that had the advantages of fast construction and lower construction cost. In the test, the maximum deflections at the mid-point of both beams were effectively reduced using under-tension systems. Also, the increased tension forces in the cable reduced the deflections. The PF500 members, which had a new shape and were developed using the module systems, performed better than the typical H-beam sections in terms of the deflections and ultimate strength.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10A
• /
• pp.1050-1056
• /
• 2007

In order to set up a steel frame at every construction site, it is necessary to attach a shackle to a crane to move steel frame beams and columns(H beams). The shackle used for this purpose must be removed manually from a higher place, which causes the risk of safety accidents to increase, work efficiency to decrease, and construction costs to rise. In this study, micro-mini, super lightweight, lower power consumptive, and cheaper auto-shackle with two-way RF communication, which can be used practically at construction site is designed and developed. The developed auto-shackle is able to have excellent remote monitoring and controlling functions, by adopting new operating principles and structures different from the existing one. The results of the study reveal that the auto-shackle can be applied for the purpose of remote controlling of various construction equipments and speed up the advancement of construction equipments.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.1
• /
• pp.75-78
• /
• 2002

Thirty three layer $TiO_2/SiO_2$ coating mirrors with high reflectance through a 620~820nm wavelength range have been designed and fabricated by electron beam evaporation method. Multilayer films were deposited on glass(BK7) and sequentially. The high reflector design is based on alternating high and low refractive index layers. $n_H$ and $n_L$ such that a "stopband"(or area of high reflectivity) is created that is centered around the design wavelength. ${\lambda}_0$. The measured transmittance spectrum with an incident wavelength at an incident angle of $40^{\circ}{\pm}7^{\circ}$ exhibited a reflectance of 99.9% at the wavelength of 620~820nm but high peak transmittance in the wavelength region from 700 to 740nm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.5
• /
• pp.550-555
• /
• 2007

The effective fracture toughness testing of materials intended for application in Micro Electro Mechanical Systems (MEMS) devices is required in order to improve understanding of how micro sized material used in device may be expected to perform upon the micro scale. ${\gamma}$-TiAl based materials are being considered for application in MEMS devices at elevated temperatures. Especially, in Alloy 4, both ${\alpha}_2$ and ${\gamma}$ lamellae were altered markedly in 3,000 h, $700^{\circ}C$ exposure. Parallel decomposition of coarse ${\alpha}_2$ into bunches of very fine (${\alpha}_2+{\gamma}$) lamellae. Parallel decomposition of coarse ${\alpha}_2$ into bunches of very fine (${\alpha}_2+{\gamma}$) lamellae. The materials were examined 2 types Alloy 4 on heat exposed specimen($700^{\circ}C$, 3,000 h) and no heat exposed one. Micro sized cantilever beams were prepared mechanical polishing on both side at $25{\sim}30{\mu}m$ and electro final stage polishing to observe lamellar orientation of same colony with EBSD (Electron Backscatter Diffraction Pattern). Through lamellar orientation as inter-lamellae or trans-lamellae, Cantilever beam was fabricated with Focused Ion Beam(FIB). The directional behavior of the lamellar structure was important property in single material, because of the effects of the different processing method and variations in properties according to lamellar orientation. In MEMS application, it is first necessary to have a reliable understanding of the manufacturing methods to be used to produce micro structure.

• Laser Solutions
• /
• v.9 no.2
• /
• pp.23-30
• /
• 2006

Silicon Nitride $(Si_3N_4)$, which is widely used in a variety of applications, is hard-to-machine due to its high hardness. At high temperature (e.g. above $1000^{\circ}C)$, however, the machinability can be greatly improved. In this work, we used a $CO_2$ laser with a high absorptivity to $Si_3N_4$ of 0.9 to locally heat the surface of a rotating $Si_3N_4$ rod on a lathe. In order to examine the effects of the laser-assisted heating on hardness, an $Si_3N_4$ rod is heated to temperatures from 900 to $1800^{\circ}C$ and is rotated at speeds from 440-900 rpm in experiments. When the rod is naturally cooled to room temperature, we measured the Vickers hardness (Hv); and observed the surface of HAZ using a scanning electron microscopy (SEM). Energy dispersive spectroscopy (EDS) was used for ingredient analysis. Results showed that when heated at $1600^{\circ}C$, the hardness of $Si_3N_4$ decreased from 1500 Hv to 1000 Hv. Also, in order to predict the depth of HAZ, we numerically analyzed the laser-assisted heating of $Si_3N_4$.

• Journal of the Korean Ceramic Society
• /
• v.43 no.5 s.288
• /
• pp.299-303
• /
• 2006

In this paper, anode supported SOFC with columnar structured YSZ electrolyte was fabricated via Electron Beam Physical Vapor Deposition (EBPVD) method. Liquid condensation process was employed for the preparation of NiO-YSZ substrate and the high power electron beam deposition method was used for the deposition of YSZ electrolyte film. Double layered cathode with LSM-YSZ and LSM was printed on electrolyte via screen-printing method and fired at $1150^{\circ}C$ in air atmosphere for 3 h. The electrochemical performance and the long-term stability of $5{\times}5cm^2$ single cell were investigated with DC current-voltage characteristics and AC-impedance spectroscopy. According to the investigation, $5{\times}5cm^2$ sized unit cell showed the maximum power density of around $0.76W/cm^2$ at $800^{\circ}C$ and maintained the stable performance over 400 h.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.187-193
• /
• 2005

The photocatalyst $TiO_2$ thin film was made from titanium (IV) isopropoxide, ethanol, and HCl by sol-gel method. The surface observation by SEM showed the sample that was coated 5 times at $500^{\circ}C$ had good properties. The component ratio, in atom% of O : Ti by EDX analysis, of 61 : 39 by spin coating was superior than dip coating. It was found that crystal structure changed from anatase phase to rutile phase as a function of the temperature of thin film fabrication, and this was measured by XRD. The photolysis efficiency of total organic compounds (TOC) by lighting UV beam on $TiO_2$ thin film showed 20%~65% within 1 h, and decreased slowly thereafter.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.93-97
• /
• 2012

Heat treatment effect of polyethylene (PE) separators was investigated after storage at 80, 100 and $120^{\circ}C$ for 1 h. All the samples showed enhanced tensile strength and modulus after heat treatment, but thermal shrinkage up to 15% was observed in PE films having newly formed dimple structure on the surface of fiber after annealed at 100 and $120^{\circ}C$. Although there was 5% of thermal shrinkage after annealing at $80^{\circ}C$, no such serious changes in PE fiber was observed. Furthermore, the separator was found to have enhanced cell performance with 1.3 and 2.3 times higher tensile strength and modulus after heat treatment at $80^{\circ}C$ for 1 h.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.70-75
• /
• 1997

An improved technique based upon an electron beam evaporation system has been developed to prepare cubic thin films In crystalline semiconductors. Zinc blonde CdSe epilayers were grown on GaAs(100) substrate by an e-beam evaporation method. The lattice parameter obtained from (400) reflection is $6.077\AA$, which is in excellent agreement with the value reported in the literature for zinc blonde CdSe. The orientation of the as-grown CdSe epilayer is determined by electron channeling patterns. The crystallinity of epitaxial CdSe layers were investigated on the double crystal X-ray rocking curve. The carrier concentration and mobility of epilayers deduced by Hall effect measurement are about $10^{18}{\textrm}{cm}^{-3}$, $10^2\textrm{cm}^2/V{\cdot}sec$ at room temperature, respectively. The photocurrent spectrum peak of the epilayer at 30 K exhibits a sharp change at 1.746 eV due to the free exciton of cubic CdSe.