• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2000년도 추계학술대회 논문집
• /
• pp.419-420
• /
• 2000

The present study introduces and describes the characteristics of the spiral guide and groove body cyclones for the first time. The spiral guide was set inside the cyclone body or the inside of the cyclone body was grooved circumferentially or vertically. Except for the cyclone body, all configurations were the same. The particle collection efficiency for a conventional cyclone (Figure 1) was measured under a series of flow rates ranging from 15 L/min up to 80 L/min, and was compared with that yielded using existing theories. (omitted)

• 대한기계학회논문집A
• /
• 제30권8호
• /
• pp.957-964
• /
• 2006

As the requirement of LCD products which are large screen and have high brightness increases, the role of light guide panel (LGP) of which micro-features diffuse the light uniformly on surface is getting important. In general, there are many errors in machining like machine tool errors process error, setup error and etc. The amount of setup error in general machining is not so big in comparison with the others, so it is mostly neglected. But, especially in v-groove micromachining, setup error has a significant effect on micro-features. Low quality product and high cost are resulted from setup error. In v-groove micromachining, to confirm the effect of setup error, it is identified and then setup error synthesis model is derived from analysis of tool and workpiece setup. In addition, to predict the micro-features affected by setup error and enhance the production efficiency, the setup condition satisfying the tolerance of micro-features is geometrically analyzed and presented.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.185-191
• /
• 2008

터빈 익렬 내에서 발생하는 2차유동은 터빈 익렬에서 전체 공기역학적 손실의 30$\sim$50%, 입구 스테이터에서는 약 20%를 차지하며 터빈 효율 향상에 있어 개선해야 될 중요한 부분으로 인식되고 있다. 본 논문에서는 블레이드 앞전에 모서리 홈을 만들어 홈의 높이 및 깊이 등의 형상 변수를 변화시켜가면서 말굽와류의 발생 영역 및 강도의 감쇄 특성 및 구조에 대해 상용코드인 $FLUENT^{TM}$를 이용하여 수치해석적인 방법으로 연구하였다.

• 반도체디스플레이기술학회지
• /
• 제18권2호
• /
• pp.6-10
• /
• 2019

In the presence of $\mu-tip$ for narrow stripe coating, there appears lateral capillary flow along the hydrophilic head lip because the $\mu-tip$ has some resistance to flow. It was known to be suppressed by increasing the contact angle of the head lip. In this paper, we have demonstrated by computational fluid dynamics(CFD) simulations that it can also be suppressed by the formation of micro-patterns on the shim and meniscus guide embedded into the slot-die head. To optimize the micro-patterned structure, we have performed simulations by varying the groove width, depth, and clearance. In the absence of micro-patterns, it is shown by experiment and simulation that the solution spreads to a distance of $1,300{\mu}m$ from the ${\mu}-tip$. In the presence of micro-patterns with the groove width and clearance of $50{\mu}m$, the distance the solution spreads is reduced to $260{\mu}m$. However, no further suppression in the capillary flow is observed with micro-patterns with the groove width of $40{\mu}m$ or less. It is also observed that the capillary flow is not affected by the groove depth if it is larger than $10{\mu}m$. We have shown that the distance the solution spreads can be reduced further to $204{\mu}m$ by coating a hydrophobic material (contact angle of $104^{\circ}$) on the surface of micro-patterns having the groove width and clearance of $50{\mu}m$.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.27-33
• /
• 2005

This study deals with the truing of diamond wheel fur the manufacture of micro v-shaped grooves with fine sharp edges in the grinding. Fine micro v-shaped grooves are key components to fabricate LGP(light guide plate), optical fiber connector and so on. Conventional v-shaped groove methods such as etching and lithography are difficult to make grooves with accuracy and cutting by lathe is difficult to select target materials. Therefore, as a preliminary stage to developing the grinding technology that will be expected fabrications for micro 3-dimensional structure of high effectivity and accuracy and freed up the restrictions of machinability to the materials for micro v-shaped grooves, truing is carried out with resin bond diamond wheel and electroforming diamond wheel using a cup-type truer. From the experimental results, it is found that the effects according to working direction of the cup-type truer and the restrainable methods of plastic deformation that is generated at wheel edge are examined. As a result, fine micro v-shaped diamond wheel was obtained, which are applicable to micro grinding for optical devices.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.97-100
• /
• 2004

In recent years, a demand for micro-structure machining is increasing by the development of information and optics industries. Micro machining technology is in general well known in the field of lithograghy. However, the requirement of producing micro machine and/or micro mechanism with metal materials will be increased since a variety of workpiece configurations can be easily made. In this paper, ultra precision machine is developed to obtain micro groove and mirror surface using single crystal diamond tool. According to the cutting experiment, no burr was found at the edge of V-grooves, and the surface roughness of copper is about 1～3nm Ra. It is verified that ultra precision machine is effective to high precision machining.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.147-150
• /
• 2002

A light guide panel is an element of the LCD backlight module that is often used for the display of compact electronic devices. In this study, a laser marking system is proposed to fabricate light guide panel, which can be replaced of other manufacturing methods such as silk printing, stamping, and v-cutting methods. The objectives of this research are the establishment of laser marking system, evaluation of laser marking parameters, understanding marking process, application to PMMA, reliability test and quality inspection. A 50W $CO_2$ laser (CW) was used to perform different experiments in which, the influence of some processing parameters (average power, scanning speed) on the geometry and quality of groove pattern was studied. The width of the etched grooves increases with increasing a laser power and decreasing a scan speed. In order to analyze surface characteristics and optical properties (luminance, uniformity), SEM photography and BM7 (luminance measuring system) were used. As a result, the optimal conditions of the process parameters were determined.

• 제어로봇시스템학회논문지
• /
• 제15권11호
• /
• pp.1076-1079
• /
• 2009

This article deals with an optical image stabilizer which moves an image sensor in the direction of cancelling the vibration caused by hand shaking to prevent a photographed image from blurring. The ball-guide way method adopted as a transfer device of the image sensor is easy to be manufactured because of its simple structure and is suitable to minimize the friction between mechanisms, but has weakness of a chance of physical defect such as groove and rising. In case that the movement of the transfer device equipped with the image sensor is blunted because a ball is stuck in defects of guide way, the performance of the image stabilizer falls down drastically. We propose a method to prevent the transfer device from blunting by applying artificial vibration. At this time, the artificial vibration should be designed under consideration of dynamic characteristics and specifications of the system to be discriminated from the vibration caused by hand shaking.

• Clinics in Shoulder and Elbow
• /
• 제3권1호
• /
• pp.54-60
• /
• 2000

As a surgical treatment of ulnar nerve entrapment syndrome includes simple decompression, medial epicondylectomy, and anterior transposition of the ulnar nerve into a subcutaneous or submuscular bed have been widely used. Despite many reports of these surgical procedure, there is little to guide the choice of one surgical technique. The purpose of our study is to analyse clinical and electrodiagnostic result after minimal invasive decompression by decompression and medial epicondyloplasty(deepening of ulnar groove). We have experienced 9 cases of ulnar nerve entrapment syndrome who were treated with decompression and medial epicondyloplasty. Male were five and female were four. The mean age at operation was 36 years ranging from 23 to 47 years. Operative procedure was to incise the medial intermuscular septum and aponeurotic arch of flexor carpiulnaris and to deepen the ulnar groove. Patients are allowed to do range of motion(ROM) exercise on the average 5days. All patient were relieved pain and improved motor and sensory function, and this procedure allows early ROM exercise after operation because the muscle have not been detached.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1597-1600
• /
• 2005

Recently, the trends of TFT-LCD are large scale and thin thickness, so, the demands of Light Guide Panel(LGP) which is able to substitute for prism sheets are appeared. Functions of LGP obtaining polarization of light of the prism sheet as well as the incidence and reflection of light are demanded. This prismless type LGP to complete functions of the existing LGP and polarization at once must be supported by micro machining technology of LGP surface. In this research, we have used the STAMPER method for the mass product and In-Line process, and the optimized conditions are established by analyzing the cutting force and conditions according to the material and processing properties when the prismless type LGP mold is fabricated. Parameters of the cutting condition were the workpiece and cutting depth.