• 한국인터넷방송통신학회논문지
• /
• 제19권6호
• /
• pp.65-71
• /
• 2019

기존의 대지저항률과 접지저항 현장 측정 방식은 일정한 간격의 측정전극을 설치하여 전류를 인가하여 대지의 저항값에 따른 전압강하를 측정하게 되는데 현장 대지의 층상 구조가 특이성을 갖게 되면 역산 시 경계 조건의 오차를 발생하게 되고 접지 설계 시 중요한 대지저항률 분석이 시뮬레이션 상과 많은 차이를 보이게 된다. 본 연구는 정보통신 융합환경에서 아두이노 모듈과 스마트 접지 측정 기술를 활용하여 대지의 층상이 특이성을 갖는 구조라도 신뢰할 수 있는 스마트 대지 저항 측정장치를 개발하여 대지저항을 분석하고 데이터를 축적하여 대지의 경년변화를 예측한다. 현장의 지형적인 특성을 고려하여 접지저항과 대지저항 측정 시 각도와 거리를 정확하게 위치시켜 보조전극을 설치할 수 있는 접지저항 측정장치 및 측정방법을 제안한다. 정확한 접지저항 값을 선정할 수 있게 하기 위해 설치된 전극을 통해 접지저항 값뿐만 아니라, 대지저항률을 취득할 수 있어 유사지역에 전기시설물 설치 시에 유용한 자료로 활용할 수 있다. 또한 신뢰성 높은 데이터를 활용하고 현장의 대지구조를 분석하여 공사비용 뿐 아니라 접지설계에서 중요한 비중을 차지하는 대지에 대한 정밀한 분석으로 전위상승 등의 접지설비설계에서 많은 활용이 기대된다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.77-81
• /
• 2000

The purpose of this paper is to describe a new measuring method of ground resistance for the grounding system in energized power equipment and substations. It is very difficult to measure the accurate ground resistance in energized power equipment and substations because of the noise conducted from all external connections to the grounding system and harmonics components caused by unbalanced loads and overloads. The ground resistance that is measured with existing methods includes not only the effect of desired signals but also noise components for the measurement period in grounding system. The measured value of ground resistance can entirely be different from actual value. In this paper, to eliminate 60[Hz] power system interference and harmonic components the low-pass filter method was used in the measurement of ground resistance.

• 조명전기설비학회논문지
• /
• 제16권4호
• /
• pp.117-123
• /
• 2002

접지저항의 측정은 접지계통의 접지성능이 적정한가를 평가하기 위한 가장 기본적이고 중요한 작업이라고 할 수 있다. 그러나 실제 현장에서, 특히 접지극의 크기가 큰 경우일수록 접지저항을 정확히 측정하기란 쉽지 않은데, 이는 정확한 접지전위 측정을 위한 기준전위 점을 찾기가 힘들기 때문이다. 본 논문에서는 접지극 주변에서 측정한 지표면전위를 분석하여 기준전위 점의 위치를 정확히 식별하는 방법과 그 정당성을 제시하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1240-1249
• /
• 2008

Jacket anchor was developed to increase the pullout resistance of general ground anchor in soft ground, and the mechanism of pullout resistance of jacket anchor was analyzed. Also, the ultimate bond stress of jacket anchor was estimated by ultimate resistance which is determined by field tests. Grout milk was injected into the jacket to make grout bulb of jacket anchor. The formation of grout bulb of jacket anchor increases the diameter of grout bulb, ground strength and confining pressure between anchor grout and soil. From the twelve field test results, it was observed that the pullout resistance of jacket anchor is 15.38~295.02%(average 83.53%) greater than that of general ground anchor, and plastic deformation of jacket anchor is 20.78~1,496.45%(average 288.78%) smaller than that of general ground anchor at the same load cycle. Especially, it was investigated that the increase of ultimate resistance over 200% and the reduction of plastic deformation over 600% was obtained in gravel layer. It means that the jacket anchor is superior to the general ground anchor in gravel layer. Finally, the ultimate bond stress was proposed to design jacket anchor.

• 한국지반신소재학회논문집
• /
• 제22권4호
• /
• pp.27-34
• /
• 2023

본 연구에서는 말뚝에 작용하는 구속압과 지반의 세립분 함유율을 고려한 말뚝 인발실험을 실시하였다. 그리고 실험 결과를 이용하여 말뚝의 인발저항에 미치는 지중 구속압의 영향을 분석하여 인발저항정수를 고찰하였다. 인발실험 결과, 모형지반의 세립분 함유율과 구속압의 크기에 관계없이 약 7mm~9mm의 인발변위에서 최대인발저항력이 발생되었다. 말뚝의 최대인발저항력은 모형지반의 세립분 함유율이 증가할수록 감소하였고, 이러한 경향은 구속압이 클수록 현격하게 나타났다. 말뚝인발실험 결과의 신뢰성을 검토하기 위해 인발저항력을 이론식으로 산정해 실험결과와 비교한 결과, 모든 구속압 조건에서 세립분 함유율 증가에 따라 실험값과 이론값 모두 동일하게 인발저항력이 감소하는 경향을 보였다. 인발저항정수에 대한 분석 결과, 말뚝과 지반의 경계에서 발생하는 인발저항력에 있어서 주변 지반의 세립분 함유율이 증가할수록 경계면 마찰각보다 부착력의 영향이 커지는 것을 확인하였다.

• 조명전기설비학회논문지
• /
• 제24권10호
• /
• pp.85-89
• /
• 2010

During a ground fault the maximum fault current and neutral to ground voltage will appear at the pole nearest to the fault. Distribution lines are consisted of three phase conductors, an overhead ground wire and a multi-grounded neutral line. In this paper phase to neutral faults were staged at the specified concrete pole along the distribution line and measured the ground fault current distribution in the ground fault current, three poles nearest to the fault point, overhead ground wire and neutral line. A effect by grounding resistance of poles of ground fault current in the 22.9[kV] multi-ground distribution system. by field tests.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.288-292
• /
• 2006

Usually, equations that calculate ground resistance of earth electrode was already informed well by form of earth electrode. But, when apply on the spot because general expressions are very insufficient at point that calculate exact ground resistance value by variation of earth electrode, and constant value that corrective coefficient for ground resistance calculation is fixed regardless of change of the earth resistivity specially is presented, it is actuality that difficulty is. Therefore, in this study, about these problem, proposed corrective coefficient for calculation of ground resistance according to change of the earth resistivity.

• 설비공학논문집
• /
• 제23권2호
• /
• pp.95-102
• /
• 2011

A ground loop heat exchanger in a ground source heat pump system is an important unit that determines the thermal performance of a system and its initial cost. A proper design requires certain site specific parameters, most importantly the ground effective thermal conductivity, the borehole thermal resistance and the undisturbed ground temperature. This study was performed to investigate the effect of some parameters such as borehole lengths, various grouting materials and U tube configurations on ground effective thermal conductivity and borehole thermal resistance. In this study, thermal response tests were conducted using a testing device to 9 different ground loop heat exchangers. From the experimental results, the length of ground loop heat exchanger affects to the effective thermal conductivity. The results of this experiment shows that higher thermal conductivity of grouting materials leads to the increase effective thermal conductivity from 22 to 32%. Also, mounting spacers have increased by 14%.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1366-1369
• /
• 2010

Along with the increasing need of sea development, the hydraulic stability of seabed structure on a soft seafloor ground is becoming an issue in the course of seaside development recently. However, the movement and hydraulic resistance or hydraulic stability of seafloor ground are mutually coupled with various phenomena, and there has been no clear proof for the issue, which makes it difficult to forecast. Furthermore, most researches are focused on hydraulic variables and the conditions of marine external force, while there have been few researches into the assessment in consideration of the type of a seafloor ground and the geotechnical characteristics. In addition, according to the periodic change of the flow direction, possible changes in hydraulic resistance performance of the seafloor deserves all the recognition. But there is no way to measure the hydraulic unstability of the sea ground due to tidal flow quantitatively. In this study, conventional hydraulic resistance measurement apparatus was improved to consider direction change of the current flow. Various artificial clayey soil specimens were made from Kaolinite and Jumunjin standard sand and hydraulic resistance tests were performed by changing the flow direction to validate the effect of the direction change on the scour of the seafloor.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1060-1064
• /
• 2010

Ground anchors are mostly used to improve the resistance capacity of retaining walls. The end of the anchor is connected to retaining wall through tendons and the forces in tendons are transferred to ground. In this study, we plan that the new anchor system increases the tension force in tendons and improves the pullout resistance characteristics of the system. In order to increase the pullout resistance capacity of existing anchor system, the new anchor system is made by attaching four steel sticks to the tip of anchor end. So the field test results showed that the pullout resistance capacity of the wedge-shaped ground anchor was acceptable to elastic displacement range.