• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.415-426
• /
• 2010

Post-grouting for the drilled shaft is known to increase the end bearing capacity of pile 2~3 times higher by consolidating and reinforcing the disturbed ground containing slime around the pile end. However, the general design guideline for post-grouting has not been established yet in Korea. Especially in the domestic application, the post-grouting is employed just for repairing the pile with the unacceptable resistance rather than for increasing the design resistance of pile. Therefore, little is reported about the effect of post-grouting on the pile resistance itself. In this study, the effect of post-grouting on the resistance of drilled shafts installed in the weathered rock in Korea was estimated by performing the bi-directional load tests on the piles with and without the post-grouting. The test results presented that the initial slope of end bearing-base displacement curve in the pile with post-grouting was 4 times higher than that without post-grouting. At the acceptable settlement (1% of pile diameter), the end bearing capacities of piles with and without the post-grouting were estimated to be 12.0 MPa and 7.0 MPa, respectively, indicating that the post-grouting could increase the end bearing resistance of pile in weathered rock more than 70%.

• Geomechanics and Engineering
• /
• 제29권5호
• /
• pp.509-522
• /
• 2022

Tail-grouting is an effective measure in shield engineering for filling the gap at the shield tail to reduce ground deformation. However, the gap-filling ratio affects the value of the gap parameters, leading to different surface settlements. It is impossible to adjust the fill ratio indiscriminately to study its effect, because the allowable adjustment range of the grouting quantity is limited to ensure construction site safety. In this study, taking the shield tunnel section between Chaoyanggang Station and Shilihe Station of Beijing Metro Line 17 as an example, the correlation between the tail-grouting parameter and the surface settlement is investigated and the optimal grouting quantity is evaluated. This site is suitable for conducting field tests to reduce the tail-grouting quantity of shield tunneling over a large range. In addition, the shield tunneling under different grouting parameters was simulated. Furthermore, we analyzed the evolution law of the surface settlement under different grouting parameters and obtained the difference in the settlement parameters for each construction stage. The results obtained indicate that the characteristics of the grout affect the development of the surface settlement. Therefore, reducing the setting time or increasing the initial strength of the grout could effectively suppress the development of surface subsidence. As the fill ratio decreases, the loose zone of the soil above the tunnel expands, and the soil deformation is easily transmitted to the surface. Meanwhile, owing to insufficient grout support, the lateral pressure on the tunnel segments is significantly reduced, and the segment moves considerably after being removed from the shield tail.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.399-406
• /
• 2004

This paper is experimental study on the effect of improved soil strength which was grouted by pressure grouting method for prevent collapse the tunnel's face during excavate tunnel. This study performs to investigate the proper grouting pressure and grouting method through pressure grouting laboratory model tests using loose dense sandy soil using specially designed and fabricated device($180cm{\times}220cm{\times}300cm$) under changing condition of injection in this test The investigation is carried out through measuring the size and shape of grout bulb, elastic modulus by pressure-meter test Elastic modulus was estimated using relation stress with strain which is result the uni-direction compressive strength test for cured grouted bulb under water during 28days. From these test results, the amount of increased elastic modulus of grouted zone was suggested.

• 설비공학논문집
• /
• 제17권4호
• /
• pp.364-369
• /
• 2005

An experimental study was conducted on the thermal conductivity of various grouting materials for geothermal heat exchanger which is used as a heat sink or source in the heat pump system. The grouting of the vertical heat exchanger is important for environmental and heat transfer reasons and is generally accomplished by the placement of a low permeability material into the annular space between the borehole wall and the pipes suspended in the borehole. In this study, a lab scale test apparatus was made and measured the thermal conductivity of four grouting materials. As a result, the temperature rising tendency was similar among them, but the increasing rate was different. Thus the thermal conductivity showed a maximum difference of $27\%$ among grouting materials.

• 한국지반환경공학회 논문집
• /
• 제14권3호
• /
• pp.19-27
• /
• 2013

최근, 갑작스런 집중호우로 인하여 자연 및 인공사면의 붕괴가 종종 발생하고 있다. 이를 예방하기 위한 여러 가지 보강공 법들이 개발되어 적용되고 있다. 그 중에서도 쏘일네일링 공법은 시공성과 경제성 등의 이유로 그 활용이 증대되고 있다. 쏘일네일링 공법은 다른 보강공법들과 함께 사용하는 경우도 있으며, 또한 강재와 시멘트그라우팅과의 일종의 복합 구조체로서 지반과 그라우팅사이의 마찰력을 활용하는 공법이다. 본 연구에서는 선단확장형 쏘일네일링 공법을 개발하였으며, 이는 네일 끝단에 앵커체가 부착되어 있다. 이 앵커체는 네일링 작업 중 네일 끝단에서 확개되면서 지반에 정착되게 된다. 본 연구에서는 네일링 시공 후 그라우팅을 하지 않은 상태와 그라우팅 후 양생이 된 경우 각각에 대해 현장인발저항시험을 실시하였다. 시험결과로부터 선단확장형 쏘일네일의 선단쐐기력을 분석하였으며, 거동특성을 종합적으로 고찰하였다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2006년도 공동학술대회 논문집
• /
• pp.79-82
• /
• 2006

This paper presents to examine the ability of an electrical resistivity method to monitor the grouting effect at subsidence area. To monitor the changes in ground resistivity before and during the grout, series of electrical resistivity monitoring surveys have been conducted. Data has acquired in the form of grid making nine lines parallel to road and four lines traverse the road. Two kinds of electrode arrays modify pole-pole and dipole-dipole arrays were used during resistivity data acquisition. In this paper, the results show that electrical prospecting is an effective method to detect low resistivity imaging zone by grout during the ground reinforcement.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1995년도 가을 학술발표회 논문집
• /
• pp.25.2-38
• /
• 1995

the Effect of steel pipe reinforced multi-step grouting(SPRG) technique to inrove the ground far ahead of the excavation face was investigated by means of numerical analysis. It was found taht the nonlinear 3-D FEM program performed well to evaluate the usefulness of the SPRG technique in soft ground tunnelling, and about 20% of settlement control in this particular case possible. Therefore in urban subway tunnel construction, the New Austirial Tunnelling Method can be satisfactorily applied even in poor ground conditon with aid of the SPRG technique.

• Geomechanics and Engineering
• /
• 제16권2호
• /
• pp.159-168
• /
• 2018

In this study, a real-time grouting management system based on the clogging theory was established to manage injection procedure in real time. This system is capable of estimating hydraulic permeability with the passage of time as the grout permeates through the ground, and therefore, capable of estimating real time injection distance and flow rate. By adopting the Controlled Injection Pressure (CoIP) model, it was feasible to predict the grout permeation status with the elapse of time by consecutively updating the hydraulic gradient and flow rate estimated from a clogging-induced alteration of pore volume. Moreover, a method to estimate the volume of the fractured gap according to the reduction in injection pressure was proposed. The validity of the proposed system was successfully established by comparing the estimated values with the measured field data.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1063-1068
• /
• 2008

When construction of high pressure jet-grouting is to be performed, it has been reported that applied cement slurry which hasn't got dried out can cause severe environmental pollution, and can flow into near streams and fish farms. Several laboratory tests were performed in this study in order to verify safety of paste-like grouting material that was developed newly to be applied to void in the ground. According to experimental test results, it is proved to be so safe that application of the newly developed flowable grouting material can prevent the materials from spilling into surrounding areas and is not harmful to fishes.

• 한국지반신소재학회논문집
• /
• 제19권4호
• /
• pp.11-20
• /
• 2020

본 연구에서는 연약지반의 개량 및 부등침하가 일어난 건물의 복원 등에 사용할 수 있는 컴팩션 그라우팅 공법을 소개하였다. 기존 컴팩션 그라우팅 공법에서 사용되는 펌프는 1공씩 주입하는 시스템으로 시공 효율성이 저하되고,아날로그 주입방식으로 현장 작업자가 수동으로 시공을 관리하여 일관된 품질관리가 어려웠다. 기존 시공에서의 문제점을 해결하기 위하여 펌프와 품질관리 시스템을 개발하였다. 품질관리 시스템은 주입재료의 자동 배합 시스템, 다중 동시 주입 펌프, 주입관리 모니터링 시스템으로 구성하였다. 현장 시험을 통해 품질관리 시스템의 성능을 검증하였고 컴팩션 그라우팅 공법의 시험시공 후 품질 시험을 통하여 지반개량 성능을 확인하였다. 따라서 개발된 통합 품질관리 시스템을 활용한다면 시공 및 품질 확인이 어려운 현장에서 일관된 품질의 보장과 시공의 효율성 및 안정성을 향상시킬 수 있을 것으로 기대된다.