• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.6
• /
• pp.130-138
• /
• 2007

To protect the surface of ground-cutting slopes occurring at the national road substitute detour [roundabout road]construction jobsite between Munduk and Wubokgu within the jurisdiction of Pohang-si and environment-friendly road construction, a test execution of re-vegetation measures on the major slopes was done and the results are as follows : As a result of finding out the number of sprouting individuals on the test construction site, the average number of sprouting individuals on the three test spots by the method of revegetation measures D, revegetation measures A, and revegetation measures B was 1,292 number of per square meter, 1,190 number of per square meter, and 1,095 number of per square meter respectively, which statistics were higher than those of test spot by the revegetation measures C. As a result of finding out living plant's breeding index [weight in dried state], the average dried weight of living plant at the test spot by the method of revegetation measures B, in case of foreign herbal species, was the highest marking 8.96 grams per square meter, and the next was 6.86grams per square meter by the method of revegetation measures D, and the next after was 6.80 grams per square meter by the method of revegetation measures A, and the last 5.93 grams per square meter by the method of revegetation measures C. As a result of finding out the covering degree on the slopes, the same average covering degree of 80% and 77.5% in revegetation measures A and revegetation measures D individually, which showed a somewhat higher covering degree than those of revegetation measures B and revegetation measures C. As a result of finding out appearing plants on the test construction site, seeding plant life was found to be sprouting on all test spot while native and foreign herbal species and herbaceous plant as well as shrubs were growing in good harmony with each other. However, in case of revegetation measures B and revegetation measures C method, foreign plant species are dominantly growing. As a result of inspecting rifts on the slopes and the excavated state by water, there existed cracks in some of base materials only in revegetation measures C method applied spot.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.2
• /
• pp.1-15
• /
• 2007

A variety of revegetation methods are being utilized and developed. However, most of revegetation methods used on highway slopes in Korea are based on foreign-introduced plant varieties to stabilize road surfaces and to administer afforestation for surface covering at an earlier phase. Therefore. it results in various problems. such as failure to achieve harmony with the surrounding vegetation and 10 cause re-denudation of slopes as the foreign-in introduced plant varieties wane out from 2~3 years after hydro-seeding, etc. In addition, some of the revegetation plants seeded in the earlier phase grow excessively high, thus causes successional problems, such as to inhibit the invasion of the secondary vegetation from the surrounding areas, etc. Therefore, in this study, 160 slopes located in the nationwide express highways have been investigated and analyzed in order to produce basic data for restoration of ecological environment in slopes created on a long-term basis by investigating and analyzing locational characteristics of cut and filled slopes in express highways, status of revegetation methods, characteristics of soil and plant-ecological environment. 1. Investigation on cut and embanked slopes in express highways was carried out in the total of 160 locations, which include 108 cut slopes and 52 embanked slopes. As a whole, the most frequently used revegetation method was seed spray, which was found to be used in the total of 55 target slops investigated. 2. Planting method of Wistaria floribunda applied to some of the blasted rock zones was found to cause damages as Wistaria floribunda trailed up the surrounding vegetation and the secondary invaded trees. In order to prevent this, this method must be used only in the lowest parts of large-sized slopes. Also, it will be required to administer continuous management and maintenance in the areas already planted with this plants. 3. The areas of blasted rock and ripping rock slopes were applied with coir net (net + seeding) method. However, many of these areas failed in achieving ground covering. Most areas where revegetation was in progress, they were covered with Eragrostis curvula(Weeping lovegrass) only. In areas with soil, such as decomposition of granite, where afforestation is difficult. In this slopes, soil base must be improved by hrdroseeding with thin-layer vegetation base application methods in order to achieve success in afforestation with native plants. 4. Woody species, rather than herb species, are more helpful in stabilization of slope surfaces. Therefore, it is important to be able to grow and protect woody species on highway slopes. Growth of woody vegetation is most largely influenced by soil depth. Thus, when hydro-seeding woody plants, it is recommended to apply at the upper layer of the slopes, which is capable to sufficiently provide the fundamentals required in plant growth.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.31-38
• /
• 2013

After debris flow caused damage during recent years, many scholars and engineers have thrown their effort into analyzing risk from debris flow in Korea. But it is hard to predict damage by debris flow taken place in wide area. Recently, SINMAP program is widely well used to estimate the amount of debris flow and its' range. In order to make frequent use of it, the most important thing is selection of accurate input parameters. In-situ experiments, which are avaliable in the mountain, is to be suggested to get dependable input parameters for SINMAP. Those are permeability, cohesion, density, friction angle and thickness in SINMAP. To get those, test pit, block sampling, in-situ density test, auger boring, permeability test on ground surface, borehole shear test and dynamic cone test and so forth were selected. In addition, the reliability of the results will be increased through comparing with those by laboratory tests. Hence, the experiments are hard to enter the sites without temporary road and, if possible, licensing and many times are needed, too. Small size experiments are indeed necessary to get accurate parameters.

• Geotechnical Engineering
• /
• v.10 no.2
• /
• pp.25-40
• /
• 1994

In order to investigate behavior of lateral flow by plasticity of soils and construction control due to it, in the case of unsymmetrical surcharge load on the soft soils, we examine the existing theoretical background, and compared and analysed the experimental results by model test. After model test fabricated by model test apparatus, which made full remolding samples of soft soils, we observed the state of behavior for deformation with increasing load step to constant time interval. The critical surcharge and ultimate capacity showed tendency to approach to the proposed value of Jaky and Meyerhof, and the lateral flow pressure of which the maximum value was acted on the depth calculated by z/H=0.26+1.71cu and one third value of the maximum lateral flow pressure acted on the ground surface, approach the trapezoid distribution And maximum lateral flow pressure will be calculated by proposed equation of Hong or simple equation which($\alpha=0.4$) the flow pressure coefficient . of proposed equation by Tschebotarioff exchanged to($\alpha=K_0$) . Basides, the failure surcharge by [(q/$y_m$)-q] and [$S_y-(y_m/S_y)$] showed the smaller than ultimate bearing capacity, especially failure criteria line of control diagram of [$S_y(y_m/S_y)$] will be calculated by following equation. $S_y.=3.15exp[-0.58(y_m/S_y)$

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.106-111
• /
• 2012

Drying characteristic of high moisture coal using a 5 kg/hr bench scale flash dryer was investigated. Moisture content and heating value of raw coal as received basis were 29.74 wt% and 4,270 kcal/kg, respectively. Gas inlet temperature and gas inlet flow rate were $400{\sim}600^{\circ}C$ and 10~20 m/sec, respectively. The raw coal was ground and classified to the particle size range of $100{\sim}2,000{\mu}m$. The moisture removal rate of raw coal was dramatically increased with increasing gas inlet temperature and decreasing gas inlet flow rate. The heating value of dried coal was increased to 5,100~5,900 kcal/kg. To examine the chemical change on the surface of high moisture coal during flash drying process, FT-IR spectral analysis was carried out. As a result, major changes in hydroxyl, carboxyl and carbonyl peak was confirmed.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2000.09a
• /
• pp.132-146
• /
• 2000

Seismic refraction survey was performed for 10 lines along NE-SW and NW-SE directions above Nampoong gallery at Makyo-ri, Dogye, Samcheok, Kangwon-do. 48 geophones were laid in line with the interval of 1m, and a 5Kg hammer was used as a source at 5 points for each line. Data processing was done using reciprocal time method, GRM, and traveltime tomography which utilizes wavefront expansion method for forward process and STRT for inversion. The result shows that the first layer has its lower boundary between 3.49m and 8.88m. The P-wave velocity of the first and the second layer were estimated as 270${\~}$360m/s and 1550${\~}$1940m/s respectively. When the boundary of the first and second layer is smooth enough and the velocity difference is large enough, GRM has little advantage over reciprocal time method. The result of reciprocal method and traveltime tomography shows consistency. The northeast part of the boundary has syncline structure, which is similar to the topography above. This implies that the collapse of the cavities of Nampoong gallery result in the subsidence of the ground surface. The subsidence is in progress across the Youngdong railroad, therefore a proper reinforcement work is required.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2000.09a
• /
• pp.112-131
• /
• 2000

In spite of its many strong points, pole-pole electrode configuration is not often used for ground electrical resistivity survey except for bore hole survey as normal logging and for archaeological investigation. Above all, poor spatial resolution of pole-pole survey may be responsible for this. But recent experiences so far gained by the present authers lead them to think that pole-pole survey can be at least a viable means of reconnaissance survey in near-surface conductive environment and an effective interpretational scheme may augment its resolution. As well known, a response of any other electrode configuration is a linear combination of pole-pole responses. Based on this principle of linear superposition and the principle of reciprocity, the other 'responses' can be derived with simple additions and subtractions of pole-pole responses. Though such responses are not always correct due to the adverse effects of noises, combined with the potential decay curves, they can be helpful to interprete better pole-pole survey data especially in connection of the resolution. This can be comparable to the use of the first or second derivatives of gravity and magnetic intensity surveys.

• Geophysics and Geophysical Exploration
• /
• v.15 no.4
• /
• pp.155-162
• /
• 2012

The Thomsen-Haskell method was used to determine sensitivities of the Rayleigh-wave phase velocities and spectral amplitude of vertical ground motion to insertion of a single velocity-anomaly layer into overburden underlain by a basement. The reference model comprised a 9-m thick overburden with shear-wave velocity (${\nu}_s$ of 300 m/s above a half-space with ${\nu}_s$ = 1000 m/s. The inserted layer, with a velocity of 150, 225, 375, or 450 m/s and a thickness of 1, 2, or 3 m, was placed at depths increasing from the surface in increments of 1 m. Phase velocities were computed for frequencies of 4 to 30 Hz. For inserted layer models, we placed an anomalous layer with thickness of 1 ~ 3 m, shear-wave velocity of 150 ~ 450 m/s, and at depths of 0 ~ 8 m in the overburden. The frequency range of 8 ~ 20 Hz were the most sensitive to the difference of $C_R$ between the inserted and reference models (${\Delta}C_R$) for h = 1 m and the frequency range got wide as h increased. For all of the models, the spectral amplitudes of the fundamental mode exceeded those of the $1^{st}$-higher mode except at frequencies just above the low-frequency cutoff of the $1^{st}$-higher mode.

• Korean Journal of Optics and Photonics
• /
• v.22 no.4
• /
• pp.184-190
• /
• 2011

A compact imaging spectrometer (COMIS) was developed for a microsatellite STSAT-3. The satellite is now rescheduled to be launched into a low sun-synchronous Earth orbit (~700 km) by the end of 2012. Its main operational goal is the imaging of the Earth's surface and atmosphere with ground sampling distance of 27 m and 2 - 15 nm spectral resolution over visible and near infrared spectrum (0.4 - 1.05 ${\mu}m$). A flight model of COMIS was developed following an engineering model that had successfully demonstrated hyperspectral imaging capability and structural rigidity. In this paper we report the environmental test results of the flight model. The mechanical stiffness of the model was confirmed by a small shift of the natural frequency i.e., < 1% over 10 gRMS random vibration test. Electrical functions of the model were also tested without showing any anomalies during and after vacuum thermal cycling test with < $10^{-5}$ torr and $-30^{\circ}C\;-\;35^{\circ}C$. The imaging capability of the model, represented by a modulation transfer function (MTF) value at the Nyquist frequency, was also kept unvaried after all those environmental tests.

• Journal of Life Science
• /
• v.23 no.3
• /
• pp.341-346
• /
• 2013

The disappearance of seaweed flora in some rocky areas, which is known as algal whitening, barren ground, coralline flats, or deforested areas, is associated with some species of coralline algae. To determine the biological characteristics of a representative species of crustose coralline alga, the 18S rDNA gene was sequenced to identify the genus Lithophyllum. According to its morphological and distributional characteristics, it was deduced to be L. yessoense. Viability was measured using triphenyl tetrazolium chloride and showed high viability from December to February. Culture conditions of $16^{\circ}C$, a 16 hr light, 8 hr dark cycle, and 30 ${\mu}E/m^2/s$ light intensity were optimal for maintaining the viability of the alga for up to five days. Included in the fatty acids was 9.7% ${\omega}$-3 eicosapentaenoic acid. An electron microscopy scan of the surface structure revealed round craters about 3.6 ${\mu}m$ in diameter, which were covered with rough, irregular, and angular polygon-shaped structures about 1.0 to 3.7 ${\mu}m$ in size. Based on the composition and structure found in our study, biomimetic coralline alga might become an environmentally friendly antifouling material against the attachment of soft foulants.